Question 270A port migration restores connectivity but the ONTAP data LIF continues running on a non-home path and operators assume it automatically reverts regardless of policy. Which ONTAP behavior explains why the original approach does not meet the requirement? LIF auto-revert determines whether it returns home after the original port becomes healthy. LIF failover policy cannot compensate for incorrect VLAN reachability on the destination port. An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain. Successful IP connectivity narrows the defect to naming or authentication rather than link failure. ExplanationCorrect Answer A:LIF auto-revert determines whether it returns home after the original port becomes healthy. The corrective design is: Review the LIF's home-node/home-port and auto-revert settings, then use the supported revert workflow when appropriate. A relevant test is: Inspect LIF current versus home location and test a safe failover/revert cycle. Other Answers B:LIF failover policy cannot compensate for incorrect VLAN reachability on the destination port. That mechanism fits a different troubleshooting network components failure: An ONTAP data LIF works on its home port, but on failover it moves to an uplink with no access to the client VLAN. Here the decisive mechanism is: LIF auto-revert determines whether it returns home after the original port becomes healthy. C:An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain. That mechanism fits a different troubleshooting network components failure: After a switch replacement, an SVM's NAS LIF remains up but clients can no longer mount because its home port belongs to the wrong broadcast domain. Here the decisive mechanism is: LIF auto-revert determines whether it returns home after the original port becomes healthy. D:Successful IP connectivity narrows the defect to naming or authentication rather than link failure. That mechanism fits a different troubleshooting network components failure: A NAS client can reach the ONTAP LIF by IP but not by its SVM DNS name after a zone migration. Here the decisive mechanism is: LIF auto-revert determines whether it returns home after the original port becomes healthy.
Question 271A port migration restores connectivity but the ONTAP data LIF continues running on a non-home path and operators assume it automatically reverts regardless of policy. Which observation provides the strongest evidence that the issue was corrected? Trigger a test port outage and verify the LIF's alternate port maintains client connectivity. Inspect LIF current versus home location and test a safe failover/revert cycle. Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction. Resolve the share name from the client and compare it with the intended LIF IP before mounting. ExplanationCorrect Answer B:Inspect LIF current versus home location and test a safe failover/revert cycle. This checks whether the remediation works: Review the LIF's home-node/home-port and auto-revert settings, then use the supported revert workflow when appropriate. The governing behavior is: LIF auto-revert determines whether it returns home after the original port becomes healthy. Other Answers A:Trigger a test port outage and verify the LIF's alternate port maintains client connectivity. That check tests the separate condition: An ONTAP data LIF works on its home port, but on failover it moves to an uplink with no access to the client VLAN. It would not establish the required result here: Inspect LIF current versus home location and test a safe failover/revert cycle. C:Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction. That check tests the separate condition: After a switch replacement, an SVM's NAS LIF remains up but clients can no longer mount because its home port belongs to the wrong broadcast domain. It would not establish the required result here: Inspect LIF current versus home location and test a safe failover/revert cycle. D:Resolve the share name from the client and compare it with the intended LIF IP before mounting. That check tests the separate condition: A NAS client can reach the ONTAP LIF by IP but not by its SVM DNS name after a zone migration. It would not establish the required result here: Inspect LIF current versus home location and test a safe failover/revert cycle.
Question 272A port migration restores connectivity but the ONTAP data LIF continues running on a non-home path and operators assume it automatically reverts regardless of policy. Which preventive practice most directly reduces recurrence of this failure? Include all failover target VLANs in network cutover acceptance. Run automated port-reachability validation after network refreshes. Test DNS changes for expected storage server records before switching users. Track LIFs persistently off-home and review auto-revert policy after maintenance. ExplanationCorrect Answer D:Track LIFs persistently off-home and review auto-revert policy after maintenance. This addresses the recurring cause: LIF auto-revert determines whether it returns home after the original port becomes healthy. It keeps the accepted correction in place: Review the LIF's home-node/home-port and auto-revert settings, then use the supported revert workflow when appropriate. Other Answers A:Include all failover target VLANs in network cutover acceptance. This safeguard targets a different repeat failure: An ONTAP data LIF works on its home port, but on failover it moves to an uplink with no access to the client VLAN. For the present risk, the necessary control is: Track LIFs persistently off-home and review auto-revert policy after maintenance. B:Run automated port-reachability validation after network refreshes. This safeguard targets a different repeat failure: After a switch replacement, an SVM's NAS LIF remains up but clients can no longer mount because its home port belongs to the wrong broadcast domain. For the present risk, the necessary control is: Track LIFs persistently off-home and review auto-revert policy after maintenance. C:Test DNS changes for expected storage server records before switching users. This safeguard targets a different repeat failure: A NAS client can reach the ONTAP LIF by IP but not by its SVM DNS name after a zone migration. For the present risk, the necessary control is: Track LIFs persistently off-home and review auto-revert policy after maintenance.
Question 273A Linux database host sees an iSCSI target but cannot see its new ONTAP LUN because the administrator created only the LUN, not the host-access mapping. Which ONTAP administration step most directly corrects this failure? Use the host-appropriate supported OS type and confirm initiator group/provisioning alignment before mapping. Configure supported redundant iSCSI target connectivity and host multipathing across appropriate interfaces. Include the approved initiators of both cluster members in the correct igroup and verify host cluster disk ownership rules. Create an igroup containing the host's initiator IQN and map the intended LUN to that igroup. ExplanationCorrect Answer D:Create an igroup containing the host's initiator IQN and map the intended LUN to that igroup. LUN existence on an SVM does not expose a block device until an authorized initiator has a LUN mapping. Acceptance requires: Check the host initiator IQN, inspect the mapping and rescan to confirm only the assigned LUN appears. Other Answers A:Use the host-appropriate supported OS type and confirm initiator group/provisioning alignment before mapping. This responds to another san solutions issue: An administrator creates an iSCSI LUN for a Linux host but selects an unrelated Windows OS type in its igroup and LUN settings. Its mechanism is: The configured host OS type influences ONTAP SAN device behavior and cannot be treated as cosmetic metadata. The present case instead requires: Create an igroup containing the host's initiator IQN and map the intended LUN to that igroup. B:Configure supported redundant iSCSI target connectivity and host multipathing across appropriate interfaces. This responds to another san solutions issue: An iSCSI SVM has a single data LIF, and a scheduled port-maintenance event disconnects a business-critical LUN even though the partner controller is healthy. Its mechanism is: A reachable LUN mapping is insufficient if the network transport has only one path to the initiator. The present case instead requires: Create an igroup containing the host's initiator IQN and map the intended LUN to that igroup. C:Include the approved initiators of both cluster members in the correct igroup and verify host cluster disk ownership rules. This responds to another san solutions issue: A Windows cluster shares a SAN LUN with two nodes but only one node's initiator appears in the igroup and failover leaves the second host unable to access storage. Its mechanism is: Cluster failover depends on each authorized node having a valid mapped path to the shared LUN. The present case instead requires: Create an igroup containing the host's initiator IQN and map the intended LUN to that igroup.
Question 274A Linux database host sees an iSCSI target but cannot see its new ONTAP LUN because the administrator created only the LUN, not the host-access mapping. Which technical distinction most directly explains the observed result? LUN existence on an SVM does not expose a block device until an authorized initiator has a LUN mapping. The configured host OS type influences ONTAP SAN device behavior and cannot be treated as cosmetic metadata. A reachable LUN mapping is insufficient if the network transport has only one path to the initiator. Cluster failover depends on each authorized node having a valid mapped path to the shared LUN. ExplanationCorrect Answer A:LUN existence on an SVM does not expose a block device until an authorized initiator has a LUN mapping. The corrective design is: Create an igroup containing the host's initiator IQN and map the intended LUN to that igroup. A relevant test is: Check the host initiator IQN, inspect the mapping and rescan to confirm only the assigned LUN appears. Other Answers B:The configured host OS type influences ONTAP SAN device behavior and cannot be treated as cosmetic metadata. That mechanism fits a different san solutions failure: An administrator creates an iSCSI LUN for a Linux host but selects an unrelated Windows OS type in its igroup and LUN settings. Here the decisive mechanism is: LUN existence on an SVM does not expose a block device until an authorized initiator has a LUN mapping. C:A reachable LUN mapping is insufficient if the network transport has only one path to the initiator. That mechanism fits a different san solutions failure: An iSCSI SVM has a single data LIF, and a scheduled port-maintenance event disconnects a business-critical LUN even though the partner controller is healthy. Here the decisive mechanism is: LUN existence on an SVM does not expose a block device until an authorized initiator has a LUN mapping. D:Cluster failover depends on each authorized node having a valid mapped path to the shared LUN. That mechanism fits a different san solutions failure: A Windows cluster shares a SAN LUN with two nodes but only one node's initiator appears in the igroup and failover leaves the second host unable to access storage. Here the decisive mechanism is: LUN existence on an SVM does not expose a block device until an authorized initiator has a LUN mapping.
Question 275A Linux database host sees an iSCSI target but cannot see its new ONTAP LUN because the administrator created only the LUN, not the host-access mapping. What check best verifies this change under the stated operating conditions? Check the host initiator IQN, inspect the mapping and rescan to confirm only the assigned LUN appears. Compare configured LUN and igroup OS types with NetApp host interoperability guidance and rescan the intended host. Observe session count and sustained I/O while a selected target interface is made unavailable. Move the clustered role between nodes in a test and confirm both have correct LUN visibility and consistent identifiers. ExplanationCorrect Answer A:Check the host initiator IQN, inspect the mapping and rescan to confirm only the assigned LUN appears. This checks whether the remediation works: Create an igroup containing the host's initiator IQN and map the intended LUN to that igroup. The governing behavior is: LUN existence on an SVM does not expose a block device until an authorized initiator has a LUN mapping. Other Answers B:Compare configured LUN and igroup OS types with NetApp host interoperability guidance and rescan the intended host. That check tests the separate condition: An administrator creates an iSCSI LUN for a Linux host but selects an unrelated Windows OS type in its igroup and LUN settings. It would not establish the required result here: Check the host initiator IQN, inspect the mapping and rescan to confirm only the assigned LUN appears. C:Observe session count and sustained I/O while a selected target interface is made unavailable. That check tests the separate condition: An iSCSI SVM has a single data LIF, and a scheduled port-maintenance event disconnects a business-critical LUN even though the partner controller is healthy. It would not establish the required result here: Check the host initiator IQN, inspect the mapping and rescan to confirm only the assigned LUN appears. D:Move the clustered role between nodes in a test and confirm both have correct LUN visibility and consistent identifiers. That check tests the separate condition: A Windows cluster shares a SAN LUN with two nodes but only one node's initiator appears in the igroup and failover leaves the second host unable to access storage. It would not establish the required result here: Check the host initiator IQN, inspect the mapping and rescan to confirm only the assigned LUN appears.
Question 276A Linux database host sees an iSCSI target but cannot see its new ONTAP LUN because the administrator created only the LUN, not the host-access mapping. What control should the team keep after the corrective change has passed testing? Validate host platform, protocol and OS type in the SAN provisioning request. Standardize at least two independent target paths and supported host multipath policies. Require per-host igroup/LUN mapping validation in SAN provisioning templates. Update igroup membership as part of clustered host additions and removals. ExplanationCorrect Answer C:Require per-host igroup/LUN mapping validation in SAN provisioning templates. This addresses the recurring cause: LUN existence on an SVM does not expose a block device until an authorized initiator has a LUN mapping. It keeps the accepted correction in place: Create an igroup containing the host's initiator IQN and map the intended LUN to that igroup. Other Answers A:Validate host platform, protocol and OS type in the SAN provisioning request. This safeguard targets a different repeat failure: An administrator creates an iSCSI LUN for a Linux host but selects an unrelated Windows OS type in its igroup and LUN settings. For the present risk, the necessary control is: Require per-host igroup/LUN mapping validation in SAN provisioning templates. B:Standardize at least two independent target paths and supported host multipath policies. This safeguard targets a different repeat failure: An iSCSI SVM has a single data LIF, and a scheduled port-maintenance event disconnects a business-critical LUN even though the partner controller is healthy. For the present risk, the necessary control is: Require per-host igroup/LUN mapping validation in SAN provisioning templates. D:Update igroup membership as part of clustered host additions and removals. This safeguard targets a different repeat failure: A Windows cluster shares a SAN LUN with two nodes but only one node's initiator appears in the igroup and failover leaves the second host unable to access storage. For the present risk, the necessary control is: Require per-host igroup/LUN mapping validation in SAN provisioning templates.
Question 277A dual-controller FC SAN has one host path through one fabric, and the design assumes controller HA alone guarantees no host access interruption during a fabric outage. Which change most directly meets the stated storage requirement? Install and configure the supported host multipathing stack so multiple ALUA paths are presented as one logical device. Provide redundant FC fabric paths and supported host multipathing to the mapped LUN. Follow supported NVMe/FC namespace and host ANA configuration workflows for the selected ONTAP/host combination. Apply supported Selective LUN Map, zoning or portsets to bound target paths while retaining redundancy. ExplanationCorrect Answer B:Provide redundant FC fabric paths and supported host multipathing to the mapped LUN. Controller HA cannot repair a missing independent host-to-target fabric path; host MPIO chooses surviving paths. Acceptance requires: Disable one FC fabric in a controlled test and confirm the host I/O continues through an alternate path. Other Answers A:Install and configure the supported host multipathing stack so multiple ALUA paths are presented as one logical device. This responds to another san solutions issue: A host sees multiple copies of the same LUN as separate disks after a SAN path expansion, raising a risk of file-system corruption. Its mechanism is: Without correct MPIO, the OS may interpret multiple paths to one LUN as independent disks rather than one device. The present case instead requires: Provide redundant FC fabric paths and supported host multipathing to the mapped LUN. C:Follow supported NVMe/FC namespace and host ANA configuration workflows for the selected ONTAP/host combination. This responds to another san solutions issue: A team evaluates NVMe over Fibre Channel for a supported host, but assumes conventional FC LUN igroups and SCSI multipathing rules can be reused unchanged. Its mechanism is: NVMe namespace access and ANA path semantics differ from SCSI LUN mapping and ALUA behavior. The present case instead requires: Provide redundant FC fabric paths and supported host multipathing to the mapped LUN. D:Apply supported Selective LUN Map, zoning or portsets to bound target paths while retaining redundancy. This responds to another san solutions issue: A SAN architect expects eight storage ports on several nodes to be visible to every host even though host path limits may be exceeded. Its mechanism is: More exposed targets are not automatically better; supported host/ONTAP multipath limits and optimized ownership matter. The present case instead requires: Provide redundant FC fabric paths and supported host multipathing to the mapped LUN.
Question 278A dual-controller FC SAN has one host path through one fabric, and the design assumes controller HA alone guarantees no host access interruption during a fabric outage. Why would the proposed setup fail to provide the stated behavior? Without correct MPIO, the OS may interpret multiple paths to one LUN as independent disks rather than one device. NVMe namespace access and ANA path semantics differ from SCSI LUN mapping and ALUA behavior. Controller HA cannot repair a missing independent host-to-target fabric path; host MPIO chooses surviving paths. More exposed targets are not automatically better; supported host/ONTAP multipath limits and optimized ownership matter. ExplanationCorrect Answer C:Controller HA cannot repair a missing independent host-to-target fabric path; host MPIO chooses surviving paths. The corrective design is: Provide redundant FC fabric paths and supported host multipathing to the mapped LUN. A relevant test is: Disable one FC fabric in a controlled test and confirm the host I/O continues through an alternate path. Other Answers A:Without correct MPIO, the OS may interpret multiple paths to one LUN as independent disks rather than one device. That mechanism fits a different san solutions failure: A host sees multiple copies of the same LUN as separate disks after a SAN path expansion, raising a risk of file-system corruption. Here the decisive mechanism is: Controller HA cannot repair a missing independent host-to-target fabric path; host MPIO chooses surviving paths. B:NVMe namespace access and ANA path semantics differ from SCSI LUN mapping and ALUA behavior. That mechanism fits a different san solutions failure: A team evaluates NVMe over Fibre Channel for a supported host, but assumes conventional FC LUN igroups and SCSI multipathing rules can be reused unchanged. Here the decisive mechanism is: Controller HA cannot repair a missing independent host-to-target fabric path; host MPIO chooses surviving paths. D:More exposed targets are not automatically better; supported host/ONTAP multipath limits and optimized ownership matter. That mechanism fits a different san solutions failure: A SAN architect expects eight storage ports on several nodes to be visible to every host even though host path limits may be exceeded. Here the decisive mechanism is: Controller HA cannot repair a missing independent host-to-target fabric path; host MPIO chooses surviving paths.
Question 279A dual-controller FC SAN has one host path through one fabric, and the design assumes controller HA alone guarantees no host access interruption during a fabric outage. Which result should be required before the storage change is accepted? Disable one FC fabric in a controlled test and confirm the host I/O continues through an alternate path. Inspect host multipath identity and confirm all eligible paths resolve to a single disk with controlled path failover. Discover the NVMe subsystem and namespace using approved host tooling and test ANA path recovery. Compare discovered target paths with the host support matrix and confirm resilient access after limiting paths. ExplanationCorrect Answer A:Disable one FC fabric in a controlled test and confirm the host I/O continues through an alternate path. This checks whether the remediation works: Provide redundant FC fabric paths and supported host multipathing to the mapped LUN. The governing behavior is: Controller HA cannot repair a missing independent host-to-target fabric path; host MPIO chooses surviving paths. Other Answers B:Inspect host multipath identity and confirm all eligible paths resolve to a single disk with controlled path failover. That check tests the separate condition: A host sees multiple copies of the same LUN as separate disks after a SAN path expansion, raising a risk of file-system corruption. It would not establish the required result here: Disable one FC fabric in a controlled test and confirm the host I/O continues through an alternate path. C:Discover the NVMe subsystem and namespace using approved host tooling and test ANA path recovery. That check tests the separate condition: A team evaluates NVMe over Fibre Channel for a supported host, but assumes conventional FC LUN igroups and SCSI multipathing rules can be reused unchanged. It would not establish the required result here: Disable one FC fabric in a controlled test and confirm the host I/O continues through an alternate path. D:Compare discovered target paths with the host support matrix and confirm resilient access after limiting paths. That check tests the separate condition: A SAN architect expects eight storage ports on several nodes to be visible to every host even though host path limits may be exceeded. It would not establish the required result here: Disable one FC fabric in a controlled test and confirm the host I/O continues through an alternate path.
Question 280A dual-controller FC SAN has one host path through one fabric, and the design assumes controller HA alone guarantees no host access interruption during a fabric outage. Which durable operational control best prevents this issue from recurring? Test multipathing after adapter, driver and SAN target changes. Keep separate NVMe versus SCSI connectivity checklists with version support verification. Audit dual-fabric zoning, WWPN inventory and MPIO after SAN fabric changes. Keep a documented path-count budget for every SAN host platform. ExplanationCorrect Answer C:Audit dual-fabric zoning, WWPN inventory and MPIO after SAN fabric changes. This addresses the recurring cause: Controller HA cannot repair a missing independent host-to-target fabric path; host MPIO chooses surviving paths. It keeps the accepted correction in place: Provide redundant FC fabric paths and supported host multipathing to the mapped LUN. Other Answers A:Test multipathing after adapter, driver and SAN target changes. This safeguard targets a different repeat failure: A host sees multiple copies of the same LUN as separate disks after a SAN path expansion, raising a risk of file-system corruption. For the present risk, the necessary control is: Audit dual-fabric zoning, WWPN inventory and MPIO after SAN fabric changes. B:Keep separate NVMe versus SCSI connectivity checklists with version support verification. This safeguard targets a different repeat failure: A team evaluates NVMe over Fibre Channel for a supported host, but assumes conventional FC LUN igroups and SCSI multipathing rules can be reused unchanged. For the present risk, the necessary control is: Audit dual-fabric zoning, WWPN inventory and MPIO after SAN fabric changes. D:Keep a documented path-count budget for every SAN host platform. This safeguard targets a different repeat failure: A SAN architect expects eight storage ports on several nodes to be visible to every host even though host path limits may be exceeded. For the present risk, the necessary control is: Audit dual-fabric zoning, WWPN inventory and MPIO after SAN fabric changes.