McAfee Secured

Exam Code: NS0-165

Exam Name: NetApp Certified Data Administrator, ONTAP

Certification Provider: Network Appliance

Corresponding Certification: NCDA ONTAP

100% Network Appliance NS0-165 Guaranteed Success With Testking Training Materials

Get Real NS0-165 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

60 Questions & Answers with Testing Engine

"NetApp Certified Data Administrator, ONTAP Exam", also known as NS0-165 exam, is a Network Appliance certification exam.

Pass your tests with the always up-to-date NS0-165 Exam Engine. Your NS0-165 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Network Appliance NS0-165 Practice Test 24

Question 230

A NAS SVM has two data subnets, but all client replies leave through an unrelated default gateway and one subnet exhibits asymmetric routing. Why would the proposed setup fail to provide the stated behavior?

  1. A LIF IP is reachable only when its network port, layer-2 domain and routing match the client path.
  2. A LIF can move only to targets permitted by its failover policy and network group; an empty target set leaves no working fallback.
  3. LIF IP/subnet matching does not remove the need for correct next-hop routes to off-subnet clients.
  4. LIF service policies restrict traffic roles; an IP address alone is not proof that NFS data service is allowed.

Explanation

Correct Answer

C:

LIF IP/subnet matching does not remove the need for correct next-hop routes to off-subnet clients. The corrective design is: Configure appropriate SVM routing entries for each remote client destination and validate path symmetry. A relevant test is: Use packet-path and route inspection for both subnets and verify the return path reaches clients.

Other Answers

A:

A LIF IP is reachable only when its network port, layer-2 domain and routing match the client path. That mechanism fits a different network components failure: An SVM's new NFS LIF is assigned to a port that is not reachable from the client subnet, even though another port on the same controller could reach that VLAN. Here the decisive mechanism is: LIF IP/subnet matching does not remove the need for correct next-hop routes to off-subnet clients.

B:

A LIF can move only to targets permitted by its failover policy and network group; an empty target set leaves no working fallback. That mechanism fits a different network components failure: An HA node failure causes NAS access to stop because the only SVM data LIF was configured with no eligible failover target. Here the decisive mechanism is: LIF IP/subnet matching does not remove the need for correct next-hop routes to off-subnet clients.

D:

LIF service policies restrict traffic roles; an IP address alone is not proof that NFS data service is allowed. That mechanism fits a different network components failure: A storage administrator enables an NFS server on one SVM but assigns the data LIF a management-only service policy and clients fail to reach its data service. Here the decisive mechanism is: LIF IP/subnet matching does not remove the need for correct next-hop routes to off-subnet clients.

Question 231

A NAS SVM has two data subnets, but all client replies leave through an unrelated default gateway and one subnet exhibits asymmetric routing. Which result should be required before the storage change is accepted?

  1. Use packet-path and route inspection for both subnets and verify the return path reaches clients.
  2. Compare port reachability, broadcast-domain membership and a client mount attempt after moving the LIF.
  3. Inspect `network interface show -failover` and test the selected port-loss scenario while checking client reachability.
  4. Inspect effective service-policy bindings and attempt a client NFS mount over the expected LIF.

Explanation

Correct Answer

A:

Use packet-path and route inspection for both subnets and verify the return path reaches clients. This checks whether the remediation works: Configure appropriate SVM routing entries for each remote client destination and validate path symmetry. The governing behavior is: LIF IP/subnet matching does not remove the need for correct next-hop routes to off-subnet clients.

Other Answers

B:

Compare port reachability, broadcast-domain membership and a client mount attempt after moving the LIF. That check tests the separate condition: An SVM's new NFS LIF is assigned to a port that is not reachable from the client subnet, even though another port on the same controller could reach that VLAN. It would not establish the required result here: Use packet-path and route inspection for both subnets and verify the return path reaches clients.

C:

Inspect `network interface show -failover` and test the selected port-loss scenario while checking client reachability. That check tests the separate condition: An HA node failure causes NAS access to stop because the only SVM data LIF was configured with no eligible failover target. It would not establish the required result here: Use packet-path and route inspection for both subnets and verify the return path reaches clients.

D:

Inspect effective service-policy bindings and attempt a client NFS mount over the expected LIF. That check tests the separate condition: A storage administrator enables an NFS server on one SVM but assigns the data LIF a management-only service policy and clients fail to reach its data service. It would not establish the required result here: Use packet-path and route inspection for both subnets and verify the return path reaches clients.

Question 232

A NAS SVM has two data subnets, but all client replies leave through an unrelated default gateway and one subnet exhibits asymmetric routing. Which durable operational control best prevents this issue from recurring?

  1. Review route tables whenever adding remote client networks.
  2. Check VLAN and broadcast-domain placement during LIF provisioning reviews.
  3. Alert on LIFs with no valid failover targets and retest after port changes.
  4. Validate service-policy role and actual protocol connectivity at every new LIF deployment.

Explanation

Correct Answer

A:

Review route tables whenever adding remote client networks. This addresses the recurring cause: LIF IP/subnet matching does not remove the need for correct next-hop routes to off-subnet clients. It keeps the accepted correction in place: Configure appropriate SVM routing entries for each remote client destination and validate path symmetry.

Other Answers

B:

Check VLAN and broadcast-domain placement during LIF provisioning reviews. This safeguard targets a different repeat failure: An SVM's new NFS LIF is assigned to a port that is not reachable from the client subnet, even though another port on the same controller could reach that VLAN. For the present risk, the necessary control is: Review route tables whenever adding remote client networks.

C:

Alert on LIFs with no valid failover targets and retest after port changes. This safeguard targets a different repeat failure: An HA node failure causes NAS access to stop because the only SVM data LIF was configured with no eligible failover target. For the present risk, the necessary control is: Review route tables whenever adding remote client networks.

D:

Validate service-policy role and actual protocol connectivity at every new LIF deployment. This safeguard targets a different repeat failure: A storage administrator enables an NFS server on one SVM but assigns the data LIF a management-only service policy and clients fail to reach its data service. For the present risk, the necessary control is: Review route tables whenever adding remote client networks.

Question 233

A switch uses an LACP port-channel but ONTAP is configured with independent physical ports and the team expects redundant links to function as an aggregate automatically. What should the administrator implement first to address the underlying gap?

  1. Create or verify the supported ONTAP VLAN port configuration and assign it to the correct broadcast domain.
  2. Review the LIF failover-group target ports and network capacities, adjusting placement within supported connectivity constraints.
  3. Configure an appropriate LIF failover policy and failover group with reachable eligible ports.
  4. Configure a supported ONTAP interface group consistent with switch-side link aggregation settings where appropriate.

Explanation

Correct Answer

D:

Configure a supported ONTAP interface group consistent with switch-side link aggregation settings where appropriate. Link aggregation requires both ends to agree on membership and mode; parallel cables alone are not an LACP group. Acceptance requires: Inspect ifgrp and switch bond state and test both link failure and expected throughput.

Other Answers

A:

Create or verify the supported ONTAP VLAN port configuration and assign it to the correct broadcast domain. This responds to another network components issue: A new VLAN is present on the switch but the ONTAP physical port has no matching VLAN interface, so a new data LIF cannot reach the tagged network. Its mechanism is: Switch-side VLAN configuration does not create the necessary tagged logical port in the controller network stack. The present case instead requires: Configure a supported ONTAP interface group consistent with switch-side link aggregation settings where appropriate.

B:

Review the LIF failover-group target ports and network capacities, adjusting placement within supported connectivity constraints. This responds to another network components issue: A server team upgrades from 1GbE to 10GbE and expects existing LIF failover ports to provide matching performance, but the failover group includes mixed-speed interfaces. Its mechanism is: Failover-group membership controls eligible alternate ports; an alternate low-speed path can be reachable yet undersized. The present case instead requires: Configure a supported ONTAP interface group consistent with switch-side link aggregation settings where appropriate.

C:

Configure an appropriate LIF failover policy and failover group with reachable eligible ports. This responds to another network components issue: An HA node failure causes NAS access to stop because the only SVM data LIF was configured with no eligible failover target. Its mechanism is: A LIF can move only to targets permitted by its failover policy and network group; an empty target set leaves no working fallback. The present case instead requires: Configure a supported ONTAP interface group consistent with switch-side link aggregation settings where appropriate.

Question 234

A switch uses an LACP port-channel but ONTAP is configured with independent physical ports and the team expects redundant links to function as an aggregate automatically. Which storage-system mechanism is the decisive factor in this situation?

  1. Switch-side VLAN configuration does not create the necessary tagged logical port in the controller network stack.
  2. Failover-group membership controls eligible alternate ports; an alternate low-speed path can be reachable yet undersized.
  3. A LIF can move only to targets permitted by its failover policy and network group; an empty target set leaves no working fallback.
  4. Link aggregation requires both ends to agree on membership and mode; parallel cables alone are not an LACP group.

Explanation

Correct Answer

D:

Link aggregation requires both ends to agree on membership and mode; parallel cables alone are not an LACP group. The corrective design is: Configure a supported ONTAP interface group consistent with switch-side link aggregation settings where appropriate. A relevant test is: Inspect ifgrp and switch bond state and test both link failure and expected throughput.

Other Answers

A:

Switch-side VLAN configuration does not create the necessary tagged logical port in the controller network stack. That mechanism fits a different network components failure: A new VLAN is present on the switch but the ONTAP physical port has no matching VLAN interface, so a new data LIF cannot reach the tagged network. Here the decisive mechanism is: Link aggregation requires both ends to agree on membership and mode; parallel cables alone are not an LACP group.

B:

Failover-group membership controls eligible alternate ports; an alternate low-speed path can be reachable yet undersized. That mechanism fits a different network components failure: A server team upgrades from 1GbE to 10GbE and expects existing LIF failover ports to provide matching performance, but the failover group includes mixed-speed interfaces. Here the decisive mechanism is: Link aggregation requires both ends to agree on membership and mode; parallel cables alone are not an LACP group.

C:

A LIF can move only to targets permitted by its failover policy and network group; an empty target set leaves no working fallback. That mechanism fits a different network components failure: An HA node failure causes NAS access to stop because the only SVM data LIF was configured with no eligible failover target. Here the decisive mechanism is: Link aggregation requires both ends to agree on membership and mode; parallel cables alone are not an LACP group.

Question 235

A switch uses an LACP port-channel but ONTAP is configured with independent physical ports and the team expects redundant links to function as an aggregate automatically. Which test would directly demonstrate that the required behavior now works?

  1. Validate VLAN port state, correct tagging and end-to-end test traffic from the client subnet.
  2. Inspect ifgrp and switch bond state and test both link failure and expected throughput.
  3. Force a controlled LIF migration and compare throughput and latency at both target ports.
  4. Inspect `network interface show -failover` and test the selected port-loss scenario while checking client reachability.

Explanation

Correct Answer

B:

Inspect ifgrp and switch bond state and test both link failure and expected throughput. This checks whether the remediation works: Configure a supported ONTAP interface group consistent with switch-side link aggregation settings where appropriate. The governing behavior is: Link aggregation requires both ends to agree on membership and mode; parallel cables alone are not an LACP group.

Other Answers

A:

Validate VLAN port state, correct tagging and end-to-end test traffic from the client subnet. That check tests the separate condition: A new VLAN is present on the switch but the ONTAP physical port has no matching VLAN interface, so a new data LIF cannot reach the tagged network. It would not establish the required result here: Inspect ifgrp and switch bond state and test both link failure and expected throughput.

C:

Force a controlled LIF migration and compare throughput and latency at both target ports. That check tests the separate condition: A server team upgrades from 1GbE to 10GbE and expects existing LIF failover ports to provide matching performance, but the failover group includes mixed-speed interfaces. It would not establish the required result here: Inspect ifgrp and switch bond state and test both link failure and expected throughput.

D:

Inspect `network interface show -failover` and test the selected port-loss scenario while checking client reachability. That check tests the separate condition: An HA node failure causes NAS access to stop because the only SVM data LIF was configured with no eligible failover target. It would not establish the required result here: Inspect ifgrp and switch bond state and test both link failure and expected throughput.

Question 236

A switch uses an LACP port-channel but ONTAP is configured with independent physical ports and the team expects redundant links to function as an aggregate automatically. What ongoing safeguard should be added to the ONTAP change process?

  1. Keep physical link membership and LACP configuration under paired switch/storage change control.
  2. Keep switch and ONTAP VLAN IDs synchronized through configuration reviews.
  3. Use planned failover capacity checks for network-speed upgrades.
  4. Alert on LIFs with no valid failover targets and retest after port changes.

Explanation

Correct Answer

A:

Keep physical link membership and LACP configuration under paired switch/storage change control. This addresses the recurring cause: Link aggregation requires both ends to agree on membership and mode; parallel cables alone are not an LACP group. It keeps the accepted correction in place: Configure a supported ONTAP interface group consistent with switch-side link aggregation settings where appropriate.

Other Answers

B:

Keep switch and ONTAP VLAN IDs synchronized through configuration reviews. This safeguard targets a different repeat failure: A new VLAN is present on the switch but the ONTAP physical port has no matching VLAN interface, so a new data LIF cannot reach the tagged network. For the present risk, the necessary control is: Keep physical link membership and LACP configuration under paired switch/storage change control.

C:

Use planned failover capacity checks for network-speed upgrades. This safeguard targets a different repeat failure: A server team upgrades from 1GbE to 10GbE and expects existing LIF failover ports to provide matching performance, but the failover group includes mixed-speed interfaces. For the present risk, the necessary control is: Keep physical link membership and LACP configuration under paired switch/storage change control.

D:

Alert on LIFs with no valid failover targets and retest after port changes. This safeguard targets a different repeat failure: An HA node failure causes NAS access to stop because the only SVM data LIF was configured with no eligible failover target. For the present risk, the necessary control is: Keep physical link membership and LACP configuration under paired switch/storage change control.

Question 237

After a switch replacement, an SVM's NAS LIF remains up but clients can no longer mount because its home port belongs to the wrong broadcast domain. Which proposed action best resolves the specific issue without broadening access or risk?

  1. Restrict or repair failover targets so every eligible port can reach the LIF's client subnet.
  2. Resolve the IP collision and allocate unique addresses or managed subnet IPs for the data LIFs.
  3. Inspect and repair broadcast-domain membership and port reachability for the affected VLAN.
  4. Review the LIF's home-node/home-port and auto-revert settings, then use the supported revert workflow when appropriate.

Explanation

Correct Answer

C:

Inspect and repair broadcast-domain membership and port reachability for the affected VLAN. An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain. Acceptance requires: Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction.

Other Answers

A:

Restrict or repair failover targets so every eligible port can reach the LIF's client subnet. This responds to another troubleshooting network components issue: An ONTAP data LIF works on its home port, but on failover it moves to an uplink with no access to the client VLAN. Its mechanism is: LIF failover policy cannot compensate for incorrect VLAN reachability on the destination port. The present case instead requires: Inspect and repair broadcast-domain membership and port reachability for the affected VLAN.

B:

Resolve the IP collision and allocate unique addresses or managed subnet IPs for the data LIFs. This responds to another troubleshooting network components issue: Two ONTAP LIFs accidentally receive the same static IP in one broadcast domain, and client connections alternate between controllers. Its mechanism is: Duplicate layer-3 addresses on the same network disrupt ARP resolution and stable client routing. The present case instead requires: Inspect and repair broadcast-domain membership and port reachability for the affected VLAN.

D:

Review the LIF's home-node/home-port and auto-revert settings, then use the supported revert workflow when appropriate. This responds to another troubleshooting network components issue: A port migration restores connectivity but the ONTAP data LIF continues running on a non-home path and operators assume it automatically reverts regardless of policy. Its mechanism is: LIF auto-revert determines whether it returns home after the original port becomes healthy. The present case instead requires: Inspect and repair broadcast-domain membership and port reachability for the affected VLAN.

Question 238

After a switch replacement, an SVM's NAS LIF remains up but clients can no longer mount because its home port belongs to the wrong broadcast domain. Which ONTAP behavior explains why the original approach does not meet the requirement?

  1. LIF failover policy cannot compensate for incorrect VLAN reachability on the destination port.
  2. Duplicate layer-3 addresses on the same network disrupt ARP resolution and stable client routing.
  3. LIF auto-revert determines whether it returns home after the original port becomes healthy.
  4. An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain.

Explanation

Correct Answer

D:

An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain. The corrective design is: Inspect and repair broadcast-domain membership and port reachability for the affected VLAN. A relevant test is: Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction.

Other Answers

A:

LIF failover policy cannot compensate for incorrect VLAN reachability on the destination port. That mechanism fits a different troubleshooting network components failure: An ONTAP data LIF works on its home port, but on failover it moves to an uplink with no access to the client VLAN. Here the decisive mechanism is: An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain.

B:

Duplicate layer-3 addresses on the same network disrupt ARP resolution and stable client routing. That mechanism fits a different troubleshooting network components failure: Two ONTAP LIFs accidentally receive the same static IP in one broadcast domain, and client connections alternate between controllers. Here the decisive mechanism is: An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain.

C:

LIF auto-revert determines whether it returns home after the original port becomes healthy. That mechanism fits a different troubleshooting network components failure: A port migration restores connectivity but the ONTAP data LIF continues running on a non-home path and operators assume it automatically reverts regardless of policy. Here the decisive mechanism is: An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain.

Question 239

After a switch replacement, an SVM's NAS LIF remains up but clients can no longer mount because its home port belongs to the wrong broadcast domain. Which observation provides the strongest evidence that the issue was corrected?

  1. Trigger a test port outage and verify the LIF's alternate port maintains client connectivity.
  2. Inspect ARP and ONTAP LIF addresses, correct the collision and retest stable client sessions.
  3. Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction.
  4. Inspect LIF current versus home location and test a safe failover/revert cycle.

Explanation

Correct Answer

C:

Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction. This checks whether the remediation works: Inspect and repair broadcast-domain membership and port reachability for the affected VLAN. The governing behavior is: An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain.

Other Answers

A:

Trigger a test port outage and verify the LIF's alternate port maintains client connectivity. That check tests the separate condition: An ONTAP data LIF works on its home port, but on failover it moves to an uplink with no access to the client VLAN. It would not establish the required result here: Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction.

B:

Inspect ARP and ONTAP LIF addresses, correct the collision and retest stable client sessions. That check tests the separate condition: Two ONTAP LIFs accidentally receive the same static IP in one broadcast domain, and client connections alternate between controllers. It would not establish the required result here: Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction.

D:

Inspect LIF current versus home location and test a safe failover/revert cycle. That check tests the separate condition: A port migration restores connectivity but the ONTAP data LIF continues running on a non-home path and operators assume it automatically reverts regardless of policy. It would not establish the required result here: Check switch VLAN maps, ONTAP port reachability and a mount from the required subnet after correction.

Question 240

After a switch replacement, an SVM's NAS LIF remains up but clients can no longer mount because its home port belongs to the wrong broadcast domain. Which preventive practice most directly reduces recurrence of this failure?

  1. Run automated port-reachability validation after network refreshes.
  2. Include all failover target VLANs in network cutover acceptance.
  3. Automate uniqueness checks against IP address management during LIF creation.
  4. Track LIFs persistently off-home and review auto-revert policy after maintenance.

Explanation

Correct Answer

A:

Run automated port-reachability validation after network refreshes. This addresses the recurring cause: An administratively up LIF does not guarantee layer-2 reachability to the correct client broadcast domain. It keeps the accepted correction in place: Inspect and repair broadcast-domain membership and port reachability for the affected VLAN.

Other Answers

B:

Include all failover target VLANs in network cutover acceptance. This safeguard targets a different repeat failure: An ONTAP data LIF works on its home port, but on failover it moves to an uplink with no access to the client VLAN. For the present risk, the necessary control is: Run automated port-reachability validation after network refreshes.

C:

Automate uniqueness checks against IP address management during LIF creation. This safeguard targets a different repeat failure: Two ONTAP LIFs accidentally receive the same static IP in one broadcast domain, and client connections alternate between controllers. For the present risk, the necessary control is: Run automated port-reachability validation after network refreshes.

D:

Track LIFs persistently off-home and review auto-revert policy after maintenance. This safeguard targets a different repeat failure: A port migration restores connectivity but the ONTAP data LIF continues running on a non-home path and operators assume it automatically reverts regardless of policy. For the present risk, the necessary control is: Run automated port-reachability validation after network refreshes.

NetApp Certified Data Administrator, ONTAP (NS0-165) Practice Tests