Question 310An iSCSI initiator logs in to one target but loses connectivity to the other after a network change, and the LUN remains healthy. Why would the proposed setup fail to provide the stated behavior? LUN ID is assigned for a mapping and must remain unambiguous to the host initiator, independent of a friendly volume name. LUN visibility relies on both fabric discovery and authorized initiator mapping; a healthy volume alone does not establish access. Unbounded target discovery can violate host multipath limits even if each individual link works. An inactive transport session can be caused by target network reachability even while the block device itself is intact. ExplanationCorrect Answer D:An inactive transport session can be caused by target network reachability even while the block device itself is intact. The corrective design is: Check target iSCSI LIF reachability, VLANs, routes and initiator discovery for the failed network. A relevant test is: Test TCP connectivity to the iSCSI target from each host NIC and inspect active session reports. Other Answers A:LUN ID is assigned for a mapping and must remain unambiguous to the host initiator, independent of a friendly volume name. That mechanism fits a different troubleshooting san solutions failure: A newly provisioned LUN appears under an unexpected device number and an administrator assumes the ONTAP volume name controls its host SCSI identifier. Here the decisive mechanism is: An inactive transport session can be caused by target network reachability even while the block device itself is intact. B:LUN visibility relies on both fabric discovery and authorized initiator mapping; a healthy volume alone does not establish access. That mechanism fits a different troubleshooting san solutions failure: A mapped FC LUN is missing from one host, but other hosts access it; administrators propose recreating the volume before checking zoning. Here the decisive mechanism is: An inactive transport session can be caused by target network reachability even while the block device itself is intact. C:Unbounded target discovery can violate host multipath limits even if each individual link works. That mechanism fits a different troubleshooting san solutions failure: A large SAN rollout creates more discovered target paths than the host supports and causes login instability on multiple servers. Here the decisive mechanism is: An inactive transport session can be caused by target network reachability even while the block device itself is intact.
Question 311An iSCSI initiator logs in to one target but loses connectivity to the other after a network change, and the LUN remains healthy. Which result should be required before the storage change is accepted? Test TCP connectivity to the iSCSI target from each host NIC and inspect active session reports. Compare ONTAP mapping identifiers with discovered host SCSI target/LUN numbers. Compare target WWPN discovery and igroup mappings for the failed host with a working reference host. Enumerate host paths before and after scoping and check stable I/O under a single-path failure. ExplanationCorrect Answer A:Test TCP connectivity to the iSCSI target from each host NIC and inspect active session reports. This checks whether the remediation works: Check target iSCSI LIF reachability, VLANs, routes and initiator discovery for the failed network. The governing behavior is: An inactive transport session can be caused by target network reachability even while the block device itself is intact. Other Answers B:Compare ONTAP mapping identifiers with discovered host SCSI target/LUN numbers. That check tests the separate condition: A newly provisioned LUN appears under an unexpected device number and an administrator assumes the ONTAP volume name controls its host SCSI identifier. It would not establish the required result here: Test TCP connectivity to the iSCSI target from each host NIC and inspect active session reports. C:Compare target WWPN discovery and igroup mappings for the failed host with a working reference host. That check tests the separate condition: A mapped FC LUN is missing from one host, but other hosts access it; administrators propose recreating the volume before checking zoning. It would not establish the required result here: Test TCP connectivity to the iSCSI target from each host NIC and inspect active session reports. D:Enumerate host paths before and after scoping and check stable I/O under a single-path failure. That check tests the separate condition: A large SAN rollout creates more discovered target paths than the host supports and causes login instability on multiple servers. It would not establish the required result here: Test TCP connectivity to the iSCSI target from each host NIC and inspect active session reports.
Question 312An iSCSI initiator logs in to one target but loses connectivity to the other after a network change, and the LUN remains healthy. Which durable operational control best prevents this issue from recurring? Maintain consistent mapping conventions and detect duplicate LUN IDs during changes. Retest SAN LIF paths whenever target switches or subnets change. Audit FC zoning and initiator membership following HBA replacement. Enforce platform-specific maximum paths in SAN host standards. ExplanationCorrect Answer B:Retest SAN LIF paths whenever target switches or subnets change. This addresses the recurring cause: An inactive transport session can be caused by target network reachability even while the block device itself is intact. It keeps the accepted correction in place: Check target iSCSI LIF reachability, VLANs, routes and initiator discovery for the failed network. Other Answers A:Maintain consistent mapping conventions and detect duplicate LUN IDs during changes. This safeguard targets a different repeat failure: A newly provisioned LUN appears under an unexpected device number and an administrator assumes the ONTAP volume name controls its host SCSI identifier. For the present risk, the necessary control is: Retest SAN LIF paths whenever target switches or subnets change. C:Audit FC zoning and initiator membership following HBA replacement. This safeguard targets a different repeat failure: A mapped FC LUN is missing from one host, but other hosts access it; administrators propose recreating the volume before checking zoning. For the present risk, the necessary control is: Retest SAN LIF paths whenever target switches or subnets change. D:Enforce platform-specific maximum paths in SAN host standards. This safeguard targets a different repeat failure: A large SAN rollout creates more discovered target paths than the host supports and causes login instability on multiple servers. For the present risk, the necessary control is: Retest SAN LIF paths whenever target switches or subnets change.
Question 313Host monitoring reports high I/O latency but the ONTAP controller's disk latency is low; one FC fabric also shows retransmits and congestion alarms. What should the administrator implement first to address the underlying gap? Validate zoning, target-LIF visibility and MPIO across both HA controllers and fabrics under a controlled takeover. Trace that host's WWPN zoning, igroup membership and LUN mapping before altering the storage object. Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. ExplanationCorrect Answer C:Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. Acceptance requires: Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window. Other Answers A:Validate zoning, target-LIF visibility and MPIO across both HA controllers and fabrics under a controlled takeover. This responds to another troubleshooting san solutions issue: An FC host loses storage during takeover although both controllers have target ports, and analysis finds no permitted path on the alternate fabric. Its mechanism is: HA gives storage ownership to the partner, but missing end-to-end paths prevent the host from using the newly serving controller. The present case instead requires: Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. B:Trace that host's WWPN zoning, igroup membership and LUN mapping before altering the storage object. This responds to another troubleshooting san solutions issue: A mapped FC LUN is missing from one host, but other hosts access it; administrators propose recreating the volume before checking zoning. Its mechanism is: LUN visibility relies on both fabric discovery and authorized initiator mapping; a healthy volume alone does not establish access. The present case instead requires: Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. D:Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. This responds to another troubleshooting san solutions issue: A database server uses two ONTAP FC paths but repeatedly chooses a nonoptimized ALUA path after a driver update. Its mechanism is: ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. The present case instead requires: Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity.
Question 314Host monitoring reports high I/O latency but the ONTAP controller's disk latency is low; one FC fabric also shows retransmits and congestion alarms. Which storage-system mechanism is the decisive factor in this situation? HA gives storage ownership to the partner, but missing end-to-end paths prevent the host from using the newly serving controller. LUN visibility relies on both fabric discovery and authorized initiator mapping; a healthy volume alone does not establish access. ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. ExplanationCorrect Answer D:Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. The corrective design is: Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. A relevant test is: Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window. Other Answers A:HA gives storage ownership to the partner, but missing end-to-end paths prevent the host from using the newly serving controller. That mechanism fits a different troubleshooting san solutions failure: An FC host loses storage during takeover although both controllers have target ports, and analysis finds no permitted path on the alternate fabric. Here the decisive mechanism is: Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. B:LUN visibility relies on both fabric discovery and authorized initiator mapping; a healthy volume alone does not establish access. That mechanism fits a different troubleshooting san solutions failure: A mapped FC LUN is missing from one host, but other hosts access it; administrators propose recreating the volume before checking zoning. Here the decisive mechanism is: Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. C:ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. That mechanism fits a different troubleshooting san solutions failure: A database server uses two ONTAP FC paths but repeatedly chooses a nonoptimized ALUA path after a driver update. Here the decisive mechanism is: Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone.
Question 315Host monitoring reports high I/O latency but the ONTAP controller's disk latency is low; one FC fabric also shows retransmits and congestion alarms. Which test would directly demonstrate that the required behavior now works? Perform a takeover simulation and verify the surviving optimized/available host paths are present in multipath output. Compare target WWPN discovery and igroup mappings for the failed host with a working reference host. Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window. Inspect path optimization states and verify the host prefers optimized paths while failover remains functional. ExplanationCorrect Answer C:Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window. This checks whether the remediation works: Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. The governing behavior is: Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. Other Answers A:Perform a takeover simulation and verify the surviving optimized/available host paths are present in multipath output. That check tests the separate condition: An FC host loses storage during takeover although both controllers have target ports, and analysis finds no permitted path on the alternate fabric. It would not establish the required result here: Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window. B:Compare target WWPN discovery and igroup mappings for the failed host with a working reference host. That check tests the separate condition: A mapped FC LUN is missing from one host, but other hosts access it; administrators propose recreating the volume before checking zoning. It would not establish the required result here: Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window. D:Inspect path optimization states and verify the host prefers optimized paths while failover remains functional. That check tests the separate condition: A database server uses two ONTAP FC paths but repeatedly chooses a nonoptimized ALUA path after a driver update. It would not establish the required result here: Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window.
Question 316Host monitoring reports high I/O latency but the ONTAP controller's disk latency is low; one FC fabric also shows retransmits and congestion alarms. What ongoing safeguard should be added to the ONTAP change process? Run periodic end-to-end HA and SAN path failover tests instead of fabric-only checks. Audit FC zoning and initiator membership following HBA replacement. Include SAN switch congestion/error telemetry in operational baselines. Test SAN host utility and multipath changes against supported ONTAP configurations. ExplanationCorrect Answer C:Include SAN switch congestion/error telemetry in operational baselines. This addresses the recurring cause: Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. It keeps the accepted correction in place: Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. Other Answers A:Run periodic end-to-end HA and SAN path failover tests instead of fabric-only checks. This safeguard targets a different repeat failure: An FC host loses storage during takeover although both controllers have target ports, and analysis finds no permitted path on the alternate fabric. For the present risk, the necessary control is: Include SAN switch congestion/error telemetry in operational baselines. B:Audit FC zoning and initiator membership following HBA replacement. This safeguard targets a different repeat failure: A mapped FC LUN is missing from one host, but other hosts access it; administrators propose recreating the volume before checking zoning. For the present risk, the necessary control is: Include SAN switch congestion/error telemetry in operational baselines. D:Test SAN host utility and multipath changes against supported ONTAP configurations. This safeguard targets a different repeat failure: A database server uses two ONTAP FC paths but repeatedly chooses a nonoptimized ALUA path after a driver update. For the present risk, the necessary control is: Include SAN switch congestion/error telemetry in operational baselines.
Question 317A database server uses two ONTAP FC paths but repeatedly chooses a nonoptimized ALUA path after a driver update. Which proposed action best resolves the specific issue without broadening access or risk? Limit excessive path exposure with supported zoning, portsets or SLM while retaining eligible redundant paths. Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. Validate zoning, target-LIF visibility and MPIO across both HA controllers and fabrics under a controlled takeover. Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. ExplanationCorrect Answer B:Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. Acceptance requires: Inspect path optimization states and verify the host prefers optimized paths while failover remains functional. Other Answers A:Limit excessive path exposure with supported zoning, portsets or SLM while retaining eligible redundant paths. This responds to another troubleshooting san solutions issue: A large SAN rollout creates more discovered target paths than the host supports and causes login instability on multiple servers. Its mechanism is: Unbounded target discovery can violate host multipath limits even if each individual link works. The present case instead requires: Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. C:Validate zoning, target-LIF visibility and MPIO across both HA controllers and fabrics under a controlled takeover. This responds to another troubleshooting san solutions issue: An FC host loses storage during takeover although both controllers have target ports, and analysis finds no permitted path on the alternate fabric. Its mechanism is: HA gives storage ownership to the partner, but missing end-to-end paths prevent the host from using the newly serving controller. The present case instead requires: Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. D:Correlate end-to-end host, fabric and array performance measurements before expanding aggregate capacity. This responds to another troubleshooting san solutions issue: Host monitoring reports high I/O latency but the ONTAP controller's disk latency is low; one FC fabric also shows retransmits and congestion alarms. Its mechanism is: Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. The present case instead requires: Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use.
Question 318A database server uses two ONTAP FC paths but repeatedly chooses a nonoptimized ALUA path after a driver update. Which ONTAP behavior explains why the original approach does not meet the requirement? ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. Unbounded target discovery can violate host multipath limits even if each individual link works. HA gives storage ownership to the partner, but missing end-to-end paths prevent the host from using the newly serving controller. Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. ExplanationCorrect Answer A:ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. The corrective design is: Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. A relevant test is: Inspect path optimization states and verify the host prefers optimized paths while failover remains functional. Other Answers B:Unbounded target discovery can violate host multipath limits even if each individual link works. That mechanism fits a different troubleshooting san solutions failure: A large SAN rollout creates more discovered target paths than the host supports and causes login instability on multiple servers. Here the decisive mechanism is: ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. C:HA gives storage ownership to the partner, but missing end-to-end paths prevent the host from using the newly serving controller. That mechanism fits a different troubleshooting san solutions failure: An FC host loses storage during takeover although both controllers have target ports, and analysis finds no permitted path on the alternate fabric. Here the decisive mechanism is: ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. D:Host I/O latency includes queueing and network/fabric delay; low disk latency shifts the investigation away from media capacity alone. That mechanism fits a different troubleshooting san solutions failure: Host monitoring reports high I/O latency but the ONTAP controller's disk latency is low; one FC fabric also shows retransmits and congestion alarms. Here the decisive mechanism is: ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O.
Question 319A database server uses two ONTAP FC paths but repeatedly chooses a nonoptimized ALUA path after a driver update. Which observation provides the strongest evidence that the issue was corrected? Enumerate host paths before and after scoping and check stable I/O under a single-path failure. Perform a takeover simulation and verify the surviving optimized/available host paths are present in multipath output. Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window. Inspect path optimization states and verify the host prefers optimized paths while failover remains functional. ExplanationCorrect Answer D:Inspect path optimization states and verify the host prefers optimized paths while failover remains functional. This checks whether the remediation works: Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. The governing behavior is: ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. Other Answers A:Enumerate host paths before and after scoping and check stable I/O under a single-path failure. That check tests the separate condition: A large SAN rollout creates more discovered target paths than the host supports and causes login instability on multiple servers. It would not establish the required result here: Inspect path optimization states and verify the host prefers optimized paths while failover remains functional. B:Perform a takeover simulation and verify the surviving optimized/available host paths are present in multipath output. That check tests the separate condition: An FC host loses storage during takeover although both controllers have target ports, and analysis finds no permitted path on the alternate fabric. It would not establish the required result here: Inspect path optimization states and verify the host prefers optimized paths while failover remains functional. C:Collect host MPIO path metrics, fabric counters and array latency for the same slow transaction window. That check tests the separate condition: Host monitoring reports high I/O latency but the ONTAP controller's disk latency is low; one FC fabric also shows retransmits and congestion alarms. It would not establish the required result here: Inspect path optimization states and verify the host prefers optimized paths while failover remains functional.
Question 320A database server uses two ONTAP FC paths but repeatedly chooses a nonoptimized ALUA path after a driver update. Which preventive practice most directly reduces recurrence of this failure? Test SAN host utility and multipath changes against supported ONTAP configurations. Enforce platform-specific maximum paths in SAN host standards. Run periodic end-to-end HA and SAN path failover tests instead of fabric-only checks. Include SAN switch congestion/error telemetry in operational baselines. ExplanationCorrect Answer A:Test SAN host utility and multipath changes against supported ONTAP configurations. This addresses the recurring cause: ALUA communicates optimized versus nonoptimized paths; host multipath selection determines which paths carry routine I/O. It keeps the accepted correction in place: Review the supported host utilities and ALUA/multipath selection policy to restore optimized path use. Other Answers B:Enforce platform-specific maximum paths in SAN host standards. This safeguard targets a different repeat failure: A large SAN rollout creates more discovered target paths than the host supports and causes login instability on multiple servers. For the present risk, the necessary control is: Test SAN host utility and multipath changes against supported ONTAP configurations. C:Run periodic end-to-end HA and SAN path failover tests instead of fabric-only checks. This safeguard targets a different repeat failure: An FC host loses storage during takeover although both controllers have target ports, and analysis finds no permitted path on the alternate fabric. For the present risk, the necessary control is: Test SAN host utility and multipath changes against supported ONTAP configurations. D:Include SAN switch congestion/error telemetry in operational baselines. This safeguard targets a different repeat failure: Host monitoring reports high I/O latency but the ONTAP controller's disk latency is low; one FC fabric also shows retransmits and congestion alarms. For the present risk, the necessary control is: Test SAN host utility and multipath changes against supported ONTAP configurations.