Question 320In a separate fictional JNCIS-SP lab review for Seabrook Metro 080, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: A customer service route never reaches another IS-IS area because the required export policy omits it. What is the direct residual network risk if the fault remains unresolved? An important customer service is unreachable outside its local PE. Some routers calculate stale paths and cannot reach required loopbacks. Duplicate identity creates conflicting LSPs and unstable route computation. Labeled packets are discarded at the affected core node. ExplanationCorrect Answer A:An important customer service is unreachable outside its local PE. Adjust the intended export policy match and confirm service-prefix advertisement. Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. Incorrect Answers B:Some routers calculate stale paths and cannot reach required loopbacks. This is applicable when a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset; the present condition is that a customer service route never reaches another IS-IS area because the required export policy omits it. C:Duplicate identity creates conflicting LSPs and unstable route computation. It is relevant if a device cloned from a lab template has the same IS-IS system ID as a production router, but the reported issue is that a customer service route never reaches another IS-IS area because the required export policy omits it. D:Labeled packets are discarded at the affected core node. This could help if an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing, but not when a customer service route never reaches another IS-IS area because the required export policy omits it.
Question 321At fictional Northpoint Access 081, a regional service-provider network, during a planned PE-to-core handoff, operations observes: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. Which targeted remediation best fits the reported behavior? Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. Correct area address design or the adjacency level according to the provider topology. Inspect the aggregate route contributors and align the summary with the intended component prefixes. ExplanationCorrect Answer A:Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. IS-IS levels separate routing scope and require a deliberate interlevel reachability design. An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. Incorrect Answers B:Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. That could help when a newly rebooted core router attracts transit traffic while its forwarding state is still being restored; here, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. C:Correct area address design or the adjacency level according to the provider topology. This is applicable when a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up; the present condition is that an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. D:Inspect the aggregate route contributors and align the summary with the intended component prefixes. It is relevant if a summary prefix is advertised even though operators have not confirmed which customer specifics contribute to it, but the reported issue is that an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change.
Question 322At fictional Northpoint Access 081, a regional service-provider network, during a planned PE-to-core handoff, operations observes: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. Why is this particular correction the best fit for the stated defect? IS-IS levels separate routing scope and require a deliberate interlevel reachability design. Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. IS-IS system IDs must uniquely represent participating routers in the routing domain. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. ExplanationCorrect Answer A:IS-IS levels separate routing scope and require a deliberate interlevel reachability design. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. Incorrect Answers B:Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. This could matter when a customer service route never reaches another IS-IS area because the required export policy omits it. In this case, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. C:IS-IS system IDs must uniquely represent participating routers in the routing domain. That could help when a device cloned from a lab template has the same IS-IS system ID as a production router; here, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. D:IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. This is applicable when a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation; the present condition is that an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change.
Question 323At fictional Northpoint Access 081, a regional service-provider network, during a planned PE-to-core handoff, operations observes: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. What direct observation would prove the corrective action worked? An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. All routers compute the expected cost and favor the intended transit route. The observed TLV maps to the expected reachability entry without false parser alarms. MAC learning and broadcast tests show separation of the two customers. ExplanationCorrect Answer A:An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. IS-IS levels separate routing scope and require a deliberate interlevel reachability design. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. Incorrect Answers B:All routers compute the expected cost and favor the intended transit route. It addresses a different problem: An intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. Here, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. C:The observed TLV maps to the expected reachability entry without false parser alarms. This could matter when a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. In this case, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. D:MAC learning and broadcast tests show separation of the two customers. That could help when two customer VLANs merge unexpectedly after a virtual-switch template is copied across separate services; here, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change.
Question 324At fictional Northpoint Access 081, a regional service-provider network, during a planned PE-to-core handoff, operations observes: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. Which failure consequence follows most closely from ignoring this issue? Operations declares recovery while customer packets use a degraded detour. Traffic between access area and core is silently blackholed. Unplanned DIS churn produces extra flooding and convergence disruption. A planned maintenance window causes an avoidable customer outage. ExplanationCorrect Answer B:Traffic between access area and core is silently blackholed. IS-IS levels separate routing scope and require a deliberate interlevel reachability design. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. Incorrect Answers A:Operations declares recovery while customer packets use a degraded detour. The choice would be appropriate if the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. Here, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. C:Unplanned DIS churn produces extra flooding and convergence disruption. It addresses a different problem: Operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment. Here, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. D:A planned maintenance window causes an avoidable customer outage. This could matter when a new MPLS LSP is provisioned and traffic is moved before its end-to-end reachability has been tested. In this case, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change.
Question 325In a separate fictional JNCIS-SP lab review for Linden Point 082, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. What intervention most directly restores the intended routing or switching behavior? Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. ExplanationCorrect Answer D:Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. IS-IS levels separate routing scope and require a deliberate interlevel reachability design. Incorrect Answers A:Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. This addresses a situation in which a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team; however, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. B:Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. The choice would be appropriate if a newly rebooted core router attracts transit traffic while its forwarding state is still being restored. Here, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. C:Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. That option concerns an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. The problem here is different: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change.
Question 326In a separate fictional JNCIS-SP lab review for Linden Point 082, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. Which networking principle explains why the proposed correction is appropriate? Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. IS-IS levels separate routing scope and require a deliberate interlevel reachability design. IS-IS routers need consistent flooded LSP information for reliable SPF results. OSPF shortest-path calculations rely on consistent synchronized link-state information within an area. ExplanationCorrect Answer B:IS-IS levels separate routing scope and require a deliberate interlevel reachability design. An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. Incorrect Answers A:Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. That relates to circumstances in which a customer service route never reaches another IS-IS area because the required export policy omits it. Here the problem is that an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. C:IS-IS routers need consistent flooded LSP information for reliable SPF results. The choice would be appropriate if a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset. Here, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. D:OSPF shortest-path calculations rely on consistent synchronized link-state information within an area. That option concerns two supposed adjacent routers have different views of a backbone link because database synchronization never completes. The problem here is different: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change.
Question 327In a separate fictional JNCIS-SP lab review for Linden Point 082, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. Which validation result would confirm the design is now functioning? The route table and forwarding lookup show the expected metric-driven next hop. The intended neighbor comes up under the approved authentication settings. A controlled packet trace follows the intended segment program under the chosen IGP topology. An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. ExplanationCorrect Answer D:An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. IS-IS levels separate routing scope and require a deliberate interlevel reachability design. Incorrect Answers A:The route table and forwarding lookup show the expected metric-driven next hop. It is useful for situations where the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change; the reported fault, though, is that an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. B:The intended neighbor comes up under the approved authentication settings. That relates to circumstances in which a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. Here the problem is that an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. C:A controlled packet trace follows the intended segment program under the chosen IGP topology. This addresses a situation in which a team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path; however, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change.
Question 328In a separate fictional JNCIS-SP lab review for Linden Point 082, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. What likely service impact does this condition create? Traffic between access area and core is silently blackholed. The partially initialized router drops transit packets during planned recovery. Operations declares recovery while customer packets use a degraded detour. Repeated flooding and customer frame loss continue despite healthy routes. ExplanationCorrect Answer A:Traffic between access area and core is silently blackholed. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. IS-IS levels separate routing scope and require a deliberate interlevel reachability design. Incorrect Answers B:The partially initialized router drops transit packets during planned recovery. It is useful for situations where a newly rebooted core router attracts transit traffic while its forwarding state is still being restored; the reported fault, though, is that an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. C:Operations declares recovery while customer packets use a degraded detour. That relates to circumstances in which the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. Here the problem is that an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. D:Repeated flooding and customer frame loss continue despite healthy routes. This addresses a situation in which a MAC moves rapidly among provider ports after a cabling change, yet troubleshooting focuses only on IP routing tables; however, an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change.
Question 329At fictional Harborview ISP 083, a regional service-provider network, during a two-site transit migration, operations observes: A newly rebooted core router attracts transit traffic while its forwarding state is still being restored. Which configuration or operational correction most directly addresses this failure? Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. Align the supported metric style and review full link metrics across the participating routing level. Inspect LSDB sequence and flooding state and repair the affected adjacency. Identify the ingress, transit, and egress LSR roles before modifying label rules. ExplanationCorrect Answer A:Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. The IS-IS overload indication can discourage transit use during control-plane recovery. Peer SPF paths avoid the router while overloaded and normal paths return after it is cleared. Incorrect Answers B:Align the supported metric style and review full link metrics across the participating routing level. This relates to a case where an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected; the current situation is that a newly rebooted core router attracts transit traffic while its forwarding state is still being restored. C:Inspect LSDB sequence and flooding state and repair the affected adjacency. It is useful for situations where a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset; the reported fault, though, is that a newly rebooted core router attracts transit traffic while its forwarding state is still being restored. D:Identify the ingress, transit, and egress LSR roles before modifying label rules. That relates to circumstances in which a network test expects the ingress PE to swap a label that it should actually impose. Here the problem is that a newly rebooted core router attracts transit traffic while its forwarding state is still being restored.
Question 330At fictional Harborview ISP 083, a regional service-provider network, during a two-site transit migration, operations observes: A newly rebooted core router attracts transit traffic while its forwarding state is still being restored. Which Junos forwarding or control-plane rule applies to this case? IS-IS hello PDUs discover and maintain neighbor relationships. The IS-IS overload indication can discourage transit use during control-plane recovery. IS-IS authentication parameters must match for participating routers to exchange protocol information. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. ExplanationCorrect Answer B:The IS-IS overload indication can discourage transit use during control-plane recovery. Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. Peer SPF paths avoid the router while overloaded and normal paths return after it is cleared. Incorrect Answers A:IS-IS hello PDUs discover and maintain neighbor relationships. It is relevant if an IS-IS neighbor remains down after an interface template disables its hello transmission, but the reported issue is that a newly rebooted core router attracts transit traffic while its forwarding state is still being restored. C:IS-IS authentication parameters must match for participating routers to exchange protocol information. This relates to a case where a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end; the current situation is that a newly rebooted core router attracts transit traffic while its forwarding state is still being restored. D:Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. It is useful for situations where an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; the reported fault, though, is that a newly rebooted core router attracts transit traffic while its forwarding state is still being restored.