Question 300At fictional Glenwood Connectivity 075, a regional service-provider network, during a preproduction design validation, operations observes: A monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. Which operational harm would persist without the intended correction? The partially initialized router drops transit packets during planned recovery. The backbone link stays out of the routing topology or an unsafe bypass is introduced. Operators suppress genuine incidents after repeated false IS-IS alerts. An unnoticed bridging loop can trigger widespread broadcast storms. ExplanationCorrect Answer C:Operators suppress genuine incidents after repeated false IS-IS alerts. IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. Incorrect Answers A:The partially initialized router drops transit packets during planned recovery. The choice would be appropriate if a newly rebooted core router attracts transit traffic while its forwarding state is still being restored. Here, a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. B:The backbone link stays out of the routing topology or an unsafe bypass is introduced. That option concerns a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. The problem here is different: A monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. D:An unnoticed bridging loop can trigger widespread broadcast storms. This could matter when a switch port connecting another bridge is incorrectly marked as an edge port, weakening normal loop-avoidance behavior. In this case, a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team.
Question 301In a separate fictional JNCIS-SP lab review for Hillside Transit 076, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. What should the Junos specialist change first to resolve this specific fault? Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. Ensure that the GRE outer endpoint resolves through the physical underlay instead of through the tunnel itself. ExplanationCorrect Answer A:Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. The observed TLV maps to the expected reachability entry without false parser alarms. IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. Incorrect Answers B:Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. The choice would be appropriate if the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. Here, a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. C:Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. That option concerns a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. The problem here is different: A monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. D:Ensure that the GRE outer endpoint resolves through the physical underlay instead of through the tunnel itself. It addresses a different problem: A route to a GRE destination is learned through the same tunnel, creating recursive or looping resolution. Here, a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team.
Question 302In a separate fictional JNCIS-SP lab review for Hillside Transit 076, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. What technical principle underlies the right remedy? The IS-IS overload indication can discourage transit use during control-plane recovery. Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. IPv6 forwarding requires a usable route and resolvable next hop in the correct address family. ExplanationCorrect Answer C:IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. The observed TLV maps to the expected reachability entry without false parser alarms. Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. Incorrect Answers A:The IS-IS overload indication can discourage transit use during control-plane recovery. That relates to circumstances in which a newly rebooted core router attracts transit traffic while its forwarding state is still being restored. Here the problem is that a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. B:Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. This addresses a situation in which a customer service route never reaches another IS-IS area because the required export policy omits it; however, a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. D:IPv6 forwarding requires a usable route and resolvable next hop in the correct address family. That option concerns an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. The problem here is different: A monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team.
Question 303In a separate fictional JNCIS-SP lab review for Hillside Transit 076, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. Which acceptance finding demonstrates the affected service has recovered? The observed TLV maps to the expected reachability entry without false parser alarms. The remote LSDB includes the fresh LSP and the loopback route becomes active. Peer SPF paths avoid the router while overloaded and normal paths return after it is cleared. The LDP neighbor is operational and exchanges label mappings for expected FECs. ExplanationCorrect Answer A:The observed TLV maps to the expected reachability entry without false parser alarms. Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. Incorrect Answers B:The remote LSDB includes the fresh LSP and the loopback route becomes active. That relates to circumstances in which a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset. Here the problem is that a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. C:Peer SPF paths avoid the router while overloaded and normal paths return after it is cleared. This addresses a situation in which a newly rebooted core router attracts transit traffic while its forwarding state is still being restored; however, a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. D:The LDP neighbor is operational and exchanges label mappings for expected FECs. The choice would be appropriate if two core routers cannot form an LDP session even though they discover one another on the connected link. Here, a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team.
Question 304In a separate fictional JNCIS-SP lab review for Hillside Transit 076, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. What is the direct residual network risk if the fault remains unresolved? Operators suppress genuine incidents after repeated false IS-IS alerts. Intra-area routes never propagate between connected devices. Duplicate identity creates conflicting LSPs and unstable route computation. A redundant Layer 2 link becomes a forwarding loop and floods the provider network. ExplanationCorrect Answer A:Operators suppress genuine incidents after repeated false IS-IS alerts. Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. Incorrect Answers B:Intra-area routes never propagate between connected devices. It is useful for situations where a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up; the reported fault, though, is that a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. C:Duplicate identity creates conflicting LSPs and unstable route computation. That relates to circumstances in which a device cloned from a lab template has the same IS-IS system ID as a production router. Here the problem is that a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. D:A redundant Layer 2 link becomes a forwarding loop and floods the provider network. This addresses a situation in which a blocked redundant link unexpectedly starts forwarding when BPDUs cease on a faulty remote bridge; however, a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team.
Question 305At fictional Westbridge Exchange 077, a regional service-provider network, during a core-routing acceptance test, operations observes: An intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. Which targeted remediation best fits the reported behavior? Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. Adjust the intended export policy match and confirm service-prefix advertisement. Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. Align the supported metric style and review full link metrics across the participating routing level. ExplanationCorrect Answer D:Align the supported metric style and review full link metrics across the participating routing level. IS-IS path calculations depend on compatible advertisements of link metrics. All routers compute the expected cost and favor the intended transit route. Incorrect Answers A:Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. This could help if a newly rebooted core router attracts transit traffic while its forwarding state is still being restored, but not when an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. B:Adjust the intended export policy match and confirm service-prefix advertisement. This relates to a case where a customer service route never reaches another IS-IS area because the required export policy omits it; the current situation is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. C:Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. It is useful for situations where a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets; the reported fault, though, is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected.
Question 306At fictional Westbridge Exchange 077, a regional service-provider network, during a core-routing acceptance test, operations observes: An intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. Why is this particular correction the best fit for the stated defect? The IS-IS overload indication can discourage transit use during control-plane recovery. IS-IS path calculations depend on compatible advertisements of link metrics. IS-IS elects a designated intermediate system on broadcast networks to manage pseudonode representation. IPv4 and IPv6 route lookups use separate address-family tables. ExplanationCorrect Answer B:IS-IS path calculations depend on compatible advertisements of link metrics. Align the supported metric style and review full link metrics across the participating routing level. All routers compute the expected cost and favor the intended transit route. Incorrect Answers A:The IS-IS overload indication can discourage transit use during control-plane recovery. It is relevant if a newly rebooted core router attracts transit traffic while its forwarding state is still being restored, but the reported issue is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. C:IS-IS elects a designated intermediate system on broadcast networks to manage pseudonode representation. This relates to a case where operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment; the current situation is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. D:IPv4 and IPv6 route lookups use separate address-family tables. It is useful for situations where a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised; the reported fault, though, is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected.
Question 307At fictional Westbridge Exchange 077, a regional service-provider network, during a core-routing acceptance test, operations observes: An intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. What direct observation would prove the corrective action worked? All routers compute the expected cost and favor the intended transit route. The route table and forwarding lookup show the expected metric-driven next hop. Operational output identifies the intended DIS and a stable pseudonode LSP. The lookup for the test destination selects the legitimate more-specific route rather than the broader summary. ExplanationCorrect Answer A:All routers compute the expected cost and favor the intended transit route. IS-IS path calculations depend on compatible advertisements of link metrics. Align the supported metric style and review full link metrics across the participating routing level. Incorrect Answers B:The route table and forwarding lookup show the expected metric-driven next hop. It is relevant if the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change, but the reported issue is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. C:Operational output identifies the intended DIS and a stable pseudonode LSP. This could help if operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment, but not when an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. D:The lookup for the test destination selects the legitimate more-specific route rather than the broader summary. This relates to a case where an operator changes route preference to make a broader prefix override a healthy more-specific prefix; the current situation is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected.
Question 308At fictional Westbridge Exchange 077, a regional service-provider network, during a core-routing acceptance test, operations observes: An intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. Which failure consequence follows most closely from ignoring this issue? An important customer service is unreachable outside its local PE. Unplanned DIS churn produces extra flooding and convergence disruption. Traffic unexpectedly overloads a low-capacity link. MPLS traffic remains broken despite restored IGP neighbors. ExplanationCorrect Answer C:Traffic unexpectedly overloads a low-capacity link. IS-IS path calculations depend on compatible advertisements of link metrics. Align the supported metric style and review full link metrics across the participating routing level. Incorrect Answers A:An important customer service is unreachable outside its local PE. That could help when a customer service route never reaches another IS-IS area because the required export policy omits it; here, an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. B:Unplanned DIS churn produces extra flooding and convergence disruption. This is applicable when operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment; the present condition is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. D:MPLS traffic remains broken despite restored IGP neighbors. This could help if after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device, but not when an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected.
Question 309In a separate fictional JNCIS-SP lab review for Crestland Networks 078, a carrier-edge and core routing team, following a monitored network change window, engineers find: An intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. What intervention most directly restores the intended routing or switching behavior? Assign a unique network entity title system identifier and verify database identities. Align the supported metric style and review full link metrics across the participating routing level. Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. Constrain permitted VLAN membership and confirm unauthorized tag handling. ExplanationCorrect Answer B:Align the supported metric style and review full link metrics across the participating routing level. All routers compute the expected cost and favor the intended transit route. IS-IS path calculations depend on compatible advertisements of link metrics. Incorrect Answers A:Assign a unique network entity title system identifier and verify database identities. This could matter when a device cloned from a lab template has the same IS-IS system ID as a production router. In this case, an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. C:Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. This is applicable when a newly rebooted core router attracts transit traffic while its forwarding state is still being restored; the present condition is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. D:Constrain permitted VLAN membership and confirm unauthorized tag handling. It is relevant if an interface permits every customer VLAN tag despite a contract listing only two approved VLANs, but the reported issue is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected.
Question 310In a separate fictional JNCIS-SP lab review for Crestland Networks 078, a carrier-edge and core routing team, following a monitored network change window, engineers find: An intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. Which networking principle explains why the proposed correction is appropriate? IS-IS path calculations depend on compatible advertisements of link metrics. A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. IS-IS routers need consistent flooded LSP information for reliable SPF results. BGP depends on working IP transport to establish its TCP session. ExplanationCorrect Answer A:IS-IS path calculations depend on compatible advertisements of link metrics. All routers compute the expected cost and favor the intended transit route. Align the supported metric style and review full link metrics across the participating routing level. Incorrect Answers B:A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. This could matter when the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. In this case, an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. C:IS-IS routers need consistent flooded LSP information for reliable SPF results. That could help when a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset; here, an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. D:BGP depends on working IP transport to establish its TCP session. This is applicable when a BGP peer has a correct AS number but cannot connect because its TCP transport address is unreachable; the present condition is that an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected.