Question 340At fictional Fairhaven Broadband 085, a regional service-provider network, during a preproduction design validation, operations observes: A provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. Which failure consequence follows most closely from ignoring this issue? Operators suppress genuine incidents after repeated false IS-IS alerts. The partially initialized router drops transit packets during planned recovery. The backbone link stays out of the routing topology or an unsafe bypass is introduced. A single member fault causes a complete customer circuit outage. ExplanationCorrect Answer C:The backbone link stays out of the routing topology or an unsafe bypass is introduced. IS-IS authentication parameters must match for participating routers to exchange protocol information. Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. Incorrect Answers A:Operators suppress genuine incidents after repeated false IS-IS alerts. This relates to a case where a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team; the current situation is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. B:The partially initialized router drops transit packets during planned recovery. It is useful for situations where a newly rebooted core router attracts transit traffic while its forwarding state is still being restored; the reported fault, though, is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. D:A single member fault causes a complete customer circuit outage. This addresses a situation in which a provider assumes a two-member LAG is redundant but has never checked forwarding when one member fails; however, a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end.
Question 341In a separate fictional JNCIS-SP lab review for Cedarwater Transit 086, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. What intervention most directly restores the intended routing or switching behavior? Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. Identify the ingress, transit, and egress LSR roles before modifying label rules. Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. ExplanationCorrect Answer D:Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. The intended neighbor comes up under the approved authentication settings. IS-IS authentication parameters must match for participating routers to exchange protocol information. Incorrect Answers A:Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. This could help if the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change, but not when a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. B:Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. This relates to a case where an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled; the current situation is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. C:Identify the ingress, transit, and egress LSR roles before modifying label rules. It is useful for situations where a network test expects the ingress PE to swap a label that it should actually impose; the reported fault, though, is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end.
Question 342In a separate fictional JNCIS-SP lab review for Cedarwater Transit 086, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. Which networking principle explains why the proposed correction is appropriate? IS-IS authentication parameters must match for participating routers to exchange protocol information. IS-IS routers need consistent flooded LSP information for reliable SPF results. Level 1 IS-IS requires appropriate area compatibility between neighbors. BGP address-family negotiation determines which network-layer reachability data can be exchanged. ExplanationCorrect Answer A:IS-IS authentication parameters must match for participating routers to exchange protocol information. The intended neighbor comes up under the approved authentication settings. Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. Incorrect Answers B:IS-IS routers need consistent flooded LSP information for reliable SPF results. This could help if a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset, but not when a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. C:Level 1 IS-IS requires appropriate area compatibility between neighbors. This relates to a case where a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up; the current situation is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. D:BGP address-family negotiation determines which network-layer reachability data can be exchanged. It is useful for situations where an IPv6 BGP session establishes at TCP level but does not exchange IPv6 reachability because the address family was not enabled; the reported fault, though, is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end.
Question 343In a separate fictional JNCIS-SP lab review for Cedarwater Transit 086, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. Which validation result would confirm the design is now functioning? The intended neighbor comes up under the approved authentication settings. Operational output identifies the intended DIS and a stable pseudonode LSP. The adjacency comes up at the planned level and routing information is exchanged correctly. Forwarding tables and controlled trace results agree with documented TTL behavior. ExplanationCorrect Answer A:The intended neighbor comes up under the approved authentication settings. Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. IS-IS authentication parameters must match for participating routers to exchange protocol information. Incorrect Answers B:Operational output identifies the intended DIS and a stable pseudonode LSP. It is relevant if operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment, but the reported issue is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. C:The adjacency comes up at the planned level and routing information is exchanged correctly. This could help if two adjacent core routers cannot establish IS-IS because one is configured only for Level 1 and the other only for Level 2, but not when a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. D:Forwarding tables and controlled trace results agree with documented TTL behavior. This relates to a case where traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut; the current situation is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end.
Question 344In a separate fictional JNCIS-SP lab review for Cedarwater Transit 086, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. What likely service impact does this condition create? The backbone link stays out of the routing topology or an unsafe bypass is introduced. Some routers calculate stale paths and cannot reach required loopbacks. The partially initialized router drops transit packets during planned recovery. Packets cannot reach the intended next hop despite a syntactically valid address. ExplanationCorrect Answer A:The backbone link stays out of the routing topology or an unsafe bypass is introduced. Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. IS-IS authentication parameters must match for participating routers to exchange protocol information. Incorrect Answers B:Some routers calculate stale paths and cannot reach required loopbacks. This is applicable when a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset; the present condition is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. C:The partially initialized router drops transit packets during planned recovery. It is relevant if a newly rebooted core router attracts transit traffic while its forwarding state is still being restored, but the reported issue is that a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. D:Packets cannot reach the intended next hop despite a syntactically valid address. This could help if an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design, but not when a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end.
Question 345At fictional Riverstone Networks 087, a regional service-provider network, during a core-routing acceptance test, operations observes: The IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. Which configuration or operational correction most directly addresses this failure? Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. Adjust the intended export policy match and confirm service-prefix advertisement. Restore IS-IS operation and appropriate hello behavior on the intended transit interface. Update the tunnel endpoint and restore underlying IP reachability before testing overlay traffic. ExplanationCorrect Answer A:Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. The route table and forwarding lookup show the expected metric-driven next hop. Incorrect Answers B:Adjust the intended export policy match and confirm service-prefix advertisement. That could help when a customer service route never reaches another IS-IS area because the required export policy omits it; here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. C:Restore IS-IS operation and appropriate hello behavior on the intended transit interface. This is applicable when an IS-IS neighbor remains down after an interface template disables its hello transmission; the present condition is that the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. D:Update the tunnel endpoint and restore underlying IP reachability before testing overlay traffic. It is relevant if a configured GRE tunnel stays unusable after the remote outer IP endpoint changes, but the reported issue is that the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change.
Question 346At fictional Riverstone Networks 087, a regional service-provider network, during a core-routing acceptance test, operations observes: The IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. Which Junos forwarding or control-plane rule applies to this case? IS-IS levels separate routing scope and require a deliberate interlevel reachability design. IS-IS system IDs must uniquely represent participating routers in the routing domain. IPv4 and IPv6 route lookups use separate address-family tables. A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. ExplanationCorrect Answer D:A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. The route table and forwarding lookup show the expected metric-driven next hop. Incorrect Answers A:IS-IS levels separate routing scope and require a deliberate interlevel reachability design. It addresses a different problem: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. Here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. B:IS-IS system IDs must uniquely represent participating routers in the routing domain. This could matter when a device cloned from a lab template has the same IS-IS system ID as a production router. In this case, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. C:IPv4 and IPv6 route lookups use separate address-family tables. That could help when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised; here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change.
Question 347At fictional Riverstone Networks 087, a regional service-provider network, during a core-routing acceptance test, operations observes: The IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. What operational evidence best establishes successful remediation? The route table and forwarding lookup show the expected metric-driven next hop. The remote LSDB includes the fresh LSP and the loopback route becomes active. The service route is visible on remote devices while unrelated prefixes remain suppressed. The affected switches show the same region digest and expected per-instance port roles. ExplanationCorrect Answer A:The route table and forwarding lookup show the expected metric-driven next hop. A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. Incorrect Answers B:The remote LSDB includes the fresh LSP and the loopback route becomes active. It addresses a different problem: A remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset. Here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. C:The service route is visible on remote devices while unrelated prefixes remain suppressed. This could matter when a customer service route never reaches another IS-IS area because the required export policy omits it. In this case, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. D:The affected switches show the same region digest and expected per-instance port roles. That could help when two interconnected switches place the same VLAN in different MSTP instances, leading to inconsistent blocking behavior; here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change.
Question 348At fictional Riverstone Networks 087, a regional service-provider network, during a core-routing acceptance test, operations observes: The IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. Which operational harm would persist without the intended correction? Duplicate identity creates conflicting LSPs and unstable route computation. Operations declares recovery while customer packets use a degraded detour. Traffic between access area and core is silently blackholed. Unwanted routes may alter forwarding or create customer traffic leakage. ExplanationCorrect Answer B:Operations declares recovery while customer packets use a degraded detour. A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. Incorrect Answers A:Duplicate identity creates conflicting LSPs and unstable route computation. The choice would be appropriate if a device cloned from a lab template has the same IS-IS system ID as a production router. Here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. C:Traffic between access area and core is silently blackholed. It addresses a different problem: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. Here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. D:Unwanted routes may alter forwarding or create customer traffic leakage. This could matter when a provider receives a customer-only prefix from a transit peer that should be blocked by an import policy. In this case, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change.
Question 349In a separate fictional JNCIS-SP lab review for Windmere Fiber 088, a carrier-edge and core routing team, following a monitored network change window, engineers find: The IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. What should the Junos specialist change first to resolve this specific fault? Align the intended IS-IS level capability for the shared link and inspect resulting adjacency. Assign a unique network entity title system identifier and verify database identities. Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. ExplanationCorrect Answer C:Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. The route table and forwarding lookup show the expected metric-driven next hop. A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. Incorrect Answers A:Align the intended IS-IS level capability for the shared link and inspect resulting adjacency. This addresses a situation in which two adjacent core routers cannot establish IS-IS because one is configured only for Level 1 and the other only for Level 2; however, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. B:Assign a unique network entity title system identifier and verify database identities. The choice would be appropriate if a device cloned from a lab template has the same IS-IS system ID as a production router. Here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. D:Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. It addresses a different problem: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change.
Question 350In a separate fictional JNCIS-SP lab review for Windmere Fiber 088, a carrier-edge and core routing team, following a monitored network change window, engineers find: The IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. What technical principle underlies the right remedy? IS-IS elects a designated intermediate system on broadcast networks to manage pseudonode representation. IS-IS routers need consistent flooded LSP information for reliable SPF results. BGP import policy governs which learned prefixes enter local route selection. A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. ExplanationCorrect Answer D:A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. The route table and forwarding lookup show the expected metric-driven next hop. Inspect LSDB entries, SPF route selection, and forwarding next hops instead of relying on neighbor state alone. Incorrect Answers A:IS-IS elects a designated intermediate system on broadcast networks to manage pseudonode representation. That relates to circumstances in which operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment. Here the problem is that the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. B:IS-IS routers need consistent flooded LSP information for reliable SPF results. This addresses a situation in which a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset; however, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change. C:BGP import policy governs which learned prefixes enter local route selection. The choice would be appropriate if a provider receives a customer-only prefix from a transit peer that should be blocked by an import policy. Here, the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change.