Question 260At fictional Bluehaven Backbone 065, a regional service-provider network, during a preproduction design validation, operations observes: A device cloned from a lab template has the same IS-IS system ID as a production router. Which failure consequence follows most closely from ignoring this issue? An important customer service is unreachable outside its local PE. IPv6 traffic fails although the IPv4 IS-IS topology is healthy. A single gateway device fault disconnects all hosts on the VLAN. Duplicate identity creates conflicting LSPs and unstable route computation. ExplanationCorrect Answer D:Duplicate identity creates conflicting LSPs and unstable route computation. IS-IS system IDs must uniquely represent participating routers in the routing domain. Assign a unique network entity title system identifier and verify database identities. Incorrect Answers A:An important customer service is unreachable outside its local PE. That could help when a customer service route never reaches another IS-IS area because the required export policy omits it; here, a device cloned from a lab template has the same IS-IS system ID as a production router. B:IPv6 traffic fails although the IPv4 IS-IS topology is healthy. This is applicable when an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled; the present condition is that a device cloned from a lab template has the same IS-IS system ID as a production router. C:A single gateway device fault disconnects all hosts on the VLAN. It is relevant if an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect, but the reported issue is that a device cloned from a lab template has the same IS-IS system ID as a production router.
Question 261In a separate fictional JNCIS-SP lab review for Lakewood Carrier 066, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A device cloned from a lab template has the same IS-IS system ID as a production router. What intervention most directly restores the intended routing or switching behavior? Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. Fix the peer export policy match for the authorized prefix and verify the announced routes. Assign a unique network entity title system identifier and verify database identities. ExplanationCorrect Answer D:Assign a unique network entity title system identifier and verify database identities. The LSDB lists separate stable system IDs for the two routers. IS-IS system IDs must uniquely represent participating routers in the routing domain. Incorrect Answers A:Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. This could matter when an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. In this case, a device cloned from a lab template has the same IS-IS system ID as a production router. B:Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. That could help when a newly rebooted core router attracts transit traffic while its forwarding state is still being restored; here, a device cloned from a lab template has the same IS-IS system ID as a production router. C:Fix the peer export policy match for the authorized prefix and verify the announced routes. This is applicable when a customer prefix is not advertised to an upstream peer because the outbound routing policy does not permit it; the present condition is that a device cloned from a lab template has the same IS-IS system ID as a production router.
Question 262In a separate fictional JNCIS-SP lab review for Lakewood Carrier 066, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A device cloned from a lab template has the same IS-IS system ID as a production router. Which networking principle explains why the proposed correction is appropriate? IS-IS carries enabled address-family reachability through appropriate protocol information. IS-IS path calculations depend on compatible advertisements of link metrics. IS-IS system IDs must uniquely represent participating routers in the routing domain. BGP multiprotocol families and matching policy control IPv6 route exchange. ExplanationCorrect Answer C:IS-IS system IDs must uniquely represent participating routers in the routing domain. The LSDB lists separate stable system IDs for the two routers. Assign a unique network entity title system identifier and verify database identities. Incorrect Answers A:IS-IS carries enabled address-family reachability through appropriate protocol information. It addresses a different problem: An IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. Here, a device cloned from a lab template has the same IS-IS system ID as a production router. B:IS-IS path calculations depend on compatible advertisements of link metrics. This could matter when an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected. In this case, a device cloned from a lab template has the same IS-IS system ID as a production router. D:BGP multiprotocol families and matching policy control IPv6 route exchange. This is applicable when an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter; the present condition is that a device cloned from a lab template has the same IS-IS system ID as a production router.
Question 263In a separate fictional JNCIS-SP lab review for Lakewood Carrier 066, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A device cloned from a lab template has the same IS-IS system ID as a production router. Which validation result would confirm the design is now functioning? Operational output identifies the intended DIS and a stable pseudonode LSP. An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. The LSDB lists separate stable system IDs for the two routers. ExplanationCorrect Answer D:The LSDB lists separate stable system IDs for the two routers. Assign a unique network entity title system identifier and verify database identities. IS-IS system IDs must uniquely represent participating routers in the routing domain. Incorrect Answers A:Operational output identifies the intended DIS and a stable pseudonode LSP. That option concerns operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment. The problem here is different: A device cloned from a lab template has the same IS-IS system ID as a production router. B:An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. It addresses a different problem: An L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. Here, a device cloned from a lab template has the same IS-IS system ID as a production router. C:Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. This could matter when hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. In this case, a device cloned from a lab template has the same IS-IS system ID as a production router.
Question 264In a separate fictional JNCIS-SP lab review for Lakewood Carrier 066, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A device cloned from a lab template has the same IS-IS system ID as a production router. What likely service impact does this condition create? No adjacency forms, so link-state routes cannot traverse that link. Duplicate identity creates conflicting LSPs and unstable route computation. Unplanned DIS churn produces extra flooding and convergence disruption. A route loop or false path preference persists due to misdiagnosis. ExplanationCorrect Answer B:Duplicate identity creates conflicting LSPs and unstable route computation. Assign a unique network entity title system identifier and verify database identities. IS-IS system IDs must uniquely represent participating routers in the routing domain. Incorrect Answers A:No adjacency forms, so link-state routes cannot traverse that link. The choice would be appropriate if an IS-IS neighbor remains down after an interface template disables its hello transmission. Here, a device cloned from a lab template has the same IS-IS system ID as a production router. C:Unplanned DIS churn produces extra flooding and convergence disruption. It addresses a different problem: Operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment. Here, a device cloned from a lab template has the same IS-IS system ID as a production router. D:A route loop or false path preference persists due to misdiagnosis. This could matter when an engineer blames BGP route rejection on local preference while a route carries an unexpected autonomous-system path. In this case, a device cloned from a lab template has the same IS-IS system ID as a production router.
Question 265At fictional Summitfield Carrier 067, a regional service-provider network, during a core-routing acceptance test, operations observes: An IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. Which configuration or operational correction most directly addresses this failure? Assign a unique network entity title system identifier and verify database identities. Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. Create the appropriate IPv6 address-family policy matching the approved prefixes. ExplanationCorrect Answer C:Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. IS-IS carries enabled address-family reachability through appropriate protocol information. The remote router receives the expected IPv6 IS-IS route and can reach the service. Incorrect Answers A:Assign a unique network entity title system identifier and verify database identities. This addresses a situation in which a device cloned from a lab template has the same IS-IS system ID as a production router; however, an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. B:Use the supported IS-IS overload behavior during maintenance and remove it when forwarding readiness is verified. The choice would be appropriate if a newly rebooted core router attracts transit traffic while its forwarding state is still being restored. Here, an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. D:Create the appropriate IPv6 address-family policy matching the approved prefixes. It addresses a different problem: A prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. Here, an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled.
Question 266At fictional Summitfield Carrier 067, a regional service-provider network, during a core-routing acceptance test, operations observes: An IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. Which Junos forwarding or control-plane rule applies to this case? IS-IS system IDs must uniquely represent participating routers in the routing domain. IS-IS carries enabled address-family reachability through appropriate protocol information. IS-IS authentication parameters must match for participating routers to exchange protocol information. Bridge-table observations must be interpreted alongside actual physical and logical port membership. ExplanationCorrect Answer B:IS-IS carries enabled address-family reachability through appropriate protocol information. Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. The remote router receives the expected IPv6 IS-IS route and can reach the service. Incorrect Answers A:IS-IS system IDs must uniquely represent participating routers in the routing domain. That relates to circumstances in which a device cloned from a lab template has the same IS-IS system ID as a production router. Here the problem is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. C:IS-IS authentication parameters must match for participating routers to exchange protocol information. The choice would be appropriate if a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. Here, an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. D:Bridge-table observations must be interpreted alongside actual physical and logical port membership. That option concerns a MAC is learned on an unexpected aggregation interface following a customer circuit move. The problem here is different: An IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled.
Question 267At fictional Summitfield Carrier 067, a regional service-provider network, during a core-routing acceptance test, operations observes: An IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. What operational evidence best establishes successful remediation? The LSDB lists separate stable system IDs for the two routers. The remote router receives the expected IPv6 IS-IS route and can reach the service. Peer SPF paths avoid the router while overloaded and normal paths return after it is cleared. The target prefix SID resolves to the planned node and the corresponding SR LSP is active. ExplanationCorrect Answer B:The remote router receives the expected IPv6 IS-IS route and can reach the service. IS-IS carries enabled address-family reachability through appropriate protocol information. Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. Incorrect Answers A:The LSDB lists separate stable system IDs for the two routers. It is useful for situations where a device cloned from a lab template has the same IS-IS system ID as a production router; the reported fault, though, is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. C:Peer SPF paths avoid the router while overloaded and normal paths return after it is cleared. This addresses a situation in which a newly rebooted core router attracts transit traffic while its forwarding state is still being restored; however, an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. D:The target prefix SID resolves to the planned node and the corresponding SR LSP is active. The choice would be appropriate if a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. Here, an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled.
Question 268At fictional Summitfield Carrier 067, a regional service-provider network, during a core-routing acceptance test, operations observes: An IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. Which operational harm would persist without the intended correction? A provider domain becomes partitioned and service prefixes disappear. Intra-area routes never propagate between connected devices. IPv6 traffic fails although the IPv4 IS-IS topology is healthy. Routers compute incompatible paths and traffic loops or blackholes can result. ExplanationCorrect Answer C:IPv6 traffic fails although the IPv4 IS-IS topology is healthy. IS-IS carries enabled address-family reachability through appropriate protocol information. Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. Incorrect Answers A:A provider domain becomes partitioned and service prefixes disappear. This relates to a case where two adjacent core routers cannot establish IS-IS because one is configured only for Level 1 and the other only for Level 2; the current situation is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. B:Intra-area routes never propagate between connected devices. It is useful for situations where a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up; the reported fault, though, is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. D:Routers compute incompatible paths and traffic loops or blackholes can result. This addresses a situation in which two supposed adjacent routers have different views of a backbone link because database synchronization never completes; however, an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled.
Question 269In a separate fictional JNCIS-SP lab review for Brightstone Backbone 068, a carrier-edge and core routing team, following a monitored network change window, engineers find: An IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. What should the Junos specialist change first to resolve this specific fault? Align the intended IS-IS level capability for the shared link and inspect resulting adjacency. Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. ExplanationCorrect Answer B:Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. The remote router receives the expected IPv6 IS-IS route and can reach the service. IS-IS carries enabled address-family reachability through appropriate protocol information. Incorrect Answers A:Align the intended IS-IS level capability for the shared link and inspect resulting adjacency. This could help if two adjacent core routers cannot establish IS-IS because one is configured only for Level 1 and the other only for Level 2, but not when an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. C:Synchronize the approved IS-IS authentication configuration across peers and verify secure adjacency. It is useful for situations where a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end; the reported fault, though, is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. D:Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. That relates to circumstances in which an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. Here the problem is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled.
Question 270In a separate fictional JNCIS-SP lab review for Brightstone Backbone 068, a carrier-edge and core routing team, following a monitored network change window, engineers find: An IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. What technical principle underlies the right remedy? Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. IS-IS carries enabled address-family reachability through appropriate protocol information. IS-IS path calculations depend on compatible advertisements of link metrics. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. ExplanationCorrect Answer B:IS-IS carries enabled address-family reachability through appropriate protocol information. The remote router receives the expected IPv6 IS-IS route and can reach the service. Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. Incorrect Answers A:Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. It is relevant if a customer service route never reaches another IS-IS area because the required export policy omits it, but the reported issue is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. C:IS-IS path calculations depend on compatible advertisements of link metrics. This relates to a case where an intended core link metric is truncated by a mismatched metric-style design and fails to shift paths as expected; the current situation is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled. D:Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. It is useful for situations where an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; the reported fault, though, is that an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled.