Question 250At fictional Windmere Fiber 063, a regional service-provider network, during a two-site transit migration, operations observes: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. Which Junos forwarding or control-plane rule applies to this case? Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. IS-IS elects a designated intermediate system on broadcast networks to manage pseudonode representation. Level 1 IS-IS requires appropriate area compatibility between neighbors. Encapsulation adds frame overhead that must fit along the Layer 2 service path. ExplanationCorrect Answer C:Level 1 IS-IS requires appropriate area compatibility between neighbors. Correct area address design or the adjacency level according to the provider topology. The planned L1 adjacency forms and the corresponding area information is consistent. Incorrect Answers A:Route policy controls which eligible nonnative prefixes are intentionally originated into IS-IS. It addresses a different problem: A customer service route never reaches another IS-IS area because the required export policy omits it. Here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. B:IS-IS elects a designated intermediate system on broadcast networks to manage pseudonode representation. This could matter when operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment. In this case, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. D:Encapsulation adds frame overhead that must fit along the Layer 2 service path. This is applicable when a service-provider QinQ link carries small frames but drops customer frames when the extra VLAN header exceeds the link MTU; the present condition is that a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up.
Question 251At fictional Windmere Fiber 063, a regional service-provider network, during a two-site transit migration, operations observes: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. What operational evidence best establishes successful remediation? The planned L1 adjacency forms and the corresponding area information is consistent. The LSDB lists separate stable system IDs for the two routers. An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. The primary path stays selected normally and the backup is activated only when the primary is unavailable. ExplanationCorrect Answer A:The planned L1 adjacency forms and the corresponding area information is consistent. Level 1 IS-IS requires appropriate area compatibility between neighbors. Correct area address design or the adjacency level according to the provider topology. Incorrect Answers B:The LSDB lists separate stable system IDs for the two routers. It addresses a different problem: A device cloned from a lab template has the same IS-IS system ID as a production router. Here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. C:An L1 router installs the intended route toward the L1-L2 boundary and reaches test destinations. This could matter when an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. In this case, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. D:The primary path stays selected normally and the backup is activated only when the primary is unavailable. That could help when a fallback static route takes traffic away from a healthy primary connection because its route preference was set too low; here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up.
Question 252At fictional Windmere Fiber 063, a regional service-provider network, during a two-site transit migration, operations observes: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. Which operational harm would persist without the intended correction? A provider domain becomes partitioned and service prefixes disappear. Intra-area routes never propagate between connected devices. Unplanned DIS churn produces extra flooding and convergence disruption. Traffic leaks or becomes blackholed at the L2/L3 boundary. ExplanationCorrect Answer B:Intra-area routes never propagate between connected devices. Level 1 IS-IS requires appropriate area compatibility between neighbors. Correct area address design or the adjacency level according to the provider topology. Incorrect Answers A:A provider domain becomes partitioned and service prefixes disappear. The choice would be appropriate if two adjacent core routers cannot establish IS-IS because one is configured only for Level 1 and the other only for Level 2. Here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. C:Unplanned DIS churn produces extra flooding and convergence disruption. It addresses a different problem: Operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment. Here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. D:Traffic leaks or becomes blackholed at the L2/L3 boundary. This could matter when an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch. In this case, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up.
Question 253In a separate fictional JNCIS-SP lab review for Meadowcrest Telecom 064, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. What should the Junos specialist change first to resolve this specific fault? Correct area address design or the adjacency level according to the provider topology. Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. ExplanationCorrect Answer A:Correct area address design or the adjacency level according to the provider topology. The planned L1 adjacency forms and the corresponding area information is consistent. Level 1 IS-IS requires appropriate area compatibility between neighbors. Incorrect Answers B:Validate the TLV and its enabled reachability function against the deployed Junos and protocol family. The choice would be appropriate if a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. Here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. C:Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. That option concerns an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change. The problem here is different: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. D:Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. It addresses a different problem: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. Here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up.
Question 254In a separate fictional JNCIS-SP lab review for Meadowcrest Telecom 064, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. What technical principle underlies the right remedy? Level 1 IS-IS requires appropriate area compatibility between neighbors. IS-IS system IDs must uniquely represent participating routers in the routing domain. IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. Redistributing non-OSPF reachability into OSPF requires suitable export policy. ExplanationCorrect Answer A:Level 1 IS-IS requires appropriate area compatibility between neighbors. The planned L1 adjacency forms and the corresponding area information is consistent. Correct area address design or the adjacency level according to the provider topology. Incorrect Answers B:IS-IS system IDs must uniquely represent participating routers in the routing domain. This addresses a situation in which a device cloned from a lab template has the same IS-IS system ID as a production router; however, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. C:IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. The choice would be appropriate if a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. Here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. D:Redistributing non-OSPF reachability into OSPF requires suitable export policy. That option concerns a static service prefix is missing from OSPF because the export policy was attached but does not match it. The problem here is different: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up.
Question 255In a separate fictional JNCIS-SP lab review for Meadowcrest Telecom 064, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. Which acceptance finding demonstrates the affected service has recovered? The planned L1 adjacency forms and the corresponding area information is consistent. The intended neighbor comes up under the approved authentication settings. The observed TLV maps to the expected reachability entry without false parser alarms. The intended distribution bridge is root and access ports show expected roles. ExplanationCorrect Answer A:The planned L1 adjacency forms and the corresponding area information is consistent. Correct area address design or the adjacency level according to the provider topology. Level 1 IS-IS requires appropriate area compatibility between neighbors. Incorrect Answers B:The intended neighbor comes up under the approved authentication settings. That relates to circumstances in which a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. Here the problem is that a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. C:The observed TLV maps to the expected reachability entry without false parser alarms. This addresses a situation in which a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team; however, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. D:The intended distribution bridge is root and access ports show expected roles. The choice would be appropriate if a low-capacity access switch becomes STP root after a new bridge priority setting. Here, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up.
Question 256In a separate fictional JNCIS-SP lab review for Meadowcrest Telecom 064, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. What is the direct residual network risk if the fault remains unresolved? Intra-area routes never propagate between connected devices. The backbone link stays out of the routing topology or an unsafe bypass is introduced. A provider domain becomes partitioned and service prefixes disappear. Unnecessary filtering interrupts normal bridged service. ExplanationCorrect Answer A:Intra-area routes never propagate between connected devices. Correct area address design or the adjacency level according to the provider topology. Level 1 IS-IS requires appropriate area compatibility between neighbors. Incorrect Answers B:The backbone link stays out of the routing topology or an unsafe bypass is introduced. It is useful for situations where a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end; the reported fault, though, is that a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. C:A provider domain becomes partitioned and service prefixes disappear. That relates to circumstances in which two adjacent core routers cannot establish IS-IS because one is configured only for Level 1 and the other only for Level 2. Here the problem is that a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up. D:Unnecessary filtering interrupts normal bridged service. This addresses a situation in which a customer observes occasional unknown-unicast flooding after long inactivity and assumes every flood is a loop; however, a Level 1 IS-IS adjacency fails between routers with different area addresses even though the physical link is up.
Question 257At fictional Bluehaven Backbone 065, a regional service-provider network, during a preproduction design validation, operations observes: A device cloned from a lab template has the same IS-IS system ID as a production router. Which targeted remediation best fits the reported behavior? Assign a unique network entity title system identifier and verify database identities. Review DIS selection parameters and verify pseudonode origination for the LAN. Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. Use the approved source address and confirm matching outer-packet forwarding and policy. ExplanationCorrect Answer A:Assign a unique network entity title system identifier and verify database identities. IS-IS system IDs must uniquely represent participating routers in the routing domain. The LSDB lists separate stable system IDs for the two routers. Incorrect Answers B:Review DIS selection parameters and verify pseudonode origination for the LAN. This relates to a case where operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment; the current situation is that a device cloned from a lab template has the same IS-IS system ID as a production router. C:Restore suitable L1-L2 connectivity or the documented route-leaking/default behavior. It is useful for situations where an L1-only site lacks an approved route to reach destinations in the backbone after a level-transition change; the reported fault, though, is that a device cloned from a lab template has the same IS-IS system ID as a production router. D:Use the approved source address and confirm matching outer-packet forwarding and policy. That relates to circumstances in which a GRE tunnel appears operational in configuration but sources packets from an interface not permitted by the core ACL. Here the problem is that a device cloned from a lab template has the same IS-IS system ID as a production router.
Question 258At fictional Bluehaven Backbone 065, a regional service-provider network, during a preproduction design validation, operations observes: A device cloned from a lab template has the same IS-IS system ID as a production router. Why is this particular correction the best fit for the stated defect? The IS-IS overload indication can discourage transit use during control-plane recovery. IS-IS neighbors require compatible level participation to exchange link-state information. Junos directly connected reachability depends on active logical interface configuration and state. IS-IS system IDs must uniquely represent participating routers in the routing domain. ExplanationCorrect Answer D:IS-IS system IDs must uniquely represent participating routers in the routing domain. Assign a unique network entity title system identifier and verify database identities. The LSDB lists separate stable system IDs for the two routers. Incorrect Answers A:The IS-IS overload indication can discourage transit use during control-plane recovery. It is relevant if a newly rebooted core router attracts transit traffic while its forwarding state is still being restored, but the reported issue is that a device cloned from a lab template has the same IS-IS system ID as a production router. B:IS-IS neighbors require compatible level participation to exchange link-state information. This could help if two adjacent core routers cannot establish IS-IS because one is configured only for Level 1 and the other only for Level 2, but not when a device cloned from a lab template has the same IS-IS system ID as a production router. C:Junos directly connected reachability depends on active logical interface configuration and state. This relates to a case where a directly connected peering subnet disappears after a logical interface unit is removed during a maintenance template rollout; the current situation is that a device cloned from a lab template has the same IS-IS system ID as a production router.
Question 259At fictional Bluehaven Backbone 065, a regional service-provider network, during a preproduction design validation, operations observes: A device cloned from a lab template has the same IS-IS system ID as a production router. What direct observation would prove the corrective action worked? The service route is visible on remote devices while unrelated prefixes remain suppressed. The LSDB lists separate stable system IDs for the two routers. The adjacency comes up at the planned level and routing information is exchanged correctly. The port's intentional blocking reason and root path are verified in control-plane output. ExplanationCorrect Answer B:The LSDB lists separate stable system IDs for the two routers. IS-IS system IDs must uniquely represent participating routers in the routing domain. Assign a unique network entity title system identifier and verify database identities. Incorrect Answers A:The service route is visible on remote devices while unrelated prefixes remain suppressed. This is applicable when a customer service route never reaches another IS-IS area because the required export policy omits it; the present condition is that a device cloned from a lab template has the same IS-IS system ID as a production router. C:The adjacency comes up at the planned level and routing information is exchanged correctly. This could help if two adjacent core routers cannot establish IS-IS because one is configured only for Level 1 and the other only for Level 2, but not when a device cloned from a lab template has the same IS-IS system ID as a production router. D:The port's intentional blocking reason and root path are verified in control-plane output. This relates to a case where a link is physically up but stays blocked by spanning tree, and an operator incorrectly blames interface optics; the current situation is that a device cloned from a lab template has the same IS-IS system ID as a production router.
Question 260At fictional Bluehaven Backbone 065, a regional service-provider network, during a preproduction design validation, operations observes: A device cloned from a lab template has the same IS-IS system ID as a production router. Which failure consequence follows most closely from ignoring this issue? An important customer service is unreachable outside its local PE. IPv6 traffic fails although the IPv4 IS-IS topology is healthy. A single gateway device fault disconnects all hosts on the VLAN. Duplicate identity creates conflicting LSPs and unstable route computation. ExplanationCorrect Answer D:Duplicate identity creates conflicting LSPs and unstable route computation. IS-IS system IDs must uniquely represent participating routers in the routing domain. Assign a unique network entity title system identifier and verify database identities. Incorrect Answers A:An important customer service is unreachable outside its local PE. That could help when a customer service route never reaches another IS-IS area because the required export policy omits it; here, a device cloned from a lab template has the same IS-IS system ID as a production router. B:IPv6 traffic fails although the IPv4 IS-IS topology is healthy. This is applicable when an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled; the present condition is that a device cloned from a lab template has the same IS-IS system ID as a production router. C:A single gateway device fault disconnects all hosts on the VLAN. It is relevant if an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect, but the reported issue is that a device cloned from a lab template has the same IS-IS system ID as a production router.