Question 870In a separate fictional JNCIS-SP lab review for Brightstone Backbone 218, a carrier-edge and core routing team, following a monitored network change window, engineers find: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. Which networking principle explains why the proposed correction is appropriate? IPv4 and IPv6 route lookups use separate address-family tables. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. A prefix SID normally expresses reachability to a node or prefix along the underlying shortest path. ExplanationCorrect Answer A:IPv4 and IPv6 route lookups use separate address-family tables. The expected IPv6 route and active forwarding next hop are visible in inet6 output. Check the appropriate inet6 routing instance and forwarding state. Incorrect Answers B:Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. This could help if an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design, but not when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. C:IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. This relates to a case where a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation; the current situation is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. D:A prefix SID normally expresses reachability to a node or prefix along the underlying shortest path. It is useful for situations where a team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path; the reported fault, though, is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.
Question 871In a separate fictional JNCIS-SP lab review for Brightstone Backbone 218, a carrier-edge and core routing team, following a monitored network change window, engineers find: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. Which validation result would confirm the design is now functioning? The route resolves over the intended interface and IPv6 neighbor discovery succeeds. The expected IPv6 route and active forwarding next hop are visible in inet6 output. The authorized inet6 routes are accepted while prohibited IPv6 prefixes remain blocked. The target table contains the approved route while unrelated tenant tables remain unchanged. ExplanationCorrect Answer B:The expected IPv6 route and active forwarding next hop are visible in inet6 output. Check the appropriate inet6 routing instance and forwarding state. IPv4 and IPv6 route lookups use separate address-family tables. Incorrect Answers A:The route resolves over the intended interface and IPv6 neighbor discovery succeeds. This is applicable when an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; the present condition is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. C:The authorized inet6 routes are accepted while prohibited IPv6 prefixes remain blocked. This could help if a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish, but not when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. D:The target table contains the approved route while unrelated tenant tables remain unchanged. This relates to a case where a route intended for a monitoring routing table is missing because the RIB group does not include the recipient table; the current situation is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.
Question 872In a separate fictional JNCIS-SP lab review for Brightstone Backbone 218, a carrier-edge and core routing team, following a monitored network change window, engineers find: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. What likely service impact does this condition create? IPv6 routing does not converge across the link. IPv6 traffic is entirely lost due to an unsuitable policy match. A false no-route diagnosis delays the actual IPv6 repair. Traffic is briefly blackholed during normal network convergence. ExplanationCorrect Answer C:A false no-route diagnosis delays the actual IPv6 repair. Check the appropriate inet6 routing instance and forwarding state. IPv4 and IPv6 route lookups use separate address-family tables. Incorrect Answers A:IPv6 routing does not converge across the link. That could help when an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted; here, a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. B:IPv6 traffic is entirely lost due to an unsuitable policy match. This is applicable when a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish; the present condition is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. D:Traffic is briefly blackholed during normal network convergence. This could help if a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage, but not when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.
Question 873At fictional Eastbridge Networks 219, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. Which configuration or operational correction most directly addresses this failure? Associate the link-local next hop with the correct egress interface and validate neighbor resolution. Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables. Check the appropriate inet6 routing instance and forwarding state. Configure the appropriate BGP IPv6 family on the peers and confirm route exchange. ExplanationCorrect Answer A:Associate the link-local next hop with the correct egress interface and validate neighbor resolution. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. The route resolves over the intended interface and IPv6 neighbor discovery succeeds. Incorrect Answers B:Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables. That could help when an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface; here, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. C:Check the appropriate inet6 routing instance and forwarding state. This is applicable when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised; the present condition is that an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. D:Configure the appropriate BGP IPv6 family on the peers and confirm route exchange. It is relevant if an IPv6 BGP session establishes at TCP level but does not exchange IPv6 reachability because the address family was not enabled, but the reported issue is that an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design.
Question 874At fictional Eastbridge Networks 219, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. Which Junos forwarding or control-plane rule applies to this case? Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. IPv6 forwarding requires a usable route and resolvable next hop in the correct address family. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. Layer 2 bridges select egress ports using MAC/VLAN information before any routed-hop lookup. ExplanationCorrect Answer A:Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. Associate the link-local next hop with the correct egress interface and validate neighbor resolution. The route resolves over the intended interface and IPv6 neighbor discovery succeeds. Incorrect Answers B:IPv6 forwarding requires a usable route and resolvable next hop in the correct address family. This could matter when an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. In this case, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. C:IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. That could help when a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation; here, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. D:Layer 2 bridges select egress ports using MAC/VLAN information before any routed-hop lookup. This is applicable when an operator adds an IP route to fix traffic that never leaves a local bridge domain because its destination MAC is unknown; the present condition is that an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design.
Question 875At fictional Eastbridge Networks 219, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. What operational evidence best establishes successful remediation? Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. The route resolves over the intended interface and IPv6 neighbor discovery succeeds. The expected IPv6 route and active forwarding next hop are visible in inet6 output. The lookup for the test destination selects the legitimate more-specific route rather than the broader summary. ExplanationCorrect Answer B:The route resolves over the intended interface and IPv6 neighbor discovery succeeds. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. Associate the link-local next hop with the correct egress interface and validate neighbor resolution. Incorrect Answers A:Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. That option concerns an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. The problem here is different: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. C:The expected IPv6 route and active forwarding next hop are visible in inet6 output. This could matter when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. In this case, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. D:The lookup for the test destination selects the legitimate more-specific route rather than the broader summary. That could help when an operator changes route preference to make a broader prefix override a healthy more-specific prefix; here, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design.
Question 876At fictional Eastbridge Networks 219, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. Which operational harm would persist without the intended correction? IPv6 routing does not converge across the link. Dual-stack service is only partially operational. Sites in different areas cannot exchange business traffic reliably. Packets cannot reach the intended next hop despite a syntactically valid address. ExplanationCorrect Answer D:Packets cannot reach the intended next hop despite a syntactically valid address. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. Associate the link-local next hop with the correct egress interface and validate neighbor resolution. Incorrect Answers A:IPv6 routing does not converge across the link. The choice would be appropriate if an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Here, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. B:Dual-stack service is only partially operational. That option concerns a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. The problem here is different: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. C:Sites in different areas cannot exchange business traffic reliably. It addresses a different problem: A site advertises internal prefixes inside one area, but a remote OSPF area cannot learn them because the area border configuration is incomplete. Here, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design.
Question 877In a separate fictional JNCIS-SP lab review for Orchard Link 220, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. What should the Junos specialist change first to resolve this specific fault? Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. Associate the link-local next hop with the correct egress interface and validate neighbor resolution. Check the appropriate inet6 routing instance and forwarding state. Correct the filter-based forwarding action and confirm the classification matches only the approved traffic. ExplanationCorrect Answer B:Associate the link-local next hop with the correct egress interface and validate neighbor resolution. The route resolves over the intended interface and IPv6 neighbor discovery succeeds. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. Incorrect Answers A:Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. This addresses a situation in which an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared; however, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. C:Check the appropriate inet6 routing instance and forwarding state. That option concerns a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. The problem here is different: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. D:Correct the filter-based forwarding action and confirm the classification matches only the approved traffic. It addresses a different problem: A traffic class should be steered into an alternate routing instance but the firewall filter maps it to the default route lookup. Here, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design.
Question 878In a separate fictional JNCIS-SP lab review for Orchard Link 220, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. What technical principle underlies the right remedy? IPv6 forwarding requires a usable route and resolvable next hop in the correct address family. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. OSPFv3 carries IPv6 routing information and requires the relevant protocol context. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. ExplanationCorrect Answer B:Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. The route resolves over the intended interface and IPv6 neighbor discovery succeeds. Associate the link-local next hop with the correct egress interface and validate neighbor resolution. Incorrect Answers A:IPv6 forwarding requires a usable route and resolvable next hop in the correct address family. That relates to circumstances in which an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. Here the problem is that an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. C:OSPFv3 carries IPv6 routing information and requires the relevant protocol context. The choice would be appropriate if an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Here, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. D:On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. That option concerns on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure. The problem here is different: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design.
Question 879In a separate fictional JNCIS-SP lab review for Orchard Link 220, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. Which acceptance finding demonstrates the affected service has recovered? The inet6 route is active and a controlled IPv6 probe reaches the prefix. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. The route resolves over the intended interface and IPv6 neighbor discovery succeeds. The interface unit is operational and the connected subnet appears in the correct routing table. ExplanationCorrect Answer C:The route resolves over the intended interface and IPv6 neighbor discovery succeeds. Associate the link-local next hop with the correct egress interface and validate neighbor resolution. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. Incorrect Answers A:The inet6 route is active and a controlled IPv6 probe reaches the prefix. It is useful for situations where an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface; the reported fault, though, is that an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. B:OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. That relates to circumstances in which an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Here the problem is that an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. D:The interface unit is operational and the connected subnet appears in the correct routing table. The choice would be appropriate if a directly connected peering subnet disappears after a logical interface unit is removed during a maintenance template rollout. Here, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design.
Question 880In a separate fictional JNCIS-SP lab review for Orchard Link 220, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. What is the direct residual network risk if the fault remains unresolved? IPv6 service fails across a still-configured but unusable tunnel. IPv6 Internet service fails while IPv4 peering looks healthy. Packets cannot reach the intended next hop despite a syntactically valid address. Packets to the customer prefix are dropped despite the static route statement being present. ExplanationCorrect Answer C:Packets cannot reach the intended next hop despite a syntactically valid address. Associate the link-local next hop with the correct egress interface and validate neighbor resolution. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. Incorrect Answers A:IPv6 service fails across a still-configured but unusable tunnel. This relates to a case where an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared; the current situation is that an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. B:IPv6 Internet service fails while IPv4 peering looks healthy. It is useful for situations where an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter; the reported fault, though, is that an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. D:Packets to the customer prefix are dropped despite the static route statement being present. This addresses a situation in which a provider edge has a static route for a customer prefix, but its next hop resolves only through a disconnected interface; however, an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design.