McAfee Secured

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

100% Juniper JN0-364 Guaranteed Success With Testking Training Materials

Get Real JN0-364 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

69 Questions & Answers with Testing Engine

"Service Provider Routing and Switching, Specialist (JNCIS-SP) Exam", also known as JN0-364 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-364 Exam Engine. Your JN0-364 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 86

Question 850

At fictional Windmere Fiber 213, a regional service-provider network, during a two-site transit migration, operations observes: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. Why is this particular correction the best fit for the stated defect?

  1. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability.
  2. OSPFv3 carries IPv6 routing information and requires the relevant protocol context.
  3. IPv4 and IPv6 route lookups use separate address-family tables.
  4. A discard route can protect against loops for unallocated portions of an aggregate but must not mask actual reachability.

Explanation

Correct Answer

A:

IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes. Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end.

Incorrect Answers

B:

OSPFv3 carries IPv6 routing information and requires the relevant protocol context. This could matter when an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. In this case, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

C:

IPv4 and IPv6 route lookups use separate address-family tables. That could help when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised; here, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

D:

A discard route can protect against loops for unallocated portions of an aggregate but must not mask actual reachability. This is applicable when a provider adds a discard summary but accidentally makes it cover reachable customer addresses more specific routes have not yet advertised; the present condition is that a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

Question 851

At fictional Windmere Fiber 213, a regional service-provider network, during a two-site transit migration, operations observes: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. What direct observation would prove the corrective action worked?

  1. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix.
  2. The route resolves over the intended interface and IPv6 neighbor discovery succeeds.
  3. Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end.
  4. Both client sessions stabilize and expected reflected routes reach peers.

Explanation

Correct Answer

C:

Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes.

Incorrect Answers

A:

OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. That option concerns an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. The problem here is different: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

B:

The route resolves over the intended interface and IPv6 neighbor discovery succeeds. It addresses a different problem: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. Here, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

D:

Both client sessions stabilize and expected reflected routes reach peers. That could help when an internal client learns routes from another client only intermittently after the route-reflector peering address changes; here, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

Question 852

At fictional Windmere Fiber 213, a regional service-provider network, during a two-site transit migration, operations observes: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. Which failure consequence follows most closely from ignoring this issue?

  1. IPv6 traffic is entirely lost due to an unsuitable policy match.
  2. IPv6 Internet service fails while IPv4 peering looks healthy.
  3. Dual-stack service is only partially operational.
  4. Unwanted routes may alter forwarding or create customer traffic leakage.

Explanation

Correct Answer

C:

Dual-stack service is only partially operational. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes.

Incorrect Answers

A:

IPv6 traffic is entirely lost due to an unsuitable policy match. The choice would be appropriate if a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. Here, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

B:

IPv6 Internet service fails while IPv4 peering looks healthy. That option concerns an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter. The problem here is different: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

D:

Unwanted routes may alter forwarding or create customer traffic leakage. This could matter when a provider receives a customer-only prefix from a transit peer that should be blocked by an import policy. In this case, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

Question 853

In a separate fictional JNCIS-SP lab review for Meadowcrest Telecom 214, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. What intervention most directly restores the intended routing or switching behavior?

  1. Create the appropriate IPv6 address-family policy matching the approved prefixes.
  2. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state.
  3. Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes.
  4. Align the peer type and AS settings with the intended same-AS design.

Explanation

Correct Answer

C:

Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes. Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability.

Incorrect Answers

A:

Create the appropriate IPv6 address-family policy matching the approved prefixes. This addresses a situation in which a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish; however, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

B:

Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. The choice would be appropriate if an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Here, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

D:

Align the peer type and AS settings with the intended same-AS design. It addresses a different problem: An operator configures an internal route-reflector session as EBGP and introduces an unintended AS boundary. Here, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

Question 854

In a separate fictional JNCIS-SP lab review for Meadowcrest Telecom 214, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. Which networking principle explains why the proposed correction is appropriate?

  1. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context.
  2. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability.
  3. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic.
  4. IRB traffic must bridge and route within an intentionally consistent service context.

Explanation

Correct Answer

B:

IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end. Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes.

Incorrect Answers

A:

Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. That relates to circumstances in which an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. Here the problem is that a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

C:

IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. The choice would be appropriate if an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Here, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

D:

IRB traffic must bridge and route within an intentionally consistent service context. That option concerns an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch. The problem here is different: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

Question 855

In a separate fictional JNCIS-SP lab review for Meadowcrest Telecom 214, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. Which validation result would confirm the design is now functioning?

  1. The authorized IPv6 prefixes arrive in the intended inet6 table without IPv4 policy changes.
  2. Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed.
  3. The interswitch link uses normal RSTP role and state handling during topology tests.
  4. Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end.

Explanation

Correct Answer

D:

Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end. Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability.

Incorrect Answers

A:

The authorized IPv6 prefixes arrive in the intended inet6 table without IPv4 policy changes. It is useful for situations where an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter; the reported fault, though, is that a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

B:

Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. That relates to circumstances in which an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Here the problem is that a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

C:

The interswitch link uses normal RSTP role and state handling during topology tests. This addresses a situation in which a switch port connecting another bridge is incorrectly marked as an edge port, weakening normal loop-avoidance behavior; however, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

Question 856

In a separate fictional JNCIS-SP lab review for Meadowcrest Telecom 214, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. What likely service impact does this condition create?

  1. Dual-stack service is only partially operational.
  2. IPv6 service fails across a still-configured but unusable tunnel.
  3. IPv6 traffic is entirely lost due to an unsuitable policy match.
  4. Outbound traffic takes an expensive or congested transit link.

Explanation

Correct Answer

A:

Dual-stack service is only partially operational. Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability.

Incorrect Answers

B:

IPv6 service fails across a still-configured but unusable tunnel. It is useful for situations where an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared; the reported fault, though, is that a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

C:

IPv6 traffic is entirely lost due to an unsuitable policy match. That relates to circumstances in which a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. Here the problem is that a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

D:

Outbound traffic takes an expensive or congested transit link. This addresses a situation in which a customer AS should prefer a primary exit but its IBGP paths have the same local preference after a policy reset; however, a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation.

Question 857

At fictional Bluehaven Backbone 215, a regional service-provider network, during a preproduction design validation, operations observes: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Which configuration or operational correction most directly addresses this failure?

  1. Create the appropriate IPv6 address-family policy matching the approved prefixes.
  2. Associate the link-local next hop with the correct egress interface and validate neighbor resolution.
  3. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes.
  4. Assign planned bridge priorities and verify root and alternate port roles.

Explanation

Correct Answer

C:

Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed.

Incorrect Answers

A:

Create the appropriate IPv6 address-family policy matching the approved prefixes. This could help if a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish, but not when an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

B:

Associate the link-local next hop with the correct egress interface and validate neighbor resolution. This relates to a case where an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; the current situation is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

Assign planned bridge priorities and verify root and alternate port roles. That relates to circumstances in which a low-capacity access switch becomes STP root after a new bridge priority setting. Here the problem is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Question 858

At fictional Bluehaven Backbone 215, a regional service-provider network, during a preproduction design validation, operations observes: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Which Junos forwarding or control-plane rule applies to this case?

  1. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic.
  2. BGP multiprotocol families and matching policy control IPv6 route exchange.
  3. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context.
  4. Provider bridging can add an outer service VLAN tag while retaining customer VLAN identity.

Explanation

Correct Answer

A:

IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed.

Incorrect Answers

B:

BGP multiprotocol families and matching policy control IPv6 route exchange. This could help if an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter, but not when an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

C:

Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. This relates to a case where an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; the current situation is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

Provider bridging can add an outer service VLAN tag while retaining customer VLAN identity. It is useful for situations where provider bridging accidentally rewrites the subscriber VLAN tag when applying an outer service tag; the reported fault, though, is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Question 859

At fictional Bluehaven Backbone 215, a regional service-provider network, during a preproduction design validation, operations observes: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. What operational evidence best establishes successful remediation?

  1. The expected IPv6 route and active forwarding next hop are visible in inet6 output.
  2. The inet6 route is active and a controlled IPv6 probe reaches the prefix.
  3. Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed.
  4. Loss of one link leaves the logical bundle up and service traffic continues on the other.

Explanation

Correct Answer

C:

Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes.

Incorrect Answers

A:

The expected IPv6 route and active forwarding next hop are visible in inet6 output. This is applicable when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised; the present condition is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

B:

The inet6 route is active and a controlled IPv6 probe reaches the prefix. It is relevant if an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface, but the reported issue is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

Loss of one link leaves the logical bundle up and service traffic continues on the other. This relates to a case where a provider assumes a two-member LAG is redundant but has never checked forwarding when one member fails; the current situation is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Question 860

At fictional Bluehaven Backbone 215, a regional service-provider network, during a preproduction design validation, operations observes: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Which operational harm would persist without the intended correction?

  1. IPv6 service fails across a still-configured but unusable tunnel.
  2. IPv6 Internet service fails while IPv4 peering looks healthy.
  3. IPv6 customers lose service even when IPv4 routing remains healthy.
  4. Traffic engineering decisions depend on a route attribute outside its applicable selection scope.

Explanation

Correct Answer

A:

IPv6 service fails across a still-configured but unusable tunnel. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes.

Incorrect Answers

B:

IPv6 Internet service fails while IPv4 peering looks healthy. This is applicable when an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter; the present condition is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

C:

IPv6 customers lose service even when IPv4 routing remains healthy. It is relevant if an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface, but the reported issue is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

Traffic engineering decisions depend on a route attribute outside its applicable selection scope. This could help if a network expects MED to control all outbound peer choices even when comparing routes learned from unrelated neighboring autonomous systems, but not when an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests