McAfee Secured

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

100% Juniper JN0-364 Guaranteed Success With Testking Training Materials

Get Real JN0-364 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

69 Questions & Answers with Testing Engine

"Service Provider Routing and Switching, Specialist (JNCIS-SP) Exam", also known as JN0-364 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-364 Exam Engine. Your JN0-364 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 87

Question 860

At fictional Bluehaven Backbone 215, a regional service-provider network, during a preproduction design validation, operations observes: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Which operational harm would persist without the intended correction?

  1. IPv6 service fails across a still-configured but unusable tunnel.
  2. IPv6 Internet service fails while IPv4 peering looks healthy.
  3. IPv6 customers lose service even when IPv4 routing remains healthy.
  4. Traffic engineering decisions depend on a route attribute outside its applicable selection scope.

Explanation

Correct Answer

A:

IPv6 service fails across a still-configured but unusable tunnel. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes.

Incorrect Answers

B:

IPv6 Internet service fails while IPv4 peering looks healthy. This is applicable when an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter; the present condition is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

C:

IPv6 customers lose service even when IPv4 routing remains healthy. It is relevant if an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface, but the reported issue is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

Traffic engineering decisions depend on a route attribute outside its applicable selection scope. This could help if a network expects MED to control all outbound peer choices even when comparing routes learned from unrelated neighboring autonomous systems, but not when an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Question 861

In a separate fictional JNCIS-SP lab review for Lakewood Carrier 216, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. What should the Junos specialist change first to resolve this specific fault?

  1. Create the appropriate IPv6 address-family policy matching the approved prefixes.
  2. Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables.
  3. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes.
  4. Set compatible network type and review adjacency expectations on both ends.

Explanation

Correct Answer

C:

Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic.

Incorrect Answers

A:

Create the appropriate IPv6 address-family policy matching the approved prefixes. This could matter when a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. In this case, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

B:

Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables. That could help when an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface; here, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

Set compatible network type and review adjacency expectations on both ends. It is relevant if OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology, but the reported issue is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Question 862

In a separate fictional JNCIS-SP lab review for Lakewood Carrier 216, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. What technical principle underlies the right remedy?

  1. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic.
  2. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability.
  3. BGP multiprotocol families and matching policy control IPv6 route exchange.
  4. LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths.

Explanation

Correct Answer

A:

IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes.

Incorrect Answers

B:

IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. This could matter when a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. In this case, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

C:

BGP multiprotocol families and matching policy control IPv6 route exchange. That could help when an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter; here, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. This is applicable when a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change; the present condition is that an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Question 863

In a separate fictional JNCIS-SP lab review for Lakewood Carrier 216, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Which acceptance finding demonstrates the affected service has recovered?

  1. Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end.
  2. The inet6 route is active and a controlled IPv6 probe reaches the prefix.
  3. Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed.
  4. The expected LSA is present with appropriate advertising router and area context.

Explanation

Correct Answer

C:

Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic.

Incorrect Answers

A:

Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end. That option concerns a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. The problem here is different: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

B:

The inet6 route is active and a controlled IPv6 probe reaches the prefix. It addresses a different problem: An IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. Here, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

The expected LSA is present with appropriate advertising router and area context. That could help when operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements; here, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Question 864

In a separate fictional JNCIS-SP lab review for Lakewood Carrier 216, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. What is the direct residual network risk if the fault remains unresolved?

  1. IPv6 traffic is entirely lost due to an unsuitable policy match.
  2. IPv6 service fails across a still-configured but unusable tunnel.
  3. IPv6 customers lose service even when IPv4 routing remains healthy.
  4. A premium customer service traverses a congested or disallowed link.

Explanation

Correct Answer

B:

IPv6 service fails across a still-configured but unusable tunnel. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic.

Incorrect Answers

A:

IPv6 traffic is entirely lost due to an unsuitable policy match. The choice would be appropriate if a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. Here, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

C:

IPv6 customers lose service even when IPv4 routing remains healthy. It addresses a different problem: An IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. Here, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

D:

A premium customer service traverses a congested or disallowed link. This could matter when an RSVP-signaled LSP follows a congested transit hop instead of the approved engineered route. In this case, an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared.

Question 865

At fictional Summitfield Carrier 217, a regional service-provider network, during a core-routing acceptance test, operations observes: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. Which targeted remediation best fits the reported behavior?

  1. Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes.
  2. Associate the link-local next hop with the correct egress interface and validate neighbor resolution.
  3. Check the appropriate inet6 routing instance and forwarding state.
  4. Correct the SID assignment and confirm the intended segment path resolves to that node.

Explanation

Correct Answer

C:

Check the appropriate inet6 routing instance and forwarding state. IPv4 and IPv6 route lookups use separate address-family tables. The expected IPv6 route and active forwarding next hop are visible in inet6 output.

Incorrect Answers

A:

Enable the supported IS-IS IPv6 reachability and confirm advertisements and routes. This addresses a situation in which a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation; however, a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

B:

Associate the link-local next hop with the correct egress interface and validate neighbor resolution. The choice would be appropriate if an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. Here, a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

D:

Correct the SID assignment and confirm the intended segment path resolves to that node. It addresses a different problem: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. Here, a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

Question 866

At fictional Summitfield Carrier 217, a regional service-provider network, during a core-routing acceptance test, operations observes: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. Why is this particular correction the best fit for the stated defect?

  1. Routing filters must match the relevant address family and intended prefix semantics.
  2. IPv4 and IPv6 route lookups use separate address-family tables.
  3. IPv6 forwarding requires a usable route and resolvable next hop in the correct address family.
  4. Bridge-table observations must be interpreted alongside actual physical and logical port membership.

Explanation

Correct Answer

B:

IPv4 and IPv6 route lookups use separate address-family tables. Check the appropriate inet6 routing instance and forwarding state. The expected IPv6 route and active forwarding next hop are visible in inet6 output.

Incorrect Answers

A:

Routing filters must match the relevant address family and intended prefix semantics. That relates to circumstances in which a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. Here the problem is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

C:

IPv6 forwarding requires a usable route and resolvable next hop in the correct address family. The choice would be appropriate if an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. Here, a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

D:

Bridge-table observations must be interpreted alongside actual physical and logical port membership. That option concerns a MAC is learned on an unexpected aggregation interface following a customer circuit move. The problem here is different: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

Question 867

At fictional Summitfield Carrier 217, a regional service-provider network, during a core-routing acceptance test, operations observes: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. What direct observation would prove the corrective action worked?

  1. The authorized IPv6 prefixes arrive in the intended inet6 table without IPv4 policy changes.
  2. The authorized inet6 routes are accepted while prohibited IPv6 prefixes remain blocked.
  3. The expected IPv6 route and active forwarding next hop are visible in inet6 output.
  4. Tagged customer frames enter the intended VLAN while disallowed tags are rejected.

Explanation

Correct Answer

C:

The expected IPv6 route and active forwarding next hop are visible in inet6 output. IPv4 and IPv6 route lookups use separate address-family tables. Check the appropriate inet6 routing instance and forwarding state.

Incorrect Answers

A:

The authorized IPv6 prefixes arrive in the intended inet6 table without IPv4 policy changes. It is useful for situations where an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter; the reported fault, though, is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

B:

The authorized inet6 routes are accepted while prohibited IPv6 prefixes remain blocked. That relates to circumstances in which a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. Here the problem is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

D:

Tagged customer frames enter the intended VLAN while disallowed tags are rejected. The choice would be appropriate if a provider access port drops customer tagged frames because it was configured for untagged access mode. Here, a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

Question 868

At fictional Summitfield Carrier 217, a regional service-provider network, during a core-routing acceptance test, operations observes: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. Which failure consequence follows most closely from ignoring this issue?

  1. IPv6 traffic is entirely lost due to an unsuitable policy match.
  2. IPv6 customers lose service even when IPv4 routing remains healthy.
  3. Outbound traffic takes an expensive or congested transit link.
  4. A false no-route diagnosis delays the actual IPv6 repair.

Explanation

Correct Answer

D:

A false no-route diagnosis delays the actual IPv6 repair. IPv4 and IPv6 route lookups use separate address-family tables. Check the appropriate inet6 routing instance and forwarding state.

Incorrect Answers

A:

IPv6 traffic is entirely lost due to an unsuitable policy match. This relates to a case where a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish; the current situation is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

B:

IPv6 customers lose service even when IPv4 routing remains healthy. It is useful for situations where an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface; the reported fault, though, is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

C:

Outbound traffic takes an expensive or congested transit link. That relates to circumstances in which a customer AS should prefer a primary exit but its IBGP paths have the same local preference after a policy reset. Here the problem is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

Question 869

In a separate fictional JNCIS-SP lab review for Brightstone Backbone 218, a carrier-edge and core routing team, following a monitored network change window, engineers find: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. What intervention most directly restores the intended routing or switching behavior?

  1. Correct the IPv6 family and import policy scope, then check received and advertised inet6 routes.
  2. Check the appropriate inet6 routing instance and forwarding state.
  3. Associate the link-local next hop with the correct egress interface and validate neighbor resolution.
  4. Use an appropriate segment list or routing design matching the required steering behavior.

Explanation

Correct Answer

B:

Check the appropriate inet6 routing instance and forwarding state. The expected IPv6 route and active forwarding next hop are visible in inet6 output. IPv4 and IPv6 route lookups use separate address-family tables.

Incorrect Answers

A:

Correct the IPv6 family and import policy scope, then check received and advertised inet6 routes. This could help if an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter, but not when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

C:

Associate the link-local next hop with the correct egress interface and validate neighbor resolution. It is useful for situations where an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; the reported fault, though, is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

D:

Use an appropriate segment list or routing design matching the required steering behavior. That relates to circumstances in which a team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path. Here the problem is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

Question 870

In a separate fictional JNCIS-SP lab review for Brightstone Backbone 218, a carrier-edge and core routing team, following a monitored network change window, engineers find: A support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. Which networking principle explains why the proposed correction is appropriate?

  1. IPv4 and IPv6 route lookups use separate address-family tables.
  2. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context.
  3. IS-IS can advertise enabled IPv6 information independently of IPv4 reachability.
  4. A prefix SID normally expresses reachability to a node or prefix along the underlying shortest path.

Explanation

Correct Answer

A:

IPv4 and IPv6 route lookups use separate address-family tables. The expected IPv6 route and active forwarding next hop are visible in inet6 output. Check the appropriate inet6 routing instance and forwarding state.

Incorrect Answers

B:

Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. This could help if an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design, but not when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

C:

IS-IS can advertise enabled IPv6 information independently of IPv4 reachability. This relates to a case where a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation; the current situation is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

D:

A prefix SID normally expresses reachability to a node or prefix along the underlying shortest path. It is useful for situations where a team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path; the reported fault, though, is that a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests