McAfee Secured

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

100% Juniper JN0-364 Guaranteed Success With Testking Training Materials

Get Real JN0-364 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

69 Questions & Answers with Testing Engine

"Service Provider Routing and Switching, Specialist (JNCIS-SP) Exam", also known as JN0-364 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-364 Exam Engine. Your JN0-364 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 84

Question 830

In a separate fictional JNCIS-SP lab review for Harborview ISP 208, a carrier-edge and core routing team, following a monitored network change window, engineers find: An IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. What technical principle underlies the right remedy?

  1. IPv4 and IPv6 route lookups use separate address-family tables.
  2. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context.
  3. Routing policy terms should match only their explicitly intended routes before altering route attributes.
  4. IPv6 forwarding requires a usable route and resolvable next hop in the correct address family.

Explanation

Correct Answer

D:

IPv6 forwarding requires a usable route and resolvable next hop in the correct address family. The inet6 route is active and a controlled IPv6 probe reaches the prefix. Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables.

Incorrect Answers

A:

IPv4 and IPv6 route lookups use separate address-family tables. That relates to circumstances in which a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. Here the problem is that an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

B:

Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. This addresses a situation in which an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; however, an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

C:

Routing policy terms should match only their explicitly intended routes before altering route attributes. The choice would be appropriate if a broad routing policy term changes preference for all imported prefixes instead of only the intended test network. Here, an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

Question 831

In a separate fictional JNCIS-SP lab review for Harborview ISP 208, a carrier-edge and core routing team, following a monitored network change window, engineers find: An IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. Which acceptance finding demonstrates the affected service has recovered?

  1. The inet6 route is active and a controlled IPv6 probe reaches the prefix.
  2. Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end.
  3. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix.
  4. A correctly sized customer frame traverses the entire provider handoff without drops.

Explanation

Correct Answer

A:

The inet6 route is active and a controlled IPv6 probe reaches the prefix. Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables. IPv6 forwarding requires a usable route and resolvable next hop in the correct address family.

Incorrect Answers

B:

Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end. That relates to circumstances in which a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. Here the problem is that an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

C:

OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. This addresses a situation in which an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted; however, an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

D:

A correctly sized customer frame traverses the entire provider handoff without drops. The choice would be appropriate if a service-provider QinQ link carries small frames but drops customer frames when the extra VLAN header exceeds the link MTU. Here, an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

Question 832

In a separate fictional JNCIS-SP lab review for Harborview ISP 208, a carrier-edge and core routing team, following a monitored network change window, engineers find: An IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. What is the direct residual network risk if the fault remains unresolved?

  1. A false no-route diagnosis delays the actual IPv6 repair.
  2. IPv6 customers lose service even when IPv4 routing remains healthy.
  3. IPv6 Internet service fails while IPv4 peering looks healthy.
  4. Unauthorized OSPF adjacency could expose route-control information to customer equipment.

Explanation

Correct Answer

B:

IPv6 customers lose service even when IPv4 routing remains healthy. Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables. IPv6 forwarding requires a usable route and resolvable next hop in the correct address family.

Incorrect Answers

A:

A false no-route diagnosis delays the actual IPv6 repair. This relates to a case where a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised; the current situation is that an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

C:

IPv6 Internet service fails while IPv4 peering looks healthy. That relates to circumstances in which an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter. Here the problem is that an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

D:

Unauthorized OSPF adjacency could expose route-control information to customer equipment. This addresses a situation in which a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only; however, an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface.

Question 833

At fictional Greenbridge ISP 209, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Which targeted remediation best fits the reported behavior?

  1. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes.
  2. Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables.
  3. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state.
  4. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups.

Explanation

Correct Answer

C:

Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. OSPFv3 carries IPv6 routing information and requires the relevant protocol context. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix.

Incorrect Answers

A:

Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. This could help if an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared, but not when an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

B:

Correct IPv6 next-hop reachability and inspect the inet6 routing and forwarding tables. This relates to a case where an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface; the current situation is that an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

D:

Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. That relates to circumstances in which customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. Here the problem is that an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

Question 834

At fictional Greenbridge ISP 209, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Why is this particular correction the best fit for the stated defect?

  1. OSPFv3 carries IPv6 routing information and requires the relevant protocol context.
  2. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context.
  3. Routing filters must match the relevant address family and intended prefix semantics.
  4. A discard route can protect against loops for unallocated portions of an aggregate but must not mask actual reachability.

Explanation

Correct Answer

A:

OSPFv3 carries IPv6 routing information and requires the relevant protocol context. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix.

Incorrect Answers

B:

Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. This could help if an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design, but not when an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

C:

Routing filters must match the relevant address family and intended prefix semantics. This relates to a case where a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish; the current situation is that an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

D:

A discard route can protect against loops for unallocated portions of an aggregate but must not mask actual reachability. It is useful for situations where a provider adds a discard summary but accidentally makes it cover reachable customer addresses more specific routes have not yet advertised; the reported fault, though, is that an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

Question 835

At fictional Greenbridge ISP 209, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. What direct observation would prove the corrective action worked?

  1. Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end.
  2. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix.
  3. The inet6 route is active and a controlled IPv6 probe reaches the prefix.
  4. LSP signaling succeeds with compatible reservation values and reported resource state.

Explanation

Correct Answer

B:

OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. OSPFv3 carries IPv6 routing information and requires the relevant protocol context. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state.

Incorrect Answers

A:

Remote routers learn intended IPv6 prefixes and forward IPv6 probes end to end. This is applicable when a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation; the present condition is that an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

C:

The inet6 route is active and a controlled IPv6 probe reaches the prefix. This could help if an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface, but not when an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

D:

LSP signaling succeeds with compatible reservation values and reported resource state. This relates to a case where an RSVP LSP setup fails after requested bandwidth exceeds available reservable capacity on a transit link; the current situation is that an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

Question 836

At fictional Greenbridge ISP 209, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Which failure consequence follows most closely from ignoring this issue?

  1. IPv6 traffic is entirely lost due to an unsuitable policy match.
  2. IPv6 customers lose service even when IPv4 routing remains healthy.
  3. IPv6 routing does not converge across the link.
  4. Intermittent route loss causes repeated customer outages.

Explanation

Correct Answer

C:

IPv6 routing does not converge across the link. OSPFv3 carries IPv6 routing information and requires the relevant protocol context. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state.

Incorrect Answers

A:

IPv6 traffic is entirely lost due to an unsuitable policy match. That could help when a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish; here, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

B:

IPv6 customers lose service even when IPv4 routing remains healthy. This is applicable when an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface; the present condition is that an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

D:

Intermittent route loss causes repeated customer outages. This could help if an upstream prefix repeatedly withdraws and returns but the operations view shows only the current best route, but not when an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

Question 837

In a separate fictional JNCIS-SP lab review for Fairhaven Broadband 210, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. What intervention most directly restores the intended routing or switching behavior?

  1. Create the appropriate IPv6 address-family policy matching the approved prefixes.
  2. Associate the link-local next hop with the correct egress interface and validate neighbor resolution.
  3. Adopt the supported rapid spanning-tree configuration consistently and validate role transitions.
  4. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state.

Explanation

Correct Answer

D:

Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. OSPFv3 carries IPv6 routing information and requires the relevant protocol context.

Incorrect Answers

A:

Create the appropriate IPv6 address-family policy matching the approved prefixes. This could matter when a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. In this case, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

B:

Associate the link-local next hop with the correct egress interface and validate neighbor resolution. That could help when an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; here, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

C:

Adopt the supported rapid spanning-tree configuration consistently and validate role transitions. This is applicable when a redundant access network takes far too long to recover from a link failure because it uses inappropriate legacy STP behavior; the present condition is that an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

Question 838

In a separate fictional JNCIS-SP lab review for Fairhaven Broadband 210, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Which networking principle explains why the proposed correction is appropriate?

  1. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context.
  2. Routing filters must match the relevant address family and intended prefix semantics.
  3. A passive interface can advertise connected reachability without sending OSPF hellos to customers.
  4. OSPFv3 carries IPv6 routing information and requires the relevant protocol context.

Explanation

Correct Answer

D:

OSPFv3 carries IPv6 routing information and requires the relevant protocol context. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state.

Incorrect Answers

A:

Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. It addresses a different problem: An IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design. Here, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

B:

Routing filters must match the relevant address family and intended prefix semantics. This could matter when a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. In this case, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

C:

A passive interface can advertise connected reachability without sending OSPF hellos to customers. That could help when a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only; here, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

Question 839

In a separate fictional JNCIS-SP lab review for Fairhaven Broadband 210, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Which validation result would confirm the design is now functioning?

  1. The expected IPv6 route and active forwarding next hop are visible in inet6 output.
  2. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix.
  3. The authorized inet6 routes are accepted while prohibited IPv6 prefixes remain blocked.
  4. The tenant VLAN reaches only its intended IRB gateway and routing-instance routes.

Explanation

Correct Answer

B:

OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. OSPFv3 carries IPv6 routing information and requires the relevant protocol context.

Incorrect Answers

A:

The expected IPv6 route and active forwarding next hop are visible in inet6 output. That option concerns a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised. The problem here is different: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

C:

The authorized inet6 routes are accepted while prohibited IPv6 prefixes remain blocked. This could matter when a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. In this case, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

D:

The tenant VLAN reaches only its intended IRB gateway and routing-instance routes. That could help when an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch; here, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

Question 840

In a separate fictional JNCIS-SP lab review for Fairhaven Broadband 210, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. What likely service impact does this condition create?

  1. IPv6 service fails across a still-configured but unusable tunnel.
  2. Dual-stack service is only partially operational.
  3. IPv6 routing does not converge across the link.
  4. Traffic traverses unsuitable links and topology changes become disruptive.

Explanation

Correct Answer

C:

IPv6 routing does not converge across the link. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. OSPFv3 carries IPv6 routing information and requires the relevant protocol context.

Incorrect Answers

A:

IPv6 service fails across a still-configured but unusable tunnel. The choice would be appropriate if an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Here, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

B:

Dual-stack service is only partially operational. That option concerns a core network runs IS-IS for IPv4 but has no IPv6 service reachability after dual-stack activation. The problem here is different: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

D:

Traffic traverses unsuitable links and topology changes become disruptive. This could matter when a low-capacity access switch becomes STP root after a new bridge priority setting. In this case, an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests