Question 220At fictional Seabrook Metro 055, a regional service-provider network, during a preproduction design validation, operations observes: An OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. Which operational harm would persist without the intended correction? Customer latency increases and redundant links are used inefficiently. Sites in different areas cannot exchange business traffic reliably. Outbound traffic takes an expensive or congested transit link. Expired topology data causes periodic loss of service routes. ExplanationCorrect Answer D:Expired topology data causes periodic loss of service routes. OSPF topological information must be refreshed and synchronized to remain valid. Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. Incorrect Answers A:Customer latency increases and redundant links are used inefficiently. This relates to a case where provider traffic takes a long backup path because OSPF interface costs were changed inconsistently; the current situation is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. B:Sites in different areas cannot exchange business traffic reliably. It is useful for situations where a site advertises internal prefixes inside one area, but a remote OSPF area cannot learn them because the area border configuration is incomplete; the reported fault, though, is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. C:Outbound traffic takes an expensive or congested transit link. That relates to circumstances in which a customer AS should prefer a primary exit but its IBGP paths have the same local preference after a policy reset. Here the problem is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets.
Question 221In a separate fictional JNCIS-SP lab review for Northpoint Access 056, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. What should the Junos specialist change first to resolve this specific fault? Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. Set deliberate interface priorities and confirm the DR and BDR roles after a controlled election. Check relevant LSA types and area scope before changing forwarding routes. Validate outer path, encapsulation counters, inner routing, and decapsulation at both ends. ExplanationCorrect Answer A:Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. Relevant LSAs are refreshed consistently and the route remains active across the observation period. OSPF topological information must be refreshed and synchronized to remain valid. Incorrect Answers B:Set deliberate interface priorities and confirm the DR and BDR roles after a controlled election. This relates to a case where an unplanned access router becomes designated router after its interface receives an unexpectedly high priority; the current situation is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. C:Check relevant LSA types and area scope before changing forwarding routes. It is useful for situations where operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements; the reported fault, though, is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. D:Validate outer path, encapsulation counters, inner routing, and decapsulation at both ends. That relates to circumstances in which monitoring declares a GRE circuit healthy based on logical-interface status while no encapsulated user packets are delivered. Here the problem is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets.
Question 222In a separate fictional JNCIS-SP lab review for Northpoint Access 056, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. What technical principle underlies the right remedy? OSPF interface network type influences neighbor discovery and DR behavior. OSPF neighbor formation requires appropriate compatible adjacency parameters. RSVP-TE can establish signaled LSPs subject to configured path constraints. OSPF topological information must be refreshed and synchronized to remain valid. ExplanationCorrect Answer D:OSPF topological information must be refreshed and synchronized to remain valid. Relevant LSAs are refreshed consistently and the route remains active across the observation period. Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. Incorrect Answers A:OSPF interface network type influences neighbor discovery and DR behavior. It is relevant if OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology, but the reported issue is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. B:OSPF neighbor formation requires appropriate compatible adjacency parameters. This could help if OSPF neighbors remain down after one endpoint inherits a different hello and dead timer template, but not when an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. C:RSVP-TE can establish signaled LSPs subject to configured path constraints. This relates to a case where an RSVP-signaled LSP follows a congested transit hop instead of the approved engineered route; the current situation is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets.
Question 223In a separate fictional JNCIS-SP lab review for Northpoint Access 056, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. Which acceptance finding demonstrates the affected service has recovered? Relevant LSAs are refreshed consistently and the route remains active across the observation period. Operational output identifies the intended DR and BDR and database exchange stays stable. Authenticated neighbors become Full and reject intentionally incorrect credentials. Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. ExplanationCorrect Answer A:Relevant LSAs are refreshed consistently and the route remains active across the observation period. Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. OSPF topological information must be refreshed and synchronized to remain valid. Incorrect Answers B:Operational output identifies the intended DR and BDR and database exchange stays stable. It is relevant if an unplanned access router becomes designated router after its interface receives an unexpectedly high priority, but the reported issue is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. C:Authenticated neighbors become Full and reject intentionally incorrect credentials. This could help if a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree, but not when an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. D:Both endpoint IPv4 routes and encapsulated IPv6 packet tests succeed. This relates to a case where an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared; the current situation is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets.
Question 224In a separate fictional JNCIS-SP lab review for Northpoint Access 056, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. What is the direct residual network risk if the fault remains unresolved? Unauthorized OSPF adjacency could expose route-control information to customer equipment. Remote sites lose the service route or excessive routes leak into the IGP. Packets to the customer prefix are dropped despite the static route statement being present. Expired topology data causes periodic loss of service routes. ExplanationCorrect Answer D:Expired topology data causes periodic loss of service routes. Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. OSPF topological information must be refreshed and synchronized to remain valid. Incorrect Answers A:Unauthorized OSPF adjacency could expose route-control information to customer equipment. That could help when a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only; here, an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. B:Remote sites lose the service route or excessive routes leak into the IGP. This is applicable when a static service prefix is missing from OSPF because the export policy was attached but does not match it; the present condition is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. C:Packets to the customer prefix are dropped despite the static route statement being present. It is relevant if a provider edge has a static route for a customer prefix, but its next hop resolves only through a disconnected interface, but the reported issue is that an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets.
Question 225At fictional Linden Point 057, a regional service-provider network, during a core-routing acceptance test, operations observes: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. Which targeted remediation best fits the reported behavior? Inspect database-exchange state and repair the adjacency rather than editing unrelated route preferences. Verify active next-hop resolution and transit forwarding after OSPF convergence. Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. Add an explicit approved community match and verify the intended import or export action. ExplanationCorrect Answer C:Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. OSPF peers must satisfy the configured authentication requirements to participate. Authenticated neighbors become Full and reject intentionally incorrect credentials. Incorrect Answers A:Inspect database-exchange state and repair the adjacency rather than editing unrelated route preferences. This could matter when two supposed adjacent routers have different views of a backbone link because database synchronization never completes. In this case, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. B:Verify active next-hop resolution and transit forwarding after OSPF convergence. That could help when an engineer sees an OSPF route in the routing table and closes the incident without testing the egress path; here, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. D:Add an explicit approved community match and verify the intended import or export action. It is relevant if an upstream advertises a community tag to influence treatment but an import policy ignores the agreed meaning, but the reported issue is that a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree.
Question 226At fictional Linden Point 057, a regional service-provider network, during a core-routing acceptance test, operations observes: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. Why is this particular correction the best fit for the stated defect? OSPF neighbors need compatible area context to exchange database information. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. Routing policy terms should match only their explicitly intended routes before altering route attributes. OSPF peers must satisfy the configured authentication requirements to participate. ExplanationCorrect Answer D:OSPF peers must satisfy the configured authentication requirements to participate. Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. Authenticated neighbors become Full and reject intentionally incorrect credentials. Incorrect Answers A:OSPF neighbors need compatible area context to exchange database information. It addresses a different problem: Two provider routers on a point-to-point circuit cannot form an OSPF adjacency because their interfaces use different area IDs. Here, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. B:On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. This could matter when on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure. In this case, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. C:Routing policy terms should match only their explicitly intended routes before altering route attributes. That could help when a broad routing policy term changes preference for all imported prefixes instead of only the intended test network; here, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree.
Question 227At fictional Linden Point 057, a regional service-provider network, during a core-routing acceptance test, operations observes: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. What direct observation would prove the corrective action worked? Relevant LSAs are refreshed consistently and the route remains active across the observation period. Remote routers receive the intended interarea route and retain correct area separation. Authenticated neighbors become Full and reject intentionally incorrect credentials. The penultimate and egress forwarding entries match the intended label disposition. ExplanationCorrect Answer C:Authenticated neighbors become Full and reject intentionally incorrect credentials. OSPF peers must satisfy the configured authentication requirements to participate. Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. Incorrect Answers A:Relevant LSAs are refreshed consistently and the route remains active across the observation period. That option concerns an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. The problem here is different: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. B:Remote routers receive the intended interarea route and retain correct area separation. It addresses a different problem: A site advertises internal prefixes inside one area, but a remote OSPF area cannot learn them because the area border configuration is incomplete. Here, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. D:The penultimate and egress forwarding entries match the intended label disposition. That could help when an operator sees the transport label removed near the egress and flags a failure despite the design allowing PHP; here, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree.
Question 228At fictional Linden Point 057, a regional service-provider network, during a core-routing acceptance test, operations observes: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. Which failure consequence follows most closely from ignoring this issue? The adjacency repeatedly fails and transit traffic loses a redundant path. Misdiagnosis delays restoration because absent control-plane information is overlooked. Routing connectivity fails or a poorly scoped workaround weakens control-plane trust. Unwanted routes may alter forwarding or create customer traffic leakage. ExplanationCorrect Answer C:Routing connectivity fails or a poorly scoped workaround weakens control-plane trust. OSPF peers must satisfy the configured authentication requirements to participate. Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. Incorrect Answers A:The adjacency repeatedly fails and transit traffic loses a redundant path. The choice would be appropriate if OSPF neighbors remain down after one endpoint inherits a different hello and dead timer template. Here, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. B:Misdiagnosis delays restoration because absent control-plane information is overlooked. That option concerns operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. The problem here is different: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. D:Unwanted routes may alter forwarding or create customer traffic leakage. This could matter when a provider receives a customer-only prefix from a transit peer that should be blocked by an import policy. In this case, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree.
Question 229In a separate fictional JNCIS-SP lab review for Harborview ISP 058, a carrier-edge and core routing team, following a monitored network change window, engineers find: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. What intervention most directly restores the intended routing or switching behavior? Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. Restrict the discard summary and verify that intended specific routes win for live destinations. ExplanationCorrect Answer B:Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. Authenticated neighbors become Full and reject intentionally incorrect credentials. OSPF peers must satisfy the configured authentication requirements to participate. Incorrect Answers A:Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. This addresses a situation in which an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets; however, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. C:Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. That option concerns a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. The problem here is different: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. D:Restrict the discard summary and verify that intended specific routes win for live destinations. It addresses a different problem: A provider adds a discard summary but accidentally makes it cover reachable customer addresses more specific routes have not yet advertised. Here, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree.
Question 230In a separate fictional JNCIS-SP lab review for Harborview ISP 058, a carrier-edge and core routing team, following a monitored network change window, engineers find: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. Which networking principle explains why the proposed correction is appropriate? OSPF route visibility depends on appropriate LSA origination and flooding through the area topology. OSPF topological information must be refreshed and synchronized to remain valid. Filter-based forwarding selects a routing lookup context based on packet classification. OSPF peers must satisfy the configured authentication requirements to participate. ExplanationCorrect Answer D:OSPF peers must satisfy the configured authentication requirements to participate. Authenticated neighbors become Full and reject intentionally incorrect credentials. Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. Incorrect Answers A:OSPF route visibility depends on appropriate LSA origination and flooding through the area topology. That relates to circumstances in which operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. Here the problem is that a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. B:OSPF topological information must be refreshed and synchronized to remain valid. This addresses a situation in which an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets; however, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. C:Filter-based forwarding selects a routing lookup context based on packet classification. The choice would be appropriate if a traffic class should be steered into an alternate routing instance but the firewall filter maps it to the default route lookup. Here, a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree.