Question 200In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 050, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. What likely service impact does this condition create? Customers still experience blackholes despite apparently healthy protocol neighbors. Expired topology data causes periodic loss of service routes. Invalid or unintended address space can enter forwarding decisions and misdirect traffic. Customer latency increases and redundant links are used inefficiently. ExplanationCorrect Answer D:Customer latency increases and redundant links are used inefficiently. Review planned OSPF costs in both directions and correct the traffic-engineering values. OSPF SPF computes least-cost paths using the advertised topology metrics. Incorrect Answers A:Customers still experience blackholes despite apparently healthy protocol neighbors. That could help when an engineer sees an OSPF route in the routing table and closes the incident without testing the egress path; here, provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. B:Expired topology data causes periodic loss of service routes. This is applicable when an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets; the present condition is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. C:Invalid or unintended address space can enter forwarding decisions and misdirect traffic. It is relevant if a router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing, but the reported issue is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.
Question 201At fictional Hillside Transit 051, a regional service-provider network, during a planned PE-to-core handoff, operations observes: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. Which configuration or operational correction most directly addresses this failure? Assign unique stable router IDs and safely reestablish affected OSPF adjacencies. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. Fix the OSPF export policy's precise match and validate external route origination. Investigate Layer 2 topology, bridge membership and possible loop before route-policy changes. ExplanationCorrect Answer B:Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. A passive interface can advertise connected reachability without sending OSPF hellos to customers. Customer subnet is visible in the IGP but no neighbor session forms on the LAN. Incorrect Answers A:Assign unique stable router IDs and safely reestablish affected OSPF adjacencies. This could matter when two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. In this case, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. C:Fix the OSPF export policy's precise match and validate external route origination. This is applicable when a static service prefix is missing from OSPF because the export policy was attached but does not match it; the present condition is that a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. D:Investigate Layer 2 topology, bridge membership and possible loop before route-policy changes. It is relevant if a MAC moves rapidly among provider ports after a cabling change, yet troubleshooting focuses only on IP routing tables, but the reported issue is that a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only.
Question 202At fictional Hillside Transit 051, a regional service-provider network, during a planned PE-to-core handoff, operations observes: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. Which Junos forwarding or control-plane rule applies to this case? The OSPF router ID uniquely identifies a router in link-state advertisements. OSPF shortest-path calculations rely on consistent synchronized link-state information within an area. A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. A passive interface can advertise connected reachability without sending OSPF hellos to customers. ExplanationCorrect Answer D:A passive interface can advertise connected reachability without sending OSPF hellos to customers. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. Customer subnet is visible in the IGP but no neighbor session forms on the LAN. Incorrect Answers A:The OSPF router ID uniquely identifies a router in link-state advertisements. It addresses a different problem: Two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. Here, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. B:OSPF shortest-path calculations rely on consistent synchronized link-state information within an area. This could matter when two supposed adjacent routers have different views of a backbone link because database synchronization never completes. In this case, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. C:A healthy IS-IS adjacency does not prove the intended shortest path is active in the forwarding plane. That could help when the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change; here, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only.
Question 203At fictional Hillside Transit 051, a regional service-provider network, during a planned PE-to-core handoff, operations observes: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. What operational evidence best establishes successful remediation? Customer subnet is visible in the IGP but no neighbor session forms on the LAN. Operational output identifies the intended DR and BDR and database exchange stays stable. Neighbor state stabilizes and hello and dead intervals match on both endpoints. Peers retain valid routes during a tested restart and withdraw stale state after the appropriate interval. ExplanationCorrect Answer A:Customer subnet is visible in the IGP but no neighbor session forms on the LAN. A passive interface can advertise connected reachability without sending OSPF hellos to customers. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. Incorrect Answers B:Operational output identifies the intended DR and BDR and database exchange stays stable. It addresses a different problem: An unplanned access router becomes designated router after its interface receives an unexpectedly high priority. Here, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. C:Neighbor state stabilizes and hello and dead intervals match on both endpoints. This could matter when OSPF neighbors remain down after one endpoint inherits a different hello and dead timer template. In this case, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. D:Peers retain valid routes during a tested restart and withdraw stale state after the appropriate interval. That could help when a provider assumes graceful restart will work during a routing process restart without considering neighbor support; here, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only.
Question 204At fictional Hillside Transit 051, a regional service-provider network, during a planned PE-to-core handoff, operations observes: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. Which operational harm would persist without the intended correction? Customer latency increases and redundant links are used inefficiently. Routing connectivity fails or a poorly scoped workaround weakens control-plane trust. MPLS traffic cannot use the planned engineered transport path. Unauthorized OSPF adjacency could expose route-control information to customer equipment. ExplanationCorrect Answer D:Unauthorized OSPF adjacency could expose route-control information to customer equipment. A passive interface can advertise connected reachability without sending OSPF hellos to customers. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. Incorrect Answers A:Customer latency increases and redundant links are used inefficiently. The choice would be appropriate if provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. Here, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. B:Routing connectivity fails or a poorly scoped workaround weakens control-plane trust. That option concerns a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. The problem here is different: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. C:MPLS traffic cannot use the planned engineered transport path. It addresses a different problem: An RSVP LSP stays down but engineers only examine the ingress router's IP default route. Here, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only.
Question 205In a separate fictional JNCIS-SP lab review for Westbridge Exchange 052, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. What should the Junos specialist change first to resolve this specific fault? Inspect database-exchange state and repair the adjacency rather than editing unrelated route preferences. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. Fix the OSPF export policy's precise match and validate external route origination. Confirm the configured graceful-restart and helper capabilities on participating peers before testing recovery. ExplanationCorrect Answer B:Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. Customer subnet is visible in the IGP but no neighbor session forms on the LAN. A passive interface can advertise connected reachability without sending OSPF hellos to customers. Incorrect Answers A:Inspect database-exchange state and repair the adjacency rather than editing unrelated route preferences. This addresses a situation in which two supposed adjacent routers have different views of a backbone link because database synchronization never completes; however, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. C:Fix the OSPF export policy's precise match and validate external route origination. That option concerns a static service prefix is missing from OSPF because the export policy was attached but does not match it. The problem here is different: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. D:Confirm the configured graceful-restart and helper capabilities on participating peers before testing recovery. It addresses a different problem: A provider assumes graceful restart will work during a routing process restart without considering neighbor support. Here, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only.
Question 206In a separate fictional JNCIS-SP lab review for Westbridge Exchange 052, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. What technical principle underlies the right remedy? OSPF peers must satisfy the configured authentication requirements to participate. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. A passive interface can advertise connected reachability without sending OSPF hellos to customers. Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. ExplanationCorrect Answer C:A passive interface can advertise connected reachability without sending OSPF hellos to customers. Customer subnet is visible in the IGP but no neighbor session forms on the LAN. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. Incorrect Answers A:OSPF peers must satisfy the configured authentication requirements to participate. That relates to circumstances in which a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. Here the problem is that a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. B:On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. This addresses a situation in which on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure; however, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. D:Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. That option concerns a provider assumes graceful restart will work during a routing process restart without considering neighbor support. The problem here is different: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only.
Question 207In a separate fictional JNCIS-SP lab review for Westbridge Exchange 052, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. Which acceptance finding demonstrates the affected service has recovered? Customer subnet is visible in the IGP but no neighbor session forms on the LAN. The expected LSA is present with appropriate advertising router and area context. Relevant LSAs are refreshed consistently and the route remains active across the observation period. The route is active and the forwarding lookup shows an operational egress next hop. ExplanationCorrect Answer A:Customer subnet is visible in the IGP but no neighbor session forms on the LAN. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. A passive interface can advertise connected reachability without sending OSPF hellos to customers. Incorrect Answers B:The expected LSA is present with appropriate advertising router and area context. That relates to circumstances in which operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. Here the problem is that a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. C:Relevant LSAs are refreshed consistently and the route remains active across the observation period. This addresses a situation in which an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets; however, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. D:The route is active and the forwarding lookup shows an operational egress next hop. The choice would be appropriate if an engineer reports recovery because a route appears in protocol output, but the hardware forwarding table still lacks a usable next hop. Here, a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only.
Question 208In a separate fictional JNCIS-SP lab review for Westbridge Exchange 052, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. What is the direct residual network risk if the fault remains unresolved? Customer latency increases and redundant links are used inefficiently. Sites in different areas cannot exchange business traffic reliably. Packets cannot travel the intended MPLS transport path. Unauthorized OSPF adjacency could expose route-control information to customer equipment. ExplanationCorrect Answer D:Unauthorized OSPF adjacency could expose route-control information to customer equipment. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. A passive interface can advertise connected reachability without sending OSPF hellos to customers. Incorrect Answers A:Customer latency increases and redundant links are used inefficiently. This relates to a case where provider traffic takes a long backup path because OSPF interface costs were changed inconsistently; the current situation is that a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. B:Sites in different areas cannot exchange business traffic reliably. It is useful for situations where a site advertises internal prefixes inside one area, but a remote OSPF area cannot learn them because the area border configuration is incomplete; the reported fault, though, is that a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. C:Packets cannot travel the intended MPLS transport path. That relates to circumstances in which an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. Here the problem is that a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only.
Question 209At fictional Crestland Networks 053, a regional service-provider network, during a two-site transit migration, operations observes: Operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. Which targeted remediation best fits the reported behavior? Make the timer settings compatible across the shared link and monitor the neighbor exchange. Check relevant LSA types and area scope before changing forwarding routes. Verify active next-hop resolution and transit forwarding after OSPF convergence. Align the peer type and AS settings with the intended same-AS design. ExplanationCorrect Answer B:Check relevant LSA types and area scope before changing forwarding routes. OSPF route visibility depends on appropriate LSA origination and flooding through the area topology. The expected LSA is present with appropriate advertising router and area context. Incorrect Answers A:Make the timer settings compatible across the shared link and monitor the neighbor exchange. This could help if OSPF neighbors remain down after one endpoint inherits a different hello and dead timer template, but not when operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. C:Verify active next-hop resolution and transit forwarding after OSPF convergence. It is useful for situations where an engineer sees an OSPF route in the routing table and closes the incident without testing the egress path; the reported fault, though, is that operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. D:Align the peer type and AS settings with the intended same-AS design. That relates to circumstances in which an operator configures an internal route-reflector session as EBGP and introduces an unintended AS boundary. Here the problem is that operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements.
Question 210At fictional Crestland Networks 053, a regional service-provider network, during a two-site transit migration, operations observes: Operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. Why is this particular correction the best fit for the stated defect? OSPF route visibility depends on appropriate LSA origination and flooding through the area topology. The OSPF router ID uniquely identifies a router in link-state advertisements. OSPF neighbors need compatible area context to exchange database information. LDP discovery and the TCP-based LDP session depend on usable transport reachability. ExplanationCorrect Answer A:OSPF route visibility depends on appropriate LSA origination and flooding through the area topology. Check relevant LSA types and area scope before changing forwarding routes. The expected LSA is present with appropriate advertising router and area context. Incorrect Answers B:The OSPF router ID uniquely identifies a router in link-state advertisements. This could help if two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template, but not when operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. C:OSPF neighbors need compatible area context to exchange database information. This relates to a case where two provider routers on a point-to-point circuit cannot form an OSPF adjacency because their interfaces use different area IDs; the current situation is that operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. D:LDP discovery and the TCP-based LDP session depend on usable transport reachability. It is useful for situations where two core routers cannot form an LDP session even though they discover one another on the connected link; the reported fault, though, is that operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements.