McAfee Secured

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

100% Juniper JN0-364 Guaranteed Success With Testking Training Materials

Get Real JN0-364 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

69 Questions & Answers with Testing Engine

"Service Provider Routing and Switching, Specialist (JNCIS-SP) Exam", also known as JN0-364 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-364 Exam Engine. Your JN0-364 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 20

Question 190

In a separate fictional JNCIS-SP lab review for Stonefield Telecom 048, a carrier-edge and core routing team, following a monitored network change window, engineers find: OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology. What technical principle underlies the right remedy?

  1. The OSPF router ID uniquely identifies a router in link-state advertisements.
  2. OSPF interface network type influences neighbor discovery and DR behavior.
  3. OSPF route visibility depends on appropriate LSA origination and flooding through the area topology.
  4. Link-local IPv6 addresses are scoped to a link and require an appropriate interface context.

Explanation

Correct Answer

B:

OSPF interface network type influences neighbor discovery and DR behavior. The circuit forms the expected point-to-point adjacency without an unwanted DR election. Set compatible network type and review adjacency expectations on both ends.

Incorrect Answers

A:

The OSPF router ID uniquely identifies a router in link-state advertisements. It addresses a different problem: Two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. Here, OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

C:

OSPF route visibility depends on appropriate LSA origination and flooding through the area topology. That could help when operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements; here, OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

D:

Link-local IPv6 addresses are scoped to a link and require an appropriate interface context. This is applicable when an IPv6 adjacency uses a link-local next hop, but its interface scope is omitted from the implementation design; the present condition is that OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

Question 191

In a separate fictional JNCIS-SP lab review for Stonefield Telecom 048, a carrier-edge and core routing team, following a monitored network change window, engineers find: OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology. Which acceptance finding demonstrates the affected service has recovered?

  1. The circuit forms the expected point-to-point adjacency without an unwanted DR election.
  2. The approved prefix is present as an external OSPF route and unauthorized prefixes remain absent.
  3. The expected LSA is present with appropriate advertising router and area context.
  4. Both client sessions stabilize and expected reflected routes reach peers.

Explanation

Correct Answer

A:

The circuit forms the expected point-to-point adjacency without an unwanted DR election. Set compatible network type and review adjacency expectations on both ends. OSPF interface network type influences neighbor discovery and DR behavior.

Incorrect Answers

B:

The approved prefix is present as an external OSPF route and unauthorized prefixes remain absent. It addresses a different problem: A static service prefix is missing from OSPF because the export policy was attached but does not match it. Here, OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

C:

The expected LSA is present with appropriate advertising router and area context. This could matter when operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. In this case, OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

D:

Both client sessions stabilize and expected reflected routes reach peers. That could help when an internal client learns routes from another client only intermittently after the route-reflector peering address changes; here, OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

Question 192

In a separate fictional JNCIS-SP lab review for Stonefield Telecom 048, a carrier-edge and core routing team, following a monitored network change window, engineers find: OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology. What is the direct residual network risk if the fault remains unresolved?

  1. Misdiagnosis delays restoration because absent control-plane information is overlooked.
  2. Routing connectivity fails or a poorly scoped workaround weakens control-plane trust.
  3. A transit route remains unavailable because neighbor behavior is inconsistent.
  4. Traffic bypasses an approved low-latency or protected path.

Explanation

Correct Answer

C:

A transit route remains unavailable because neighbor behavior is inconsistent. Set compatible network type and review adjacency expectations on both ends. OSPF interface network type influences neighbor discovery and DR behavior.

Incorrect Answers

A:

Misdiagnosis delays restoration because absent control-plane information is overlooked. The choice would be appropriate if operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements. Here, OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

B:

Routing connectivity fails or a poorly scoped workaround weakens control-plane trust. That option concerns a newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. The problem here is different: OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

D:

Traffic bypasses an approved low-latency or protected path. This could matter when a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. In this case, OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology.

Question 193

At fictional Clearwater Peering 049, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. Which targeted remediation best fits the reported behavior?

  1. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement.
  2. Review planned OSPF costs in both directions and correct the traffic-engineering values.
  3. Assign unique stable router IDs and safely reestablish affected OSPF adjacencies.
  4. Inspect spanning-tree port role, state, and received BPDU information before changing hardware.

Explanation

Correct Answer

B:

Review planned OSPF costs in both directions and correct the traffic-engineering values. OSPF SPF computes least-cost paths using the advertised topology metrics. Route detail and controlled traffic testing select the documented primary path.

Incorrect Answers

A:

Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. This addresses a situation in which a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only; however, provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

C:

Assign unique stable router IDs and safely reestablish affected OSPF adjacencies. That option concerns two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. The problem here is different: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

D:

Inspect spanning-tree port role, state, and received BPDU information before changing hardware. It addresses a different problem: A link is physically up but stays blocked by spanning tree, and an operator incorrectly blames interface optics. Here, provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

Question 194

At fictional Clearwater Peering 049, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. Why is this particular correction the best fit for the stated defect?

  1. OSPF neighbor formation requires appropriate compatible adjacency parameters.
  2. OSPF SPF computes least-cost paths using the advertised topology metrics.
  3. OSPF shortest-path calculations rely on consistent synchronized link-state information within an area.
  4. IS-IS authentication parameters must match for participating routers to exchange protocol information.

Explanation

Correct Answer

B:

OSPF SPF computes least-cost paths using the advertised topology metrics. Review planned OSPF costs in both directions and correct the traffic-engineering values. Route detail and controlled traffic testing select the documented primary path.

Incorrect Answers

A:

OSPF neighbor formation requires appropriate compatible adjacency parameters. That relates to circumstances in which OSPF neighbors remain down after one endpoint inherits a different hello and dead timer template. Here the problem is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

C:

OSPF shortest-path calculations rely on consistent synchronized link-state information within an area. The choice would be appropriate if two supposed adjacent routers have different views of a backbone link because database synchronization never completes. Here, provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

D:

IS-IS authentication parameters must match for participating routers to exchange protocol information. That option concerns a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end. The problem here is different: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

Question 195

At fictional Clearwater Peering 049, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. What direct observation would prove the corrective action worked?

  1. Route lookup and sample packets both follow the intended egress circuit after convergence.
  2. Route detail and controlled traffic testing select the documented primary path.
  3. Operational output identifies the intended DR and BDR and database exchange stays stable.
  4. The expected neighbor appears with stable hold time and correct interface state.

Explanation

Correct Answer

B:

Route detail and controlled traffic testing select the documented primary path. OSPF SPF computes least-cost paths using the advertised topology metrics. Review planned OSPF costs in both directions and correct the traffic-engineering values.

Incorrect Answers

A:

Route lookup and sample packets both follow the intended egress circuit after convergence. It is useful for situations where an engineer sees an OSPF route in the routing table and closes the incident without testing the egress path; the reported fault, though, is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

C:

Operational output identifies the intended DR and BDR and database exchange stays stable. This addresses a situation in which an unplanned access router becomes designated router after its interface receives an unexpectedly high priority; however, provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

D:

The expected neighbor appears with stable hold time and correct interface state. The choice would be appropriate if an IS-IS neighbor remains down after an interface template disables its hello transmission. Here, provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

Question 196

At fictional Clearwater Peering 049, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. Which failure consequence follows most closely from ignoring this issue?

  1. Duplicate identity produces unstable topology and confusing route calculations.
  2. Unauthorized OSPF adjacency could expose route-control information to customer equipment.
  3. Tunnel establishment loops or collapses during forwarding changes.
  4. Customer latency increases and redundant links are used inefficiently.

Explanation

Correct Answer

D:

Customer latency increases and redundant links are used inefficiently. OSPF SPF computes least-cost paths using the advertised topology metrics. Review planned OSPF costs in both directions and correct the traffic-engineering values.

Incorrect Answers

A:

Duplicate identity produces unstable topology and confusing route calculations. This relates to a case where two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template; the current situation is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

B:

Unauthorized OSPF adjacency could expose route-control information to customer equipment. It is useful for situations where a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only; the reported fault, though, is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

C:

Tunnel establishment loops or collapses during forwarding changes. That relates to circumstances in which a route to a GRE destination is learned through the same tunnel, creating recursive or looping resolution. Here the problem is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

Question 197

In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 050, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. What intervention most directly restores the intended routing or switching behavior?

  1. Fix the OSPF export policy's precise match and validate external route origination.
  2. Review planned OSPF costs in both directions and correct the traffic-engineering values.
  3. Assign unique stable router IDs and safely reestablish affected OSPF adjacencies.
  4. Restore consistent client-to-reflector peering and reachable loopback endpoints.

Explanation

Correct Answer

B:

Review planned OSPF costs in both directions and correct the traffic-engineering values. Route detail and controlled traffic testing select the documented primary path. OSPF SPF computes least-cost paths using the advertised topology metrics.

Incorrect Answers

A:

Fix the OSPF export policy's precise match and validate external route origination. This could help if a static service prefix is missing from OSPF because the export policy was attached but does not match it, but not when provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

C:

Assign unique stable router IDs and safely reestablish affected OSPF adjacencies. It is useful for situations where two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template; the reported fault, though, is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

D:

Restore consistent client-to-reflector peering and reachable loopback endpoints. That relates to circumstances in which an internal client learns routes from another client only intermittently after the route-reflector peering address changes. Here the problem is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

Question 198

In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 050, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. Which networking principle explains why the proposed correction is appropriate?

  1. OSPF route visibility depends on appropriate LSA origination and flooding through the area topology.
  2. OSPF interface network type influences neighbor discovery and DR behavior.
  3. VRRP provides a shared virtual gateway address with an active router and standby candidates.
  4. OSPF SPF computes least-cost paths using the advertised topology metrics.

Explanation

Correct Answer

D:

OSPF SPF computes least-cost paths using the advertised topology metrics. Route detail and controlled traffic testing select the documented primary path. Review planned OSPF costs in both directions and correct the traffic-engineering values.

Incorrect Answers

A:

OSPF route visibility depends on appropriate LSA origination and flooding through the area topology. It is relevant if operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements, but the reported issue is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

B:

OSPF interface network type influences neighbor discovery and DR behavior. This could help if OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology, but not when provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

C:

VRRP provides a shared virtual gateway address with an active router and standby candidates. This relates to a case where an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect; the current situation is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

Question 199

In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 050, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. Which validation result would confirm the design is now functioning?

  1. Route detail and controlled traffic testing select the documented primary path.
  2. Neighbor state stabilizes and hello and dead intervals match on both endpoints.
  3. Operational output identifies the intended DR and BDR and database exchange stays stable.
  4. Operational output identifies the intended DIS and a stable pseudonode LSP.

Explanation

Correct Answer

A:

Route detail and controlled traffic testing select the documented primary path. Review planned OSPF costs in both directions and correct the traffic-engineering values. OSPF SPF computes least-cost paths using the advertised topology metrics.

Incorrect Answers

B:

Neighbor state stabilizes and hello and dead intervals match on both endpoints. It is relevant if OSPF neighbors remain down after one endpoint inherits a different hello and dead timer template, but the reported issue is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

C:

Operational output identifies the intended DR and BDR and database exchange stays stable. This could help if an unplanned access router becomes designated router after its interface receives an unexpectedly high priority, but not when provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

D:

Operational output identifies the intended DIS and a stable pseudonode LSP. This relates to a case where operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment; the current situation is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

Question 200

In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 050, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: Provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. What likely service impact does this condition create?

  1. Customers still experience blackholes despite apparently healthy protocol neighbors.
  2. Expired topology data causes periodic loss of service routes.
  3. Invalid or unintended address space can enter forwarding decisions and misdirect traffic.
  4. Customer latency increases and redundant links are used inefficiently.

Explanation

Correct Answer

D:

Customer latency increases and redundant links are used inefficiently. Review planned OSPF costs in both directions and correct the traffic-engineering values. OSPF SPF computes least-cost paths using the advertised topology metrics.

Incorrect Answers

A:

Customers still experience blackholes despite apparently healthy protocol neighbors. That could help when an engineer sees an OSPF route in the routing table and closes the incident without testing the egress path; here, provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

B:

Expired topology data causes periodic loss of service routes. This is applicable when an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets; the present condition is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

C:

Invalid or unintended address space can enter forwarding decisions and misdirect traffic. It is relevant if a router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing, but the reported issue is that provider traffic takes a long backup path because OSPF interface costs were changed inconsistently.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests