Question 1A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. Which ONTAP administration step most directly corrects this failure? Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. Evaluate an appropriately supported ASA design for the SAN-only application and its required protocols. Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. Size an ONTAP platform using representative VDI deduplication and snapshot/clone behavior alongside worst-case capacity headroom. ExplanationCorrect Answer A:Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. Acceptance requires: Replay production-like random I/O and compare p95 latency and controller headroom with the service objective. Other Answers B:Evaluate an appropriately supported ASA design for the SAN-only application and its required protocols. This responds to another physical storage systems issue: A storage architect proposes to use a NAS-focused FAS setup for a dedicated block-only application that requires a simplified SAN operational model. Its mechanism is: A SAN-optimized platform streamlines the intended block workload but does not replace NAS services for unrelated file-sharing requirements. The present case instead requires: Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. C:Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. This responds to another physical storage systems issue: An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. Its mechanism is: Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. The present case instead requires: Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. D:Size an ONTAP platform using representative VDI deduplication and snapshot/clone behavior alongside worst-case capacity headroom. This responds to another physical storage systems issue: A virtual desktop farm expects tens of terabytes of mostly repeated OS image blocks, but procurement counts logical guest image sizes as fully unique physical storage. Its mechanism is: Identical virtual desktop blocks can share physical space through storage efficiency, so logical provisioned size is not equal to consumed physical capacity. The present case instead requires: Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware.
Question 2A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. Which technical distinction most directly explains the observed result? A SAN-optimized platform streamlines the intended block workload but does not replace NAS services for unrelated file-sharing requirements. All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. Identical virtual desktop blocks can share physical space through storage efficiency, so logical provisioned size is not equal to consumed physical capacity. ExplanationCorrect Answer B:All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. The corrective design is: Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. A relevant test is: Replay production-like random I/O and compare p95 latency and controller headroom with the service objective. Other Answers A:A SAN-optimized platform streamlines the intended block workload but does not replace NAS services for unrelated file-sharing requirements. That mechanism fits a different physical storage systems failure: A storage architect proposes to use a NAS-focused FAS setup for a dedicated block-only application that requires a simplified SAN operational model. Here the decisive mechanism is: All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. C:Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. That mechanism fits a different physical storage systems failure: An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. Here the decisive mechanism is: All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. D:Identical virtual desktop blocks can share physical space through storage efficiency, so logical provisioned size is not equal to consumed physical capacity. That mechanism fits a different physical storage systems failure: A virtual desktop farm expects tens of terabytes of mostly repeated OS image blocks, but procurement counts logical guest image sizes as fully unique physical storage. Here the decisive mechanism is: All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness.
Question 3A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. What check best verifies this change under the stated operating conditions? Verify the selected ASA model, host multipathing and supported FC or iSCSI connectivity with representative LUN I/O. Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions. Replay production-like random I/O and compare p95 latency and controller headroom with the service objective. Measure physical used, deduplication savings and write amplification under a representative VDI workload. ExplanationCorrect Answer C:Replay production-like random I/O and compare p95 latency and controller headroom with the service objective. This checks whether the remediation works: Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. The governing behavior is: All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. Other Answers A:Verify the selected ASA model, host multipathing and supported FC or iSCSI connectivity with representative LUN I/O. That check tests the separate condition: A storage architect proposes to use a NAS-focused FAS setup for a dedicated block-only application that requires a simplified SAN operational model. It would not establish the required result here: Replay production-like random I/O and compare p95 latency and controller headroom with the service objective. B:Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions. That check tests the separate condition: An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. It would not establish the required result here: Replay production-like random I/O and compare p95 latency and controller headroom with the service objective. D:Measure physical used, deduplication savings and write amplification under a representative VDI workload. That check tests the separate condition: A virtual desktop farm expects tens of terabytes of mostly repeated OS image blocks, but procurement counts logical guest image sizes as fully unique physical storage. It would not establish the required result here: Replay production-like random I/O and compare p95 latency and controller headroom with the service objective.
Question 4A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. What control should the team keep after the corrective change has passed testing? Require workload I/O profiles and supported hardware sizing evidence during storage-platform selection. Include host interoperability and protocol-role fit in platform approval tests. Maintain a versioned approved hardware configuration record for each lifecycle change. Set capacity alerts based on actual physical use and growth rather than logical allocation alone. ExplanationCorrect Answer A:Require workload I/O profiles and supported hardware sizing evidence during storage-platform selection. This addresses the recurring cause: All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. It keeps the accepted correction in place: Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. Other Answers B:Include host interoperability and protocol-role fit in platform approval tests. This safeguard targets a different repeat failure: A storage architect proposes to use a NAS-focused FAS setup for a dedicated block-only application that requires a simplified SAN operational model. For the present risk, the necessary control is: Require workload I/O profiles and supported hardware sizing evidence during storage-platform selection. C:Maintain a versioned approved hardware configuration record for each lifecycle change. This safeguard targets a different repeat failure: An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. For the present risk, the necessary control is: Require workload I/O profiles and supported hardware sizing evidence during storage-platform selection. D:Set capacity alerts based on actual physical use and growth rather than logical allocation alone. This safeguard targets a different repeat failure: A virtual desktop farm expects tens of terabytes of mostly repeated OS image blocks, but procurement counts logical guest image sizes as fully unique physical storage. For the present risk, the necessary control is: Require workload I/O profiles and supported hardware sizing evidence during storage-platform selection.
Question 5An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. Which change most directly meets the stated storage requirement? Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. Deploy a supported ONTAP HA pair with matching controller roles and verified partner takeover capacity. Size an ONTAP platform using representative VDI deduplication and snapshot/clone behavior alongside worst-case capacity headroom. ExplanationCorrect Answer A:Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. Acceptance requires: Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions. Other Answers B:Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. This responds to another physical storage systems issue: A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. Its mechanism is: All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. The present case instead requires: Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. C:Deploy a supported ONTAP HA pair with matching controller roles and verified partner takeover capacity. This responds to another physical storage systems issue: A remote site wants a two-controller deployment that keeps serving data after one controller fails without relying on an untested single-controller design. Its mechanism is: The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured. The present case instead requires: Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. D:Size an ONTAP platform using representative VDI deduplication and snapshot/clone behavior alongside worst-case capacity headroom. This responds to another physical storage systems issue: A virtual desktop farm expects tens of terabytes of mostly repeated OS image blocks, but procurement counts logical guest image sizes as fully unique physical storage. Its mechanism is: Identical virtual desktop blocks can share physical space through storage efficiency, so logical provisioned size is not equal to consumed physical capacity. The present case instead requires: Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase.
Question 6An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. Why would the proposed setup fail to provide the stated behavior? All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured. Identical virtual desktop blocks can share physical space through storage efficiency, so logical provisioned size is not equal to consumed physical capacity. ExplanationCorrect Answer B:Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. The corrective design is: Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. A relevant test is: Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions. Other Answers A:All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. That mechanism fits a different physical storage systems failure: A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. Here the decisive mechanism is: Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. C:The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured. That mechanism fits a different physical storage systems failure: A remote site wants a two-controller deployment that keeps serving data after one controller fails without relying on an untested single-controller design. Here the decisive mechanism is: Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. D:Identical virtual desktop blocks can share physical space through storage efficiency, so logical provisioned size is not equal to consumed physical capacity. That mechanism fits a different physical storage systems failure: A virtual desktop farm expects tens of terabytes of mostly repeated OS image blocks, but procurement counts logical guest image sizes as fully unique physical storage. Here the decisive mechanism is: Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone.
Question 7An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. Which result should be required before the storage change is accepted? Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions. Replay production-like random I/O and compare p95 latency and controller headroom with the service objective. Test a controlled takeover and giveback while monitoring client I/O continuity and remaining resource headroom. Measure physical used, deduplication savings and write amplification under a representative VDI workload. ExplanationCorrect Answer A:Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions. This checks whether the remediation works: Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. The governing behavior is: Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. Other Answers B:Replay production-like random I/O and compare p95 latency and controller headroom with the service objective. That check tests the separate condition: A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. It would not establish the required result here: Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions. C:Test a controlled takeover and giveback while monitoring client I/O continuity and remaining resource headroom. That check tests the separate condition: A remote site wants a two-controller deployment that keeps serving data after one controller fails without relying on an untested single-controller design. It would not establish the required result here: Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions. D:Measure physical used, deduplication savings and write amplification under a representative VDI workload. That check tests the separate condition: A virtual desktop farm expects tens of terabytes of mostly repeated OS image blocks, but procurement counts logical guest image sizes as fully unique physical storage. It would not establish the required result here: Compare the exact part numbers and ONTAP release against current supported-platform tables and record any exceptions.
Question 8An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. Which durable operational control best prevents this issue from recurring? Require workload I/O profiles and supported hardware sizing evidence during storage-platform selection. Schedule HA failover drills and verify partner capacity before workload growth. Maintain a versioned approved hardware configuration record for each lifecycle change. Set capacity alerts based on actual physical use and growth rather than logical allocation alone. ExplanationCorrect Answer C:Maintain a versioned approved hardware configuration record for each lifecycle change. This addresses the recurring cause: Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. It keeps the accepted correction in place: Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. Other Answers A:Require workload I/O profiles and supported hardware sizing evidence during storage-platform selection. This safeguard targets a different repeat failure: A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. For the present risk, the necessary control is: Maintain a versioned approved hardware configuration record for each lifecycle change. B:Schedule HA failover drills and verify partner capacity before workload growth. This safeguard targets a different repeat failure: A remote site wants a two-controller deployment that keeps serving data after one controller fails without relying on an untested single-controller design. For the present risk, the necessary control is: Maintain a versioned approved hardware configuration record for each lifecycle change. D:Set capacity alerts based on actual physical use and growth rather than logical allocation alone. This safeguard targets a different repeat failure: A virtual desktop farm expects tens of terabytes of mostly repeated OS image blocks, but procurement counts logical guest image sizes as fully unique physical storage. For the present risk, the necessary control is: Maintain a versioned approved hardware configuration record for each lifecycle change.
Question 9A remote site wants a two-controller deployment that keeps serving data after one controller fails without relying on an untested single-controller design. What should the administrator implement first to address the underlying gap? Separate local HA requirements from site-disaster-recovery requirements and design an appropriate replicated or MetroCluster-supported solution if needed. Deploy a supported ONTAP HA pair with matching controller roles and verified partner takeover capacity. Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. ExplanationCorrect Answer B:Deploy a supported ONTAP HA pair with matching controller roles and verified partner takeover capacity. The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured. Acceptance requires: Test a controlled takeover and giveback while monitoring client I/O continuity and remaining resource headroom. Other Answers A:Separate local HA requirements from site-disaster-recovery requirements and design an appropriate replicated or MetroCluster-supported solution if needed. This responds to another physical storage systems issue: A geographically isolated site has no practical redundant data-center link, and a plan assumes a second campus will be automatically protected by a standard local HA pair. Its mechanism is: An HA pair addresses controller failure within its supported topology; it does not by itself establish geographically separated disaster recovery. The present case instead requires: Deploy a supported ONTAP HA pair with matching controller roles and verified partner takeover capacity. C:Evaluate an appropriate AFF platform using measured application latency, IOPS and supported capacity requirements before selecting hardware. This responds to another physical storage systems issue: A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. Its mechanism is: All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. The present case instead requires: Deploy a supported ONTAP HA pair with matching controller roles and verified partner takeover capacity. D:Validate the proposed controller, disk shelf, adapter and ONTAP combinations using NetApp Hardware Universe and the Interoperability Matrix before purchase. This responds to another physical storage systems issue: An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. Its mechanism is: Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. The present case instead requires: Deploy a supported ONTAP HA pair with matching controller roles and verified partner takeover capacity.
Question 10A remote site wants a two-controller deployment that keeps serving data after one controller fails without relying on an untested single-controller design. Which storage-system mechanism is the decisive factor in this situation? The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured. An HA pair addresses controller failure within its supported topology; it does not by itself establish geographically separated disaster recovery. All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. ExplanationCorrect Answer A:The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured. The corrective design is: Deploy a supported ONTAP HA pair with matching controller roles and verified partner takeover capacity. A relevant test is: Test a controlled takeover and giveback while monitoring client I/O continuity and remaining resource headroom. Other Answers B:An HA pair addresses controller failure within its supported topology; it does not by itself establish geographically separated disaster recovery. That mechanism fits a different physical storage systems failure: A geographically isolated site has no practical redundant data-center link, and a plan assumes a second campus will be automatically protected by a standard local HA pair. Here the decisive mechanism is: The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured. C:All-flash controller selection targets latency-sensitive random I/O, while capacity alone cannot establish workload fitness. That mechanism fits a different physical storage systems failure: A branch office needs low-latency block storage for a database AND NFS home directories on the same platform, but a proposal chooses a capacity-optimized disk array without measuring either workload or checking protocol fit. Here the decisive mechanism is: The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured. D:Hardware and software component compatibility is constrained by supported configurations, not physical connector fit alone. That mechanism fits a different physical storage systems failure: An organization plans to mix controller and shelf models during a hardware expansion, but the chosen configurations have not been checked for support. Here the decisive mechanism is: The HA partner can assume storage service after a node outage when the pair and its connectivity are properly configured.