Question 500At fictional Glenwood Connectivity 125, a regional service-provider network, during a preproduction design validation, operations observes: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. Which failure consequence follows most closely from ignoring this issue? Traffic leaks or becomes blackholed at the L2/L3 boundary. Customers can inject unapproved Layer 2 traffic into the provider bridge. Customer hosts appear connected yet cannot communicate. A transit route remains unavailable because neighbor behavior is inconsistent. ExplanationCorrect Answer C:Customer hosts appear connected yet cannot communicate. Layer 2 switching forwards traffic within the configured VLAN bridge domain. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Incorrect Answers A:Traffic leaks or becomes blackholed at the L2/L3 boundary. That could help when an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch; here, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. B:Customers can inject unapproved Layer 2 traffic into the provider bridge. This is applicable when an interface permits every customer VLAN tag despite a contract listing only two approved VLANs; the present condition is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. D:A transit route remains unavailable because neighbor behavior is inconsistent. This could help if OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology, but not when hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.
Question 501In a separate fictional JNCIS-SP lab review for Hillside Transit 126, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. What intervention most directly restores the intended routing or switching behavior? Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. Constrain permitted VLAN membership and confirm unauthorized tag handling. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. ExplanationCorrect Answer C:Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. Layer 2 switching forwards traffic within the configured VLAN bridge domain. Incorrect Answers A:Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. This could matter when an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. In this case, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. B:Constrain permitted VLAN membership and confirm unauthorized tag handling. That could help when an interface permits every customer VLAN tag despite a contract listing only two approved VLANs; here, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. D:Configure the supported IPv6 IS-IS family and confirm prefix reachability at intended levels. It is relevant if an IPv6 service prefix is missing from an IS-IS network because the necessary topology and family capability were not enabled, but the reported issue is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.
Question 502In a separate fictional JNCIS-SP lab review for Hillside Transit 126, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. Which networking principle explains why the proposed correction is appropriate? Trunk membership should reflect explicit service authorization, not an unrestricted default. Unexpected MAC movement often points to changing Layer 2 forwarding topology. A tunnel must not rely on its own encapsulated path to reach the outer endpoint. Layer 2 switching forwards traffic within the configured VLAN bridge domain. ExplanationCorrect Answer D:Layer 2 switching forwards traffic within the configured VLAN bridge domain. Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Incorrect Answers A:Trunk membership should reflect explicit service authorization, not an unrestricted default. It addresses a different problem: An interface permits every customer VLAN tag despite a contract listing only two approved VLANs. Here, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. B:Unexpected MAC movement often points to changing Layer 2 forwarding topology. This could matter when a MAC moves rapidly among provider ports after a cabling change, yet troubleshooting focuses only on IP routing tables. In this case, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. C:A tunnel must not rely on its own encapsulated path to reach the outer endpoint. That could help when a route to a GRE destination is learned through the same tunnel, creating recursive or looping resolution; here, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.
Question 503In a separate fictional JNCIS-SP lab review for Hillside Transit 126, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. Which validation result would confirm the design is now functioning? Frame capture shows the intended outer S-tag and unchanged inner customer tag at handoff. Local hosts reach the IRB gateway and authorized routed subnets beyond it. Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. The circuit forms the expected point-to-point adjacency without an unwanted DR election. ExplanationCorrect Answer C:Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Layer 2 switching forwards traffic within the configured VLAN bridge domain. Incorrect Answers A:Frame capture shows the intended outer S-tag and unchanged inner customer tag at handoff. That option concerns provider bridging accidentally rewrites the subscriber VLAN tag when applying an outer service tag. The problem here is different: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. B:Local hosts reach the IRB gateway and authorized routed subnets beyond it. It addresses a different problem: Customers on a bridged VLAN can exchange Layer 2 frames but cannot reach other subnets because the IRB gateway is absent. Here, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. D:The circuit forms the expected point-to-point adjacency without an unwanted DR election. That could help when OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology; here, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.
Question 504In a separate fictional JNCIS-SP lab review for Hillside Transit 126, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. What likely service impact does this condition create? Customer hosts appear connected yet cannot communicate. Unnecessary route changes mask a switching defect and prolong the outage. Excessive flooding consumes bandwidth and exposes traffic across unintended ports. IBGP clients lack complete reachability and use inconsistent exits. ExplanationCorrect Answer A:Customer hosts appear connected yet cannot communicate. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Layer 2 switching forwards traffic within the configured VLAN bridge domain. Incorrect Answers B:Unnecessary route changes mask a switching defect and prolong the outage. That option concerns an operator adds an IP route to fix traffic that never leaves a local bridge domain because its destination MAC is unknown. The problem here is different: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. C:Excessive flooding consumes bandwidth and exposes traffic across unintended ports. It addresses a different problem: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. Here, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. D:IBGP clients lack complete reachability and use inconsistent exits. This could matter when an internal client learns routes from another client only intermittently after the route-reflector peering address changes. In this case, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.
Question 505At fictional Westbridge Exchange 127, a regional service-provider network, during a core-routing acceptance test, operations observes: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. Which configuration or operational correction most directly addresses this failure? Reconcile path MTU with the encapsulation overhead and test representative maximum frames. Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. Associate the gateway with the intended routing and bridging contexts and inspect both tables. Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. ExplanationCorrect Answer B:Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. Ethernet bridges learn source MAC locations to forward known unicast traffic efficiently. The MAC table shows each endpoint on the proper interface and known unicast flooding stops. Incorrect Answers A:Reconcile path MTU with the encapsulation overhead and test representative maximum frames. This addresses a situation in which a service-provider QinQ link carries small frames but drops customer frames when the extra VLAN header exceeds the link MTU; however, an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. C:Associate the gateway with the intended routing and bridging contexts and inspect both tables. That option concerns an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch. The problem here is different: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. D:Apply compatible supported authentication settings on the intended OSPF interfaces and verify adjacency recovery. It addresses a different problem: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. Here, an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port.
Question 506At fictional Westbridge Exchange 127, a regional service-provider network, during a core-routing acceptance test, operations observes: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. Which Junos forwarding or control-plane rule applies to this case? Ethernet bridges learn source MAC locations to forward known unicast traffic efficiently. Bridge-table observations must be interpreted alongside actual physical and logical port membership. Unexpected MAC movement often points to changing Layer 2 forwarding topology. IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. ExplanationCorrect Answer A:Ethernet bridges learn source MAC locations to forward known unicast traffic efficiently. Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. The MAC table shows each endpoint on the proper interface and known unicast flooding stops. Incorrect Answers B:Bridge-table observations must be interpreted alongside actual physical and logical port membership. This addresses a situation in which a MAC is learned on an unexpected aggregation interface following a customer circuit move; however, an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. C:Unexpected MAC movement often points to changing Layer 2 forwarding topology. The choice would be appropriate if a MAC moves rapidly among provider ports after a cabling change, yet troubleshooting focuses only on IP routing tables. Here, an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. D:IS-IS conveys extensible routing attributes in typed TLVs within protocol packets. That option concerns a monitoring parser treats a valid IS-IS reachability TLV as an unsupported fault and pages the operations team. The problem here is different: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port.
Question 507At fictional Westbridge Exchange 127, a regional service-provider network, during a core-routing acceptance test, operations observes: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. What operational evidence best establishes successful remediation? Only the two contracted VLANs are forwarded and other tags are isolated. Two identical inner customer tags remain isolated by separate outer tags or service instances. The MAC table shows each endpoint on the proper interface and known unicast flooding stops. A superior BPDU on the customer link is blocked from changing the intended root. ExplanationCorrect Answer C:The MAC table shows each endpoint on the proper interface and known unicast flooding stops. Ethernet bridges learn source MAC locations to forward known unicast traffic efficiently. Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. Incorrect Answers A:Only the two contracted VLANs are forwarded and other tags are isolated. It is useful for situations where an interface permits every customer VLAN tag despite a contract listing only two approved VLANs; the reported fault, though, is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. B:Two identical inner customer tags remain isolated by separate outer tags or service instances. That relates to circumstances in which two unrelated customers use the same inner VLAN ID, and a template accidentally merges them into one provider bridge. Here the problem is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. D:A superior BPDU on the customer link is blocked from changing the intended root. The choice would be appropriate if a customer-facing bridge advertises a superior root and takes over the provider STP topology. Here, an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port.
Question 508At fictional Westbridge Exchange 127, a regional service-provider network, during a core-routing acceptance test, operations observes: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. Which operational harm would persist without the intended correction? Traffic leaks or becomes blackholed at the L2/L3 boundary. Unnecessary filtering interrupts normal bridged service. A sensitive workload unexpectedly traverses a different core link. Excessive flooding consumes bandwidth and exposes traffic across unintended ports. ExplanationCorrect Answer D:Excessive flooding consumes bandwidth and exposes traffic across unintended ports. Ethernet bridges learn source MAC locations to forward known unicast traffic efficiently. Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. Incorrect Answers A:Traffic leaks or becomes blackholed at the L2/L3 boundary. This relates to a case where an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch; the current situation is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. B:Unnecessary filtering interrupts normal bridged service. It is useful for situations where a customer observes occasional unknown-unicast flooding after long inactivity and assumes every flood is a loop; the reported fault, though, is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. C:A sensitive workload unexpectedly traverses a different core link. That relates to circumstances in which a team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path. Here the problem is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port.
Question 509In a separate fictional JNCIS-SP lab review for Crestland Networks 128, a carrier-edge and core routing team, following a monitored network change window, engineers find: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. What should the Junos specialist change first to resolve this specific fault? Trace member interface and bridge-domain association, then correct the service attachment. Constrain permitted VLAN membership and confirm unauthorized tag handling. Inspect the relevant VSTP instance and set its intended per-VLAN root and port roles. Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. ExplanationCorrect Answer D:Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. The MAC table shows each endpoint on the proper interface and known unicast flooding stops. Ethernet bridges learn source MAC locations to forward known unicast traffic efficiently. Incorrect Answers A:Trace member interface and bridge-domain association, then correct the service attachment. This could help if a MAC is learned on an unexpected aggregation interface following a customer circuit move, but not when an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. B:Constrain permitted VLAN membership and confirm unauthorized tag handling. This relates to a case where an interface permits every customer VLAN tag despite a contract listing only two approved VLANs; the current situation is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. C:Inspect the relevant VSTP instance and set its intended per-VLAN root and port roles. It is useful for situations where one VLAN becomes unavailable after administrators assume the same spanning-tree root applies identically to all VLANs; the reported fault, though, is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port.
Question 510In a separate fictional JNCIS-SP lab review for Crestland Networks 128, a carrier-edge and core routing team, following a monitored network change window, engineers find: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. What technical principle underlies the right remedy? Ethernet bridges learn source MAC locations to forward known unicast traffic efficiently. An Ethernet port's VLAN tagging behavior must match the frames it receives. Customer VLAN IDs are not globally unique and require deliberate provider separation. IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. ExplanationCorrect Answer A:Ethernet bridges learn source MAC locations to forward known unicast traffic efficiently. The MAC table shows each endpoint on the proper interface and known unicast flooding stops. Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. Incorrect Answers B:An Ethernet port's VLAN tagging behavior must match the frames it receives. This could help if a provider access port drops customer tagged frames because it was configured for untagged access mode, but not when an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. C:Customer VLAN IDs are not globally unique and require deliberate provider separation. This relates to a case where two unrelated customers use the same inner VLAN ID, and a template accidentally merges them into one provider bridge; the current situation is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. D:IPv6-over-IPv4 tunnels depend on the transport underlay used to carry encapsulated traffic. It is useful for situations where an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared; the reported fault, though, is that an edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port.