Question 490At fictional Stonefield Telecom 123, a regional service-provider network, during a two-site transit migration, operations observes: A provider access port drops customer tagged frames because it was configured for untagged access mode. Which Junos forwarding or control-plane rule applies to this case? An Ethernet port's VLAN tagging behavior must match the frames it receives. Integrated routing and bridging links a bridge domain to an IP routing gateway. Layer 2 switching forwards traffic within the configured VLAN bridge domain. LDP discovery and the TCP-based LDP session depend on usable transport reachability. ExplanationCorrect Answer A:An Ethernet port's VLAN tagging behavior must match the frames it receives. Match the interface VLAN tagging mode to the customer handoff contract and test ingress frames. Tagged customer frames enter the intended VLAN while disallowed tags are rejected. Incorrect Answers B:Integrated routing and bridging links a bridge domain to an IP routing gateway. This could matter when customers on a bridged VLAN can exchange Layer 2 frames but cannot reach other subnets because the IRB gateway is absent. In this case, a provider access port drops customer tagged frames because it was configured for untagged access mode. C:Layer 2 switching forwards traffic within the configured VLAN bridge domain. That could help when hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier; here, a provider access port drops customer tagged frames because it was configured for untagged access mode. D:LDP discovery and the TCP-based LDP session depend on usable transport reachability. This is applicable when two core routers cannot form an LDP session even though they discover one another on the connected link; the present condition is that a provider access port drops customer tagged frames because it was configured for untagged access mode.
Question 491At fictional Stonefield Telecom 123, a regional service-provider network, during a two-site transit migration, operations observes: A provider access port drops customer tagged frames because it was configured for untagged access mode. What operational evidence best establishes successful remediation? The tenant VLAN reaches only its intended IRB gateway and routing-instance routes. Frame capture shows the intended outer S-tag and unchanged inner customer tag at handoff. The suspect port remains in the protected state until valid BPDU information returns. Tagged customer frames enter the intended VLAN while disallowed tags are rejected. ExplanationCorrect Answer D:Tagged customer frames enter the intended VLAN while disallowed tags are rejected. An Ethernet port's VLAN tagging behavior must match the frames it receives. Match the interface VLAN tagging mode to the customer handoff contract and test ingress frames. Incorrect Answers A:The tenant VLAN reaches only its intended IRB gateway and routing-instance routes. That option concerns an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch. The problem here is different: A provider access port drops customer tagged frames because it was configured for untagged access mode. B:Frame capture shows the intended outer S-tag and unchanged inner customer tag at handoff. It addresses a different problem: Provider bridging accidentally rewrites the subscriber VLAN tag when applying an outer service tag. Here, a provider access port drops customer tagged frames because it was configured for untagged access mode. C:The suspect port remains in the protected state until valid BPDU information returns. This could matter when a blocked redundant link unexpectedly starts forwarding when BPDUs cease on a faulty remote bridge. In this case, a provider access port drops customer tagged frames because it was configured for untagged access mode.
Question 492At fictional Stonefield Telecom 123, a regional service-provider network, during a two-site transit migration, operations observes: A provider access port drops customer tagged frames because it was configured for untagged access mode. Which operational harm would persist without the intended correction? Traffic follows an obsolete service path or reaches the wrong customer site. Customer broadcasts and potentially sensitive frames cross service boundaries. Customer Layer 2 service fails despite healthy physical link status. Expired topology data causes periodic loss of service routes. ExplanationCorrect Answer C:Customer Layer 2 service fails despite healthy physical link status. An Ethernet port's VLAN tagging behavior must match the frames it receives. Match the interface VLAN tagging mode to the customer handoff contract and test ingress frames. Incorrect Answers A:Traffic follows an obsolete service path or reaches the wrong customer site. The choice would be appropriate if a MAC is learned on an unexpected aggregation interface following a customer circuit move. Here, a provider access port drops customer tagged frames because it was configured for untagged access mode. B:Customer broadcasts and potentially sensitive frames cross service boundaries. That option concerns two customer VLANs merge unexpectedly after a virtual-switch template is copied across separate services. The problem here is different: A provider access port drops customer tagged frames because it was configured for untagged access mode. D:Expired topology data causes periodic loss of service routes. This could matter when an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets. In this case, a provider access port drops customer tagged frames because it was configured for untagged access mode.
Question 493In a separate fictional JNCIS-SP lab review for Clearwater Peering 124, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A provider access port drops customer tagged frames because it was configured for untagged access mode. What should the Junos specialist change first to resolve this specific fault? Match the interface VLAN tagging mode to the customer handoff contract and test ingress frames. Investigate Layer 2 topology, bridge membership and possible loop before route-policy changes. Trace member interface and bridge-domain association, then correct the service attachment. Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. ExplanationCorrect Answer A:Match the interface VLAN tagging mode to the customer handoff contract and test ingress frames. Tagged customer frames enter the intended VLAN while disallowed tags are rejected. An Ethernet port's VLAN tagging behavior must match the frames it receives. Incorrect Answers B:Investigate Layer 2 topology, bridge membership and possible loop before route-policy changes. The choice would be appropriate if a MAC moves rapidly among provider ports after a cabling change, yet troubleshooting focuses only on IP routing tables. Here, a provider access port drops customer tagged frames because it was configured for untagged access mode. C:Trace member interface and bridge-domain association, then correct the service attachment. That option concerns a MAC is learned on an unexpected aggregation interface following a customer circuit move. The problem here is different: A provider access port drops customer tagged frames because it was configured for untagged access mode. D:Enable the intended IPv6 OSPFv3 configuration and verify neighbor and route state. It addresses a different problem: An IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Here, a provider access port drops customer tagged frames because it was configured for untagged access mode.
Question 494In a separate fictional JNCIS-SP lab review for Clearwater Peering 124, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A provider access port drops customer tagged frames because it was configured for untagged access mode. What technical principle underlies the right remedy? An Ethernet port's VLAN tagging behavior must match the frames it receives. Layer 2 bridges select egress ports using MAC/VLAN information before any routed-hop lookup. IRB traffic must bridge and route within an intentionally consistent service context. IS-IS elects a designated intermediate system on broadcast networks to manage pseudonode representation. ExplanationCorrect Answer A:An Ethernet port's VLAN tagging behavior must match the frames it receives. Tagged customer frames enter the intended VLAN while disallowed tags are rejected. Match the interface VLAN tagging mode to the customer handoff contract and test ingress frames. Incorrect Answers B:Layer 2 bridges select egress ports using MAC/VLAN information before any routed-hop lookup. This addresses a situation in which an operator adds an IP route to fix traffic that never leaves a local bridge domain because its destination MAC is unknown; however, a provider access port drops customer tagged frames because it was configured for untagged access mode. C:IRB traffic must bridge and route within an intentionally consistent service context. The choice would be appropriate if an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch. Here, a provider access port drops customer tagged frames because it was configured for untagged access mode. D:IS-IS elects a designated intermediate system on broadcast networks to manage pseudonode representation. That option concerns operators see two possible LAN-designated routers and assume the wrong one leads routing for the shared segment. The problem here is different: A provider access port drops customer tagged frames because it was configured for untagged access mode.
Question 495In a separate fictional JNCIS-SP lab review for Clearwater Peering 124, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A provider access port drops customer tagged frames because it was configured for untagged access mode. Which acceptance finding demonstrates the affected service has recovered? Local hosts reach the IRB gateway and authorized routed subnets beyond it. A correctly sized customer frame traverses the entire provider handoff without drops. Tagged customer frames enter the intended VLAN while disallowed tags are rejected. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. ExplanationCorrect Answer C:Tagged customer frames enter the intended VLAN while disallowed tags are rejected. Match the interface VLAN tagging mode to the customer handoff contract and test ingress frames. An Ethernet port's VLAN tagging behavior must match the frames it receives. Incorrect Answers A:Local hosts reach the IRB gateway and authorized routed subnets beyond it. It is useful for situations where customers on a bridged VLAN can exchange Layer 2 frames but cannot reach other subnets because the IRB gateway is absent; the reported fault, though, is that a provider access port drops customer tagged frames because it was configured for untagged access mode. B:A correctly sized customer frame traverses the entire provider handoff without drops. That relates to circumstances in which a service-provider QinQ link carries small frames but drops customer frames when the extra VLAN header exceeds the link MTU. Here the problem is that a provider access port drops customer tagged frames because it was configured for untagged access mode. D:OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. The choice would be appropriate if an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted. Here, a provider access port drops customer tagged frames because it was configured for untagged access mode.
Question 496In a separate fictional JNCIS-SP lab review for Clearwater Peering 124, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A provider access port drops customer tagged frames because it was configured for untagged access mode. What is the direct residual network risk if the fault remains unresolved? Customer Layer 2 service fails despite healthy physical link status. Customer broadcasts and potentially sensitive frames cross service boundaries. Customer hosts appear connected yet cannot communicate. Customer switching devices can influence provider spanning-tree topology. ExplanationCorrect Answer A:Customer Layer 2 service fails despite healthy physical link status. Match the interface VLAN tagging mode to the customer handoff contract and test ingress frames. An Ethernet port's VLAN tagging behavior must match the frames it receives. Incorrect Answers B:Customer broadcasts and potentially sensitive frames cross service boundaries. It is useful for situations where two customer VLANs merge unexpectedly after a virtual-switch template is copied across separate services; the reported fault, though, is that a provider access port drops customer tagged frames because it was configured for untagged access mode. C:Customer hosts appear connected yet cannot communicate. That relates to circumstances in which hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. Here the problem is that a provider access port drops customer tagged frames because it was configured for untagged access mode. D:Customer switching devices can influence provider spanning-tree topology. This addresses a situation in which a subscriber accidentally connects a switch that sends BPDUs into a provider edge expected to accept endpoints only; however, a provider access port drops customer tagged frames because it was configured for untagged access mode.
Question 497At fictional Glenwood Connectivity 125, a regional service-provider network, during a preproduction design validation, operations observes: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. Which targeted remediation best fits the reported behavior? Use distinct virtual-switch or bridge-domain contexts with explicit interface membership. Investigate Layer 2 topology, bridge membership and possible loop before route-policy changes. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Set compatible network type and review adjacency expectations on both ends. ExplanationCorrect Answer C:Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Layer 2 switching forwards traffic within the configured VLAN bridge domain. Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. Incorrect Answers A:Use distinct virtual-switch or bridge-domain contexts with explicit interface membership. This could help if two customer VLANs merge unexpectedly after a virtual-switch template is copied across separate services, but not when hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. B:Investigate Layer 2 topology, bridge membership and possible loop before route-policy changes. This relates to a case where a MAC moves rapidly among provider ports after a cabling change, yet troubleshooting focuses only on IP routing tables; the current situation is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. D:Set compatible network type and review adjacency expectations on both ends. That relates to circumstances in which OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology. Here the problem is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.
Question 498At fictional Glenwood Connectivity 125, a regional service-provider network, during a preproduction design validation, operations observes: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. Why is this particular correction the best fit for the stated defect? Bridge-table observations must be interpreted alongside actual physical and logical port membership. An Ethernet port's VLAN tagging behavior must match the frames it receives. Layer 2 switching forwards traffic within the configured VLAN bridge domain. MPLS ingress typically pushes a label, transit nodes swap, and egress behavior may remove it. ExplanationCorrect Answer C:Layer 2 switching forwards traffic within the configured VLAN bridge domain. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. Incorrect Answers A:Bridge-table observations must be interpreted alongside actual physical and logical port membership. It is relevant if a MAC is learned on an unexpected aggregation interface following a customer circuit move, but the reported issue is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. B:An Ethernet port's VLAN tagging behavior must match the frames it receives. This could help if a provider access port drops customer tagged frames because it was configured for untagged access mode, but not when hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. D:MPLS ingress typically pushes a label, transit nodes swap, and egress behavior may remove it. It is useful for situations where a network test expects the ingress PE to swap a label that it should actually impose; the reported fault, though, is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.
Question 499At fictional Glenwood Connectivity 125, a regional service-provider network, during a preproduction design validation, operations observes: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. What direct observation would prove the corrective action worked? Local hosts reach the IRB gateway and authorized routed subnets beyond it. Two identical inner customer tags remain isolated by separate outer tags or service instances. The route table and forwarding lookup show the expected metric-driven next hop. Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. ExplanationCorrect Answer D:Both client MACs appear in the intended VLAN and bidirectional frames traverse the switch. Layer 2 switching forwards traffic within the configured VLAN bridge domain. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Incorrect Answers A:Local hosts reach the IRB gateway and authorized routed subnets beyond it. This is applicable when customers on a bridged VLAN can exchange Layer 2 frames but cannot reach other subnets because the IRB gateway is absent; the present condition is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. B:Two identical inner customer tags remain isolated by separate outer tags or service instances. It is relevant if two unrelated customers use the same inner VLAN ID, and a template accidentally merges them into one provider bridge, but the reported issue is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. C:The route table and forwarding lookup show the expected metric-driven next hop. This could help if the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change, but not when hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.
Question 500At fictional Glenwood Connectivity 125, a regional service-provider network, during a preproduction design validation, operations observes: Hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. Which failure consequence follows most closely from ignoring this issue? Traffic leaks or becomes blackholed at the L2/L3 boundary. Customers can inject unapproved Layer 2 traffic into the provider bridge. Customer hosts appear connected yet cannot communicate. A transit route remains unavailable because neighbor behavior is inconsistent. ExplanationCorrect Answer C:Customer hosts appear connected yet cannot communicate. Layer 2 switching forwards traffic within the configured VLAN bridge domain. Correct permitted VLAN membership on both logical ports and validate MAC learning in the same broadcast domain. Incorrect Answers A:Traffic leaks or becomes blackholed at the L2/L3 boundary. That could help when an IRB gateway is placed in the default routing instance while its tenant VLAN belongs to a separate virtual switch; here, hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. B:Customers can inject unapproved Layer 2 traffic into the provider bridge. This is applicable when an interface permits every customer VLAN tag despite a contract listing only two approved VLANs; the present condition is that hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier. D:A transit route remains unavailable because neighbor behavior is inconsistent. This could help if OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology, but not when hosts connected through a service-provider switch cannot exchange traffic because each port references a different VLAN identifier.