Question 910 A technician has authorization to fix the issue: Two Ethernet ports repeatedly transition up and down when a damaged cable is flexed, causing short network outages. What action should be taken next? Shorten or redesign the copper run and certify the installed cabling Move critical clients to an appropriate band or change location and channel plan Configure compatible auto-negotiation or matching approved duplex settings on both ends Replace the defective cable and verify stable link status and error counters Explanation Correct Answer D:Switch interface logs show repeated link-state transitions correlated with cable movement, consistent with a link flapping caused by physical cabling fault. Incorrect Answers A:Cable certification shows the run exceeds the supported channel length and has failing attenuation results, consistent with a copper link impairment from excessive cable length. B:Spectrum activity rises near the microwave and the problem disappears when it is off, consistent with an external 2.4 ghz radio-frequency interference. C:Interface counters show late collisions or FCS errors and duplex settings differ on link partners, consistent with an ethernet duplex mismatch.
Question 911 A long copper Ethernet run connects at a slower rate and produces CRC errors near the maximum cable-length limit. Which repair or configuration change addresses the underlying problem? Review approved VPN routing and choose a more direct supported gateway path Replace the defective cable and verify stable link status and error counters Configure compatible auto-negotiation or matching approved duplex settings on both ends Shorten or redesign the copper run and certify the installed cabling Explanation Correct Answer D:Cable certification shows the run exceeds the supported channel length and has failing attenuation results, consistent with a copper link impairment from excessive cable length. Incorrect Answers A:Round-trip time rises at the remote gateway despite low local LAN latency, consistent with an excessive route latency from indirect network path. B:Switch interface logs show repeated link-state transitions correlated with cable movement, consistent with a link flapping caused by physical cabling fault. C:Interface counters show late collisions or FCS errors and duplex settings differ on link partners, consistent with an ethernet duplex mismatch.
Question 912 A maintenance window is available for the following problem: An office reports slow one-way file transfers after replacing a managed switch; one port is forced full duplex while its peer is half duplex. Which intervention is most appropriate? Configure compatible auto-negotiation or matching approved duplex settings on both ends Shorten or redesign the copper run and certify the installed cabling Use appropriate QoS and schedule bulk backups to preserve latency-sensitive traffic Restore the approved port VLAN and verify default gateway and segmentation rules Explanation Correct Answer A:Interface counters show late collisions or FCS errors and duplex settings differ on link partners, consistent with an ethernet duplex mismatch. Incorrect Answers B:Cable certification shows the run exceeds the supported channel length and has failing attenuation results, consistent with a copper link impairment from excessive cable length. C:Packet drops and voice degradation coincide with saturated outbound bandwidth, consistent with a wan congestion without voip quality-of-service prioritization. D:The switch port's configured VLAN ID does not match the intended user network, consistent with an incorrect switch access vlan assignment.
Question 913 The owner wants a specific repair, not merely more monitoring: A VPN user's connection is reachable but suffers long page-load delays; traceroute and monitoring show an unusually long path through distant gateways. What should the technician do? Shorten or redesign the copper run and certify the installed cabling Review approved VPN routing and choose a more direct supported gateway path Restore the trusted certificate chain and correct managed Wi-Fi profile settings Configure the correct gateway and verify a routed path with controlled probes Explanation Correct Answer B:Round-trip time rises at the remote gateway despite low local LAN latency, consistent with an excessive route latency from indirect network path. Incorrect Answers A:Cable certification shows the run exceeds the supported channel length and has failing attenuation results, consistent with a copper link impairment from excessive cable length. C:802.1X logs show the client rejects the RADIUS server certificate chain, consistent with an enterprise wi-fi certificate validation failure. D:The first-hop gateway cannot be ARPed on the local network but other hosts use a different router address, consistent with an incorrect default route to external subnets.
Question 914 An employee can join the office Wi-Fi but every attempt to access the protected network fails with a certificate trust error. Which solution addresses the cause without unnecessary unrelated changes? Restore the approved port VLAN and verify default gateway and segmentation rules Review approved VPN routing and choose a more direct supported gateway path Restore the trusted certificate chain and correct managed Wi-Fi profile settings Restore the correct relay or VLAN path and verify scope availability Explanation Correct Answer C:802.1X logs show the client rejects the RADIUS server certificate chain, consistent with an enterprise wi-fi certificate validation failure. Incorrect Answers A:The switch port's configured VLAN ID does not match the intended user network, consistent with an incorrect switch access vlan assignment. B:Round-trip time rises at the remote gateway despite low local LAN latency, consistent with an excessive route latency from indirect network path. D:Lease requests from the affected VLAN do not arrive at the central DHCP service, consistent with a dhcp relay or vlan reachability failure.
Question 915 A laptop can communicate with devices on its access VLAN but not with a server on another floor after its switch port was moved to a new VLAN. Which corrective action is the safest and most direct response? Restore the correct relay or VLAN path and verify scope availability Configure compatible auto-negotiation or matching approved duplex settings on both ends Configure the correct gateway and verify a routed path with controlled probes Restore the approved port VLAN and verify default gateway and segmentation rules Explanation Correct Answer D:The switch port's configured VLAN ID does not match the intended user network, consistent with an incorrect switch access vlan assignment. Incorrect Answers A:Lease requests from the affected VLAN do not arrive at the central DHCP service, consistent with a dhcp relay or vlan reachability failure. B:Interface counters show late collisions or FCS errors and duplex settings differ on link partners, consistent with an ethernet duplex mismatch. C:The first-hop gateway cannot be ARPed on the local network but other hosts use a different router address, consistent with an incorrect default route to external subnets.
Question 916 A technician has authorization to fix the issue: A workstation has a correct static IP and subnet mask but no route to external networks because the configured default router IP is wrong. What action should be taken next? Restore the approved port VLAN and verify default gateway and segmentation rules Configure the correct gateway and verify a routed path with controlled probes Restore the supported IPv6 router advertisements and verify the default route Review approved VPN routing and choose a more direct supported gateway path Explanation Correct Answer B:The first-hop gateway cannot be ARPed on the local network but other hosts use a different router address, consistent with an incorrect default route to external subnets. Incorrect Answers A:The switch port's configured VLAN ID does not match the intended user network, consistent with an incorrect switch access vlan assignment. C:The hosts have no learned global router even though their network interfaces show link-local IPv6, consistent with an ipv6 router advertisement or default-route loss. D:Round-trip time rises at the remote gateway despite low local LAN latency, consistent with an excessive route latency from indirect network path.
Question 917 Several IPv6 clients can reach neighbors with link-local addresses but have no valid route to a public IPv6 website. Which repair or configuration change addresses the underlying problem? Configure the correct gateway and verify a routed path with controlled probes Secure and realign the customer radio under safe access procedures and verify signal levels Restore the supported IPv6 router advertisements and verify the default route Review approved VPN routing and choose a more direct supported gateway path Explanation Correct Answer C:The hosts have no learned global router even though their network interfaces show link-local IPv6, consistent with an ipv6 router advertisement or default-route loss. Incorrect Answers A:The first-hop gateway cannot be ARPed on the local network but other hosts use a different router address, consistent with an incorrect default route to external subnets. B:The ISP radio signal and error rate worsen as the outdoor mount moves in wind, consistent with an unstable fixed wireless line-of-sight alignment. D:Round-trip time rises at the remote gateway despite low local LAN latency, consistent with an excessive route latency from indirect network path.
Question 918 A maintenance window is available for the following problem: A small firm's network works each morning but loses WAN access each evening when its fixed wireless antenna shifts in high wind. Which intervention is most appropriate? Restore the supported IPv6 router advertisements and verify the default route Secure and realign the customer radio under safe access procedures and verify signal levels Configure the correct gateway and verify a routed path with controlled probes Use appropriate QoS and schedule bulk backups to preserve latency-sensitive traffic Explanation Correct Answer B:The ISP radio signal and error rate worsen as the outdoor mount moves in wind, consistent with an unstable fixed wireless line-of-sight alignment. Incorrect Answers A:The hosts have no learned global router even though their network interfaces show link-local IPv6, consistent with an ipv6 router advertisement or default-route loss. C:The first-hop gateway cannot be ARPed on the local network but other hosts use a different router address, consistent with an incorrect default route to external subnets. D:Packet drops and voice degradation coincide with saturated outbound bandwidth, consistent with a wan congestion without voip quality-of-service prioritization.
Question 919 The owner wants a specific repair, not merely more monitoring: A VoIP deployment loses voice packets while file transfers saturate the uplink during office backups. What should the technician do? Configure compatible auto-negotiation or matching approved duplex settings on both ends Secure and realign the customer radio under safe access procedures and verify signal levels Use appropriate QoS and schedule bulk backups to preserve latency-sensitive traffic Apply supported QoS and investigate the variable-delay path with jitter measurements Explanation Correct Answer C:Packet drops and voice degradation coincide with saturated outbound bandwidth, consistent with a wan congestion without voip quality-of-service prioritization. Incorrect Answers A:Interface counters show late collisions or FCS errors and duplex settings differ on link partners, consistent with an ethernet duplex mismatch. B:The ISP radio signal and error rate worsen as the outdoor mount moves in wind, consistent with an unstable fixed wireless line-of-sight alignment. D:RTP monitoring shows large variations in packet interarrival time rather than sustained congestion, consistent with a packet jitter harms real-time voip.
Question 920 A shared office printer jams repeatedly at the same feeder corner and its paper-size guides are set for a wider tray than the actual paper. Which solution addresses the cause without unnecessary unrelated changes? Seat or repair the tray and sensor, then confirm it appears in printer settings Align guides for the correct paper size and clear the jam using the approved path Install the compatible driver and correct queue configuration, then test sample files Investigate and safely clear or restart the specific print queue and verify the spooler Explanation Correct Answer B:Sheets skew into the pickup path and the paper guides do not touch the loaded stack correctly, consistent with a paper-feed guide misalignment. Incorrect Answers A:Removing and reseating the tray changes the sensor state while the tray's paper guides are correct, consistent with a paper tray detection sensor not actuated. C:The server sends a page-description format unsupported by the target printer model, consistent with a printer driver language mismatch. D:The local device prints independently while the server's queued jobs remain stuck, consistent with a frozen print queue or spooler path.