Question 980At fictional Orchard Link 245, a regional service-provider network, during a preproduction design validation, operations observes: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. Which failure consequence follows most closely from ignoring this issue? Maintenance triggers avoidable traffic loss and prolonged recovery. Customers experience extended blackholes before alternate paths take over. Traffic is blackholed because neighbors keep invalid routes or fail to assist recovery. Duplicate identity creates conflicting LSPs and unstable route computation. ExplanationCorrect Answer B:Customers experience extended blackholes before alternate paths take over. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. Incorrect Answers A:Maintenance triggers avoidable traffic loss and prolonged recovery. That could help when a planned Routing Engine switchover resets forwarding unexpectedly because chassis graceful switchover was not prepared; here, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. C:Traffic is blackholed because neighbors keep invalid routes or fail to assist recovery. It is relevant if a provider assumes graceful restart will work during a routing process restart without considering neighbor support, but the reported issue is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. D:Duplicate identity creates conflicting LSPs and unstable route computation. This could help if a device cloned from a lab template has the same IS-IS system ID as a production router, but not when a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.
Question 981In a separate fictional JNCIS-SP lab review for Oakshore Peering 246, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. What intervention most directly restores the intended routing or switching behavior? Enable and verify supported nonstop active routing with required redundancy prerequisites. Correct VRRP group association, priority, and failover behavior on the gateway pair. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. ExplanationCorrect Answer C:Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. A controlled path failure produces the designed BFD event and route withdrawal within target bounds. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Incorrect Answers A:Enable and verify supported nonstop active routing with required redundancy prerequisites. This could matter when traffic briefly vanishes after a Routing Engine failure because the backup does not maintain protocol state. In this case, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. B:Correct VRRP group association, priority, and failover behavior on the gateway pair. That could help when an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect; here, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. D:Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. It is relevant if an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets, but the reported issue is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.
Question 982In a separate fictional JNCIS-SP lab review for Oakshore Peering 246, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. Which networking principle explains why the proposed correction is appropriate? BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. NSR maintains routing protocol information on the backup Routing Engine beyond basic GRES forwarding preservation. A link aggregation group forwards correctly only over members meeting the operational bundle requirements. LDP discovery and the TCP-based LDP session depend on usable transport reachability. ExplanationCorrect Answer A:BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. A controlled path failure produces the designed BFD event and route withdrawal within target bounds. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. Incorrect Answers B:NSR maintains routing protocol information on the backup Routing Engine beyond basic GRES forwarding preservation. This could matter when traffic briefly vanishes after a Routing Engine failure because the backup does not maintain protocol state. In this case, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. C:A link aggregation group forwards correctly only over members meeting the operational bundle requirements. That could help when a bundled uplink has two configured members but only one is usable because the second member's operational parameters differ; here, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. D:LDP discovery and the TCP-based LDP session depend on usable transport reachability. This is applicable when two core routers cannot form an LDP session even though they discover one another on the connected link; the present condition is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.
Question 983In a separate fictional JNCIS-SP lab review for Oakshore Peering 246, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. Which validation result would confirm the design is now functioning? The backup Routing Engine becomes active and forwarding remains within the accepted interruption budget. Peers retain valid routes during a tested restart and withdraw stale state after the appropriate interval. The authorized IPv6 prefixes arrive in the intended inet6 table without IPv4 policy changes. A controlled path failure produces the designed BFD event and route withdrawal within target bounds. ExplanationCorrect Answer D:A controlled path failure produces the designed BFD event and route withdrawal within target bounds. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Incorrect Answers A:The backup Routing Engine becomes active and forwarding remains within the accepted interruption budget. That option concerns a planned Routing Engine switchover resets forwarding unexpectedly because chassis graceful switchover was not prepared. The problem here is different: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. B:Peers retain valid routes during a tested restart and withdraw stale state after the appropriate interval. It addresses a different problem: A provider assumes graceful restart will work during a routing process restart without considering neighbor support. Here, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. C:The authorized IPv6 prefixes arrive in the intended inet6 table without IPv4 policy changes. This could matter when an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter. In this case, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.
Question 984In a separate fictional JNCIS-SP lab review for Oakshore Peering 246, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. What likely service impact does this condition create? A supervisor failure forces routing protocol reconvergence and drops customer traffic. Customers experience extended blackholes before alternate paths take over. A single gateway device fault disconnects all hosts on the VLAN. IPv6 customers lose service even when IPv4 routing remains healthy. ExplanationCorrect Answer B:Customers experience extended blackholes before alternate paths take over. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Incorrect Answers A:A supervisor failure forces routing protocol reconvergence and drops customer traffic. The choice would be appropriate if traffic briefly vanishes after a Routing Engine failure because the backup does not maintain protocol state. Here, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. C:A single gateway device fault disconnects all hosts on the VLAN. It addresses a different problem: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. Here, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. D:IPv6 customers lose service even when IPv4 routing remains healthy. This could matter when an IPv6 service prefix is configured with a next-hop address that does not resolve on the intended transit interface. In this case, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.
Question 985At fictional Brookridge Metro 247, a regional service-provider network, during a core-routing acceptance test, operations observes: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. Which configuration or operational correction most directly addresses this failure? Correct VRRP group association, priority, and failover behavior on the gateway pair. Align supported member configuration and verify aggregation state and distributed traffic. Measure end-to-end service continuity while exercising the planned HA transition and inspect forwarding state. Inspect label stack, bottom-of-stack indicator, and the expected transport operation. ExplanationCorrect Answer A:Correct VRRP group association, priority, and failover behavior on the gateway pair. VRRP provides a shared virtual gateway address with an active router and standby candidates. The backup becomes master during a controlled failure and hosts retain gateway reachability. Incorrect Answers B:Align supported member configuration and verify aggregation state and distributed traffic. The choice would be appropriate if a bundled uplink has two configured members but only one is usable because the second member's operational parameters differ. Here, an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. C:Measure end-to-end service continuity while exercising the planned HA transition and inspect forwarding state. That option concerns an availability test is signed off because BFD and VRRP report healthy, but customer packets still drop during failover. The problem here is different: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. D:Inspect label stack, bottom-of-stack indicator, and the expected transport operation. It addresses a different problem: Operations assumes a packet is plain IP because the capture display does not decode its MPLS shim header. Here, an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect.
Question 986At fictional Brookridge Metro 247, a regional service-provider network, during a core-routing acceptance test, operations observes: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. Which Junos forwarding or control-plane rule applies to this case? LAG availability depends on traffic being redirected to healthy active members after failure. Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. VRRP provides a shared virtual gateway address with an active router and standby candidates. Route reflectors distribute selected IBGP reachability within the configured client topology. ExplanationCorrect Answer C:VRRP provides a shared virtual gateway address with an active router and standby candidates. Correct VRRP group association, priority, and failover behavior on the gateway pair. The backup becomes master during a controlled failure and hosts retain gateway reachability. Incorrect Answers A:LAG availability depends on traffic being redirected to healthy active members after failure. That relates to circumstances in which a provider assumes a two-member LAG is redundant but has never checked forwarding when one member fails. Here the problem is that an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. B:Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. This addresses a situation in which a provider assumes graceful restart will work during a routing process restart without considering neighbor support; however, an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. D:Route reflectors distribute selected IBGP reachability within the configured client topology. That option concerns an internal client learns routes from another client only intermittently after the route-reflector peering address changes. The problem here is different: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect.
Question 987At fictional Brookridge Metro 247, a regional service-provider network, during a core-routing acceptance test, operations observes: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. What operational evidence best establishes successful remediation? Loss of one link leaves the logical bundle up and service traffic continues on the other. The backup becomes master during a controlled failure and hosts retain gateway reachability. MAC tables and customer bridge forwarding remain stable during controlled switchover. Packet observations match the intended push, swap, and disposition stages. ExplanationCorrect Answer B:The backup becomes master during a controlled failure and hosts retain gateway reachability. VRRP provides a shared virtual gateway address with an active router and standby candidates. Correct VRRP group association, priority, and failover behavior on the gateway pair. Incorrect Answers A:Loss of one link leaves the logical bundle up and service traffic continues on the other. It is useful for situations where a provider assumes a two-member LAG is redundant but has never checked forwarding when one member fails; the reported fault, though, is that an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. C:MAC tables and customer bridge forwarding remain stable during controlled switchover. This addresses a situation in which a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets; however, an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. D:Packet observations match the intended push, swap, and disposition stages. The choice would be appropriate if a network test expects the ingress PE to swap a label that it should actually impose. Here, an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect.
Question 988At fictional Brookridge Metro 247, a regional service-provider network, during a core-routing acceptance test, operations observes: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. Which operational harm would persist without the intended correction? A single gateway device fault disconnects all hosts on the VLAN. A nominally redundant network fails its practical customer continuity requirement. Maintenance triggers avoidable traffic loss and prolonged recovery. The monitoring function loses required reachability or isolation is weakened by broad route copying. ExplanationCorrect Answer A:A single gateway device fault disconnects all hosts on the VLAN. VRRP provides a shared virtual gateway address with an active router and standby candidates. Correct VRRP group association, priority, and failover behavior on the gateway pair. Incorrect Answers B:A nominally redundant network fails its practical customer continuity requirement. It is useful for situations where an availability test is signed off because BFD and VRRP report healthy, but customer packets still drop during failover; the reported fault, though, is that an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. C:Maintenance triggers avoidable traffic loss and prolonged recovery. That relates to circumstances in which a planned Routing Engine switchover resets forwarding unexpectedly because chassis graceful switchover was not prepared. Here the problem is that an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. D:The monitoring function loses required reachability or isolation is weakened by broad route copying. This addresses a situation in which a route intended for a monitoring routing table is missing because the RIB group does not include the recipient table; however, an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect.
Question 989In a separate fictional JNCIS-SP lab review for Stonefield Telecom 248, a carrier-edge and core routing team, following a monitored network change window, engineers find: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. What should the Junos specialist change first to resolve this specific fault? Measure end-to-end service continuity while exercising the planned HA transition and inspect forwarding state. Run a controlled member failure test and verify surviving-link service forwarding. Assign planned bridge priorities and verify root and alternate port roles. Correct VRRP group association, priority, and failover behavior on the gateway pair. ExplanationCorrect Answer D:Correct VRRP group association, priority, and failover behavior on the gateway pair. The backup becomes master during a controlled failure and hosts retain gateway reachability. VRRP provides a shared virtual gateway address with an active router and standby candidates. Incorrect Answers A:Measure end-to-end service continuity while exercising the planned HA transition and inspect forwarding state. This could help if an availability test is signed off because BFD and VRRP report healthy, but customer packets still drop during failover, but not when an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. B:Run a controlled member failure test and verify surviving-link service forwarding. This relates to a case where a provider assumes a two-member LAG is redundant but has never checked forwarding when one member fails; the current situation is that an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. C:Assign planned bridge priorities and verify root and alternate port roles. It is useful for situations where a low-capacity access switch becomes STP root after a new bridge priority setting; the reported fault, though, is that an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect.
Question 990In a separate fictional JNCIS-SP lab review for Stonefield Telecom 248, a carrier-edge and core routing team, following a monitored network change window, engineers find: An access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. What technical principle underlies the right remedy? VRRP provides a shared virtual gateway address with an active router and standby candidates. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. Martian route handling protects the routing table from addresses that should not be treated as normally reachable. ExplanationCorrect Answer A:VRRP provides a shared virtual gateway address with an active router and standby candidates. The backup becomes master during a controlled failure and hosts retain gateway reachability. Correct VRRP group association, priority, and failover behavior on the gateway pair. Incorrect Answers B:BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. This could help if a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow, but not when an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. C:Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. This relates to a case where a provider assumes graceful restart will work during a routing process restart without considering neighbor support; the current situation is that an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. D:Martian route handling protects the routing table from addresses that should not be treated as normally reachable. It is useful for situations where a router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing; the reported fault, though, is that an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect.