Question 970At fictional Brightstone Backbone 243, a regional service-provider network, during a two-site transit migration, operations observes: A switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. Which Junos forwarding or control-plane rule applies to this case? NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. VRRP provides a shared virtual gateway address with an active router and standby candidates. Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. IPv4 and IPv6 route lookups use separate address-family tables. ExplanationCorrect Answer A:NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. MAC tables and customer bridge forwarding remain stable during controlled switchover. Incorrect Answers B:VRRP provides a shared virtual gateway address with an active router and standby candidates. This could matter when an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. In this case, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. C:Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. That could help when a provider assumes graceful restart will work during a routing process restart without considering neighbor support; here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. D:IPv4 and IPv6 route lookups use separate address-family tables. This is applicable when a support engineer runs an IPv4 route lookup for an IPv6 destination and concludes the destination is not advertised; the present condition is that a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets.
Question 971At fictional Brightstone Backbone 243, a regional service-provider network, during a two-site transit migration, operations observes: A switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. What operational evidence best establishes successful remediation? The backup Routing Engine becomes active and forwarding remains within the accepted interruption budget. Peers retain valid routes during a tested restart and withdraw stale state after the appropriate interval. MAC tables and customer bridge forwarding remain stable during controlled switchover. Route detail shows intended local preference values and traffic exits through the designated link. ExplanationCorrect Answer C:MAC tables and customer bridge forwarding remain stable during controlled switchover. NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. Incorrect Answers A:The backup Routing Engine becomes active and forwarding remains within the accepted interruption budget. That option concerns a planned Routing Engine switchover resets forwarding unexpectedly because chassis graceful switchover was not prepared. The problem here is different: A switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. B:Peers retain valid routes during a tested restart and withdraw stale state after the appropriate interval. It addresses a different problem: A provider assumes graceful restart will work during a routing process restart without considering neighbor support. Here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. D:Route detail shows intended local preference values and traffic exits through the designated link. That could help when a customer AS should prefer a primary exit but its IBGP paths have the same local preference after a policy reset; here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets.
Question 972At fictional Brightstone Backbone 243, a regional service-provider network, during a two-site transit migration, operations observes: A switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. Which operational harm would persist without the intended correction? Half the expected capacity is unavailable and link failover is fragile. Subscribers suffer flooding or Layer 2 interruption after a supervisor failure. Customers experience extended blackholes before alternate paths take over. No adjacency forms, so link-state routes cannot traverse that link. ExplanationCorrect Answer B:Subscribers suffer flooding or Layer 2 interruption after a supervisor failure. NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. Incorrect Answers A:Half the expected capacity is unavailable and link failover is fragile. The choice would be appropriate if a bundled uplink has two configured members but only one is usable because the second member's operational parameters differ. Here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. C:Customers experience extended blackholes before alternate paths take over. It addresses a different problem: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. Here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. D:No adjacency forms, so link-state routes cannot traverse that link. This could matter when an IS-IS neighbor remains down after an interface template disables its hello transmission. In this case, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets.
Question 973In a separate fictional JNCIS-SP lab review for Eastbridge Networks 244, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. What should the Junos specialist change first to resolve this specific fault? Enable and verify supported nonstop active routing with required redundancy prerequisites. Configure and validate supported GRES readiness before an authorized controlled failover. Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. Check label advertisements for the FEC and restore a valid LDP downstream binding. ExplanationCorrect Answer C:Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. MAC tables and customer bridge forwarding remain stable during controlled switchover. NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. Incorrect Answers A:Enable and verify supported nonstop active routing with required redundancy prerequisites. This addresses a situation in which traffic briefly vanishes after a Routing Engine failure because the backup does not maintain protocol state; however, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. B:Configure and validate supported GRES readiness before an authorized controlled failover. The choice would be appropriate if a planned Routing Engine switchover resets forwarding unexpectedly because chassis graceful switchover was not prepared. Here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. D:Check label advertisements for the FEC and restore a valid LDP downstream binding. It addresses a different problem: An MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. Here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets.
Question 974In a separate fictional JNCIS-SP lab review for Eastbridge Networks 244, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. What technical principle underlies the right remedy? VRRP provides a shared virtual gateway address with an active router and standby candidates. NSR maintains routing protocol information on the backup Routing Engine beyond basic GRES forwarding preservation. Junos routing policy is evaluated by terms whose order and matching conditions affect the outcome. NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. ExplanationCorrect Answer D:NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. MAC tables and customer bridge forwarding remain stable during controlled switchover. Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. Incorrect Answers A:VRRP provides a shared virtual gateway address with an active router and standby candidates. That relates to circumstances in which an access VLAN loses default-gateway access after the primary router fails because the backup's VRRP state is incorrect. Here the problem is that a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. B:NSR maintains routing protocol information on the backup Routing Engine beyond basic GRES forwarding preservation. This addresses a situation in which traffic briefly vanishes after a Routing Engine failure because the backup does not maintain protocol state; however, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. C:Junos routing policy is evaluated by terms whose order and matching conditions affect the outcome. The choice would be appropriate if a broad accept term in a BGP policy is evaluated before a specific reject term, letting unwanted routes through. Here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets.
Question 975In a separate fictional JNCIS-SP lab review for Eastbridge Networks 244, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. Which acceptance finding demonstrates the affected service has recovered? MAC tables and customer bridge forwarding remain stable during controlled switchover. During a staged failover, probes reach the customer service within the approved recovery threshold. A controlled path failure produces the designed BFD event and route withdrawal within target bounds. Both endpoints reach the expected adjacency state and share matching area membership. ExplanationCorrect Answer A:MAC tables and customer bridge forwarding remain stable during controlled switchover. Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. Incorrect Answers B:During a staged failover, probes reach the customer service within the approved recovery threshold. That relates to circumstances in which an availability test is signed off because BFD and VRRP report healthy, but customer packets still drop during failover. Here the problem is that a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. C:A controlled path failure produces the designed BFD event and route withdrawal within target bounds. This addresses a situation in which a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow; however, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. D:Both endpoints reach the expected adjacency state and share matching area membership. The choice would be appropriate if two provider routers on a point-to-point circuit cannot form an OSPF adjacency because their interfaces use different area IDs. Here, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets.
Question 976In a separate fictional JNCIS-SP lab review for Eastbridge Networks 244, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. What is the direct residual network risk if the fault remains unresolved? A supervisor failure forces routing protocol reconvergence and drops customer traffic. Subscribers suffer flooding or Layer 2 interruption after a supervisor failure. A single member fault causes a complete customer circuit outage. MPLS traffic remains broken despite restored IGP neighbors. ExplanationCorrect Answer B:Subscribers suffer flooding or Layer 2 interruption after a supervisor failure. Verify nonstop bridging and platform-specific switchover readiness for the intended bridge domains. NSB is intended to maintain relevant Layer 2 control-plane continuity through supported failover. Incorrect Answers A:A supervisor failure forces routing protocol reconvergence and drops customer traffic. This relates to a case where traffic briefly vanishes after a Routing Engine failure because the backup does not maintain protocol state; the current situation is that a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. C:A single member fault causes a complete customer circuit outage. That relates to circumstances in which a provider assumes a two-member LAG is redundant but has never checked forwarding when one member fails. Here the problem is that a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. D:MPLS traffic remains broken despite restored IGP neighbors. This addresses a situation in which after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device; however, a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets.
Question 977At fictional Orchard Link 245, a regional service-provider network, during a preproduction design validation, operations observes: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. Which targeted remediation best fits the reported behavior? Enable and verify supported nonstop active routing with required redundancy prerequisites. Measure end-to-end service continuity while exercising the planned HA transition and inspect forwarding state. Restore the documented protection features and run controlled BPDU and failover tests. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. ExplanationCorrect Answer D:Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. A controlled path failure produces the designed BFD event and route withdrawal within target bounds. Incorrect Answers A:Enable and verify supported nonstop active routing with required redundancy prerequisites. This could help if traffic briefly vanishes after a Routing Engine failure because the backup does not maintain protocol state, but not when a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. B:Measure end-to-end service continuity while exercising the planned HA transition and inspect forwarding state. This relates to a case where an availability test is signed off because BFD and VRRP report healthy, but customer packets still drop during failover; the current situation is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. C:Restore the documented protection features and run controlled BPDU and failover tests. It is useful for situations where a configuration change enables a customer loop-prevention override that also disables root and BPDU safeguards; the reported fault, though, is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.
Question 978At fictional Orchard Link 245, a regional service-provider network, during a preproduction design validation, operations observes: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. Why is this particular correction the best fit for the stated defect? High availability must be evaluated by usable service forwarding as well as control-plane states. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Graceful Routing Engine switchover seeks to preserve forwarding state across a Routing Engine change. MSTP topology calculations depend on compatible region identity and instance membership. ExplanationCorrect Answer B:BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. A controlled path failure produces the designed BFD event and route withdrawal within target bounds. Incorrect Answers A:High availability must be evaluated by usable service forwarding as well as control-plane states. It is relevant if an availability test is signed off because BFD and VRRP report healthy, but customer packets still drop during failover, but the reported issue is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. C:Graceful Routing Engine switchover seeks to preserve forwarding state across a Routing Engine change. This relates to a case where a planned Routing Engine switchover resets forwarding unexpectedly because chassis graceful switchover was not prepared; the current situation is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. D:MSTP topology calculations depend on compatible region identity and instance membership. It is useful for situations where two interconnected switches place the same VLAN in different MSTP instances, leading to inconsistent blocking behavior; the reported fault, though, is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.
Question 979At fictional Orchard Link 245, a regional service-provider network, during a preproduction design validation, operations observes: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. What direct observation would prove the corrective action worked? During a staged failover, probes reach the customer service within the approved recovery threshold. Both intended links join the bundle and sample traffic uses approved members. Neighbors reach Full and relevant LSA identifiers and sequence states agree. A controlled path failure produces the designed BFD event and route withdrawal within target bounds. ExplanationCorrect Answer D:A controlled path failure produces the designed BFD event and route withdrawal within target bounds. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. Incorrect Answers A:During a staged failover, probes reach the customer service within the approved recovery threshold. This is applicable when an availability test is signed off because BFD and VRRP report healthy, but customer packets still drop during failover; the present condition is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. B:Both intended links join the bundle and sample traffic uses approved members. It is relevant if a bundled uplink has two configured members but only one is usable because the second member's operational parameters differ, but the reported issue is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. C:Neighbors reach Full and relevant LSA identifiers and sequence states agree. This could help if two supposed adjacent routers have different views of a backbone link because database synchronization never completes, but not when a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.
Question 980At fictional Orchard Link 245, a regional service-provider network, during a preproduction design validation, operations observes: A core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. Which failure consequence follows most closely from ignoring this issue? Maintenance triggers avoidable traffic loss and prolonged recovery. Customers experience extended blackholes before alternate paths take over. Traffic is blackholed because neighbors keep invalid routes or fail to assist recovery. Duplicate identity creates conflicting LSPs and unstable route computation. ExplanationCorrect Answer B:Customers experience extended blackholes before alternate paths take over. BFD can detect forwarding-path failure more promptly than many ordinary routing protocol timers. Configure supported BFD monitoring with the neighbor protocol and validate failure detection behavior. Incorrect Answers A:Maintenance triggers avoidable traffic loss and prolonged recovery. That could help when a planned Routing Engine switchover resets forwarding unexpectedly because chassis graceful switchover was not prepared; here, a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. C:Traffic is blackholed because neighbors keep invalid routes or fail to assist recovery. It is relevant if a provider assumes graceful restart will work during a routing process restart without considering neighbor support, but the reported issue is that a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow. D:Duplicate identity creates conflicting LSPs and unstable route computation. This could help if a device cloned from a lab template has the same IS-IS system ID as a production router, but not when a core route remains active long after a forwarding path fails because the routing protocol's regular timeout is too slow.