Question 790In a separate fictional JNCIS-SP lab review for Stonefield Telecom 198, a carrier-edge and core routing team, following a monitored network change window, engineers find: After an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. Which networking principle explains why the proposed correction is appropriate? MPLS transport cutovers need working end-to-end label forwarding, not just successful configuration commits. Protocol adjacency health does not prove every required MPLS forwarding entry exists. Aggregate route eligibility depends on the presence of suitable contributing routes and policy conditions. MPLS label forwarding must follow the current resolved transport topology. ExplanationCorrect Answer D:MPLS label forwarding must follow the current resolved transport topology. The active label operation now uses the recovered egress next hop. Verify renewed label forwarding entries after the IGP path change and correct stale state. Incorrect Answers A:MPLS transport cutovers need working end-to-end label forwarding, not just successful configuration commits. It addresses a different problem: A new MPLS LSP is provisioned and traffic is moved before its end-to-end reachability has been tested. Here, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. B:Protocol adjacency health does not prove every required MPLS forwarding entry exists. This could matter when monitoring checks only LDP adjacency state and never detects missing forwarding labels for a critical PE loopback. In this case, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. C:Aggregate route eligibility depends on the presence of suitable contributing routes and policy conditions. That could help when a summary prefix is advertised even though operators have not confirmed which customer specifics contribute to it; here, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device.
Question 791In a separate fictional JNCIS-SP lab review for Stonefield Telecom 198, a carrier-edge and core routing team, following a monitored network change window, engineers find: After an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. Which validation result would confirm the design is now functioning? The active label operation now uses the recovered egress next hop. The target loopback FEC has a valid binding and corresponding programmed label action. The penultimate and egress forwarding entries match the intended label disposition. A controlled excess-route test triggers the intended protective response and logging. ExplanationCorrect Answer A:The active label operation now uses the recovered egress next hop. Verify renewed label forwarding entries after the IGP path change and correct stale state. MPLS label forwarding must follow the current resolved transport topology. Incorrect Answers B:The target loopback FEC has a valid binding and corresponding programmed label action. It addresses a different problem: Monitoring checks only LDP adjacency state and never detects missing forwarding labels for a critical PE loopback. Here, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. C:The penultimate and egress forwarding entries match the intended label disposition. This could matter when an operator sees the transport label removed near the egress and flags a failure despite the design allowing PHP. In this case, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. D:A controlled excess-route test triggers the intended protective response and logging. That could help when a misconfigured customer sends thousands of unintended routes and overwhelms the expected BGP peering scale; here, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device.
Question 792In a separate fictional JNCIS-SP lab review for Stonefield Telecom 198, a carrier-edge and core routing team, following a monitored network change window, engineers find: After an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. What likely service impact does this condition create? Customers experience a blackhole hidden by otherwise present route advertisements. MPLS traffic remains broken despite restored IGP neighbors. An SID collision or wrong label steers packets onto an unintended destination. IPv6 service fails across a still-configured but unusable tunnel. ExplanationCorrect Answer B:MPLS traffic remains broken despite restored IGP neighbors. Verify renewed label forwarding entries after the IGP path change and correct stale state. MPLS label forwarding must follow the current resolved transport topology. Incorrect Answers A:Customers experience a blackhole hidden by otherwise present route advertisements. The choice would be appropriate if a service path references an LSP that is down, but its IP route remains visible in the route table. Here, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. C:An SID collision or wrong label steers packets onto an unintended destination. It addresses a different problem: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. Here, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. D:IPv6 service fails across a still-configured but unusable tunnel. This could matter when an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. In this case, after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device.
Question 793At fictional Clearwater Peering 199, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. Which configuration or operational correction most directly addresses this failure? Correct the SID assignment and confirm the intended segment path resolves to that node. Check LDP transport address reachability and session parameters through the IGP. Inspect label stack, bottom-of-stack indicator, and the expected transport operation. Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. ExplanationCorrect Answer A:Correct the SID assignment and confirm the intended segment path resolves to that node. Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. The target prefix SID resolves to the planned node and the corresponding SR LSP is active. Incorrect Answers B:Check LDP transport address reachability and session parameters through the IGP. The choice would be appropriate if two core routers cannot form an LDP session even though they discover one another on the connected link. Here, a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. C:Inspect label stack, bottom-of-stack indicator, and the expected transport operation. That option concerns operations assumes a packet is plain IP because the capture display does not decode its MPLS shim header. The problem here is different: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. D:Review bridge-domain membership, MAC learning and aging behavior and correct the affected interface configuration. It addresses a different problem: An edge switch floods ordinary known unicast frames because it never learns the destination MAC on the expected port. Here, a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation.
Question 794At fictional Clearwater Peering 199, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. Which Junos forwarding or control-plane rule applies to this case? MPLS TTL handling can affect the hop visibility of path diagnostics. Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. MPLS transit forwarding depends on installed label operations at each participating node. A BGP path cannot be installed for forwarding when its next hop cannot be resolved. ExplanationCorrect Answer B:Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. Correct the SID assignment and confirm the intended segment path resolves to that node. The target prefix SID resolves to the planned node and the corresponding SR LSP is active. Incorrect Answers A:MPLS TTL handling can affect the hop visibility of path diagnostics. That relates to circumstances in which traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. Here the problem is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. C:MPLS transit forwarding depends on installed label operations at each participating node. The choice would be appropriate if an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing. Here, a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. D:A BGP path cannot be installed for forwarding when its next hop cannot be resolved. That option concerns an IBGP-learned external prefix is present but inactive because the advertised next-hop address has no IGP reachability. The problem here is different: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation.
Question 795At fictional Clearwater Peering 199, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. What operational evidence best establishes successful remediation? The target prefix SID resolves to the planned node and the corresponding SR LSP is active. An MPLS-aware trace and service probe pass before and after the selected cutover. The penultimate and egress forwarding entries match the intended label disposition. A correctly sized customer frame traverses the entire provider handoff without drops. ExplanationCorrect Answer A:The target prefix SID resolves to the planned node and the corresponding SR LSP is active. Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. Correct the SID assignment and confirm the intended segment path resolves to that node. Incorrect Answers B:An MPLS-aware trace and service probe pass before and after the selected cutover. That relates to circumstances in which a new MPLS LSP is provisioned and traffic is moved before its end-to-end reachability has been tested. Here the problem is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. C:The penultimate and egress forwarding entries match the intended label disposition. This addresses a situation in which an operator sees the transport label removed near the egress and flags a failure despite the design allowing PHP; however, a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. D:A correctly sized customer frame traverses the entire provider handoff without drops. The choice would be appropriate if a service-provider QinQ link carries small frames but drops customer frames when the extra VLAN header exceeds the link MTU. Here, a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation.
Question 796At fictional Clearwater Peering 199, a regional service-provider network, during a subscriber traffic restoration exercise, operations observes: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. Which operational harm would persist without the intended correction? Labeled packets are discarded at the affected core node. MPLS traffic remains broken despite restored IGP neighbors. Subscribers suffer flooding or Layer 2 interruption after a supervisor failure. An SID collision or wrong label steers packets onto an unintended destination. ExplanationCorrect Answer D:An SID collision or wrong label steers packets onto an unintended destination. Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. Correct the SID assignment and confirm the intended segment path resolves to that node. Incorrect Answers A:Labeled packets are discarded at the affected core node. This relates to a case where an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing; the current situation is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. B:MPLS traffic remains broken despite restored IGP neighbors. It is useful for situations where after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device; the reported fault, though, is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. C:Subscribers suffer flooding or Layer 2 interruption after a supervisor failure. That relates to circumstances in which a switch with redundant Routing Engines loses Layer 2 MAC learning state during switchover despite planned availability targets. Here the problem is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation.
Question 797In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 200, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. What should the Junos specialist change first to resolve this specific fault? Correct the SID assignment and confirm the intended segment path resolves to that node. Check LDP transport address reachability and session parameters through the IGP. Review RSVP path constraints and explicit-route settings, then reestablish the LSP. Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. ExplanationCorrect Answer A:Correct the SID assignment and confirm the intended segment path resolves to that node. The target prefix SID resolves to the planned node and the corresponding SR LSP is active. Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. Incorrect Answers B:Check LDP transport address reachability and session parameters through the IGP. This relates to a case where two core routers cannot form an LDP session even though they discover one another on the connected link; the current situation is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. C:Review RSVP path constraints and explicit-route settings, then reestablish the LSP. It is useful for situations where an RSVP-signaled LSP follows a congested transit hop instead of the approved engineered route; the reported fault, though, is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. D:Repair IPv4 underlay reachability to the tunnel endpoint before modifying IPv6 customer prefixes. That relates to circumstances in which an IPv6 service is carried through an IPv4 underlay, but the tunnel endpoint's IPv4 route has disappeared. Here the problem is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation.
Question 798In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 200, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. What technical principle underlies the right remedy? Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. A route's presence is insufficient if its selected MPLS transport next hop is unusable. Penultimate-hop popping can remove the outer transport label before the final LSR. BGP import policy governs which learned prefixes enter local route selection. ExplanationCorrect Answer A:Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. The target prefix SID resolves to the planned node and the corresponding SR LSP is active. Correct the SID assignment and confirm the intended segment path resolves to that node. Incorrect Answers B:A route's presence is insufficient if its selected MPLS transport next hop is unusable. This could help if a service path references an LSP that is down, but its IP route remains visible in the route table, but not when a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. C:Penultimate-hop popping can remove the outer transport label before the final LSR. This relates to a case where an operator sees the transport label removed near the egress and flags a failure despite the design allowing PHP; the current situation is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. D:BGP import policy governs which learned prefixes enter local route selection. It is useful for situations where a provider receives a customer-only prefix from a transit peer that should be blocked by an import policy; the reported fault, though, is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation.
Question 799In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 200, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. Which acceptance finding demonstrates the affected service has recovered? The target prefix SID resolves to the planned node and the corresponding SR LSP is active. The route resolves through an operational LSP and test traffic reaches the remote endpoint. The failing RSVP hop is identified and the LSP reports Up after correction. The route detail identifies the intended contributing prefixes and the summary is active only in the planned circumstances. ExplanationCorrect Answer A:The target prefix SID resolves to the planned node and the corresponding SR LSP is active. Correct the SID assignment and confirm the intended segment path resolves to that node. Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. Incorrect Answers B:The route resolves through an operational LSP and test traffic reaches the remote endpoint. It is relevant if a service path references an LSP that is down, but its IP route remains visible in the route table, but the reported issue is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. C:The failing RSVP hop is identified and the LSP reports Up after correction. This could help if an RSVP LSP stays down but engineers only examine the ingress router's IP default route, but not when a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. D:The route detail identifies the intended contributing prefixes and the summary is active only in the planned circumstances. This relates to a case where a summary prefix is advertised even though operators have not confirmed which customer specifics contribute to it; the current situation is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation.
Question 800In a separate fictional JNCIS-SP lab review for Glenwood Connectivity 200, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: A provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. What is the direct residual network risk if the fault remains unresolved? An SID collision or wrong label steers packets onto an unintended destination. Transport LSPs are absent despite healthy basic IP routing. A correct label stack is broken by applying the wrong role assumption. Customers still experience blackholes despite apparently healthy protocol neighbors. ExplanationCorrect Answer A:An SID collision or wrong label steers packets onto an unintended destination. Correct the SID assignment and confirm the intended segment path resolves to that node. Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. Incorrect Answers B:Transport LSPs are absent despite healthy basic IP routing. This is applicable when two core routers cannot form an LDP session even though they discover one another on the connected link; the present condition is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. C:A correct label stack is broken by applying the wrong role assumption. It is relevant if a network test expects the ingress PE to swap a label that it should actually impose, but the reported issue is that a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. D:Customers still experience blackholes despite apparently healthy protocol neighbors. This could help if an engineer sees an OSPF route in the routing table and closes the incident without testing the egress path, but not when a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation.