Question 770At fictional Brightstone Backbone 193, a regional service-provider network, during a two-site transit migration, operations observes: A tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. Why is this particular correction the best fit for the stated defect? A prefix SID normally expresses reachability to a node or prefix along the underlying shortest path. LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. MPLS transit forwarding depends on installed label operations at each participating node. RSTP edge-port behavior is intended for ports without downstream bridge participation. ExplanationCorrect Answer B:LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. Align route resolution and LSP preference with the documented transport service intent. The selected service resolves over the intended RSVP LSP and follows engineered hops. Incorrect Answers A:A prefix SID normally expresses reachability to a node or prefix along the underlying shortest path. That relates to circumstances in which a team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path. Here the problem is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. C:MPLS transit forwarding depends on installed label operations at each participating node. The choice would be appropriate if an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing. Here, a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. D:RSTP edge-port behavior is intended for ports without downstream bridge participation. That option concerns a switch port connecting another bridge is incorrectly marked as an edge port, weakening normal loop-avoidance behavior. The problem here is different: A tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change.
Question 771At fictional Brightstone Backbone 193, a regional service-provider network, during a two-site transit migration, operations observes: A tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. What direct observation would prove the corrective action worked? The failing RSVP hop is identified and the LSP reports Up after correction. Forwarding tables and controlled trace results agree with documented TTL behavior. The selected service resolves over the intended RSVP LSP and follows engineered hops. The authorized IPv6 prefixes arrive in the intended inet6 table without IPv4 policy changes. ExplanationCorrect Answer C:The selected service resolves over the intended RSVP LSP and follows engineered hops. LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. Align route resolution and LSP preference with the documented transport service intent. Incorrect Answers A:The failing RSVP hop is identified and the LSP reports Up after correction. It is useful for situations where an RSVP LSP stays down but engineers only examine the ingress router's IP default route; the reported fault, though, is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. B:Forwarding tables and controlled trace results agree with documented TTL behavior. That relates to circumstances in which traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. Here the problem is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. D:The authorized IPv6 prefixes arrive in the intended inet6 table without IPv4 policy changes. The choice would be appropriate if an established BGP peer exchanges IPv4 but rejects all authorized IPv6 prefixes due to a misplaced family-specific filter. Here, a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change.
Question 772At fictional Brightstone Backbone 193, a regional service-provider network, during a two-site transit migration, operations observes: A tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. Which failure consequence follows most closely from ignoring this issue? MPLS traffic remains broken despite restored IGP neighbors. A correct label stack is broken by applying the wrong role assumption. Large customer frames fail selectively and create difficult-to-reproduce application problems. Traffic bypasses an approved low-latency or protected path. ExplanationCorrect Answer D:Traffic bypasses an approved low-latency or protected path. LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. Align route resolution and LSP preference with the documented transport service intent. Incorrect Answers A:MPLS traffic remains broken despite restored IGP neighbors. This relates to a case where after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device; the current situation is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. B:A correct label stack is broken by applying the wrong role assumption. It is useful for situations where a network test expects the ingress PE to swap a label that it should actually impose; the reported fault, though, is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. C:Large customer frames fail selectively and create difficult-to-reproduce application problems. That relates to circumstances in which a service-provider QinQ link carries small frames but drops customer frames when the extra VLAN header exceeds the link MTU. Here the problem is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change.
Question 773In a separate fictional JNCIS-SP lab review for Eastbridge Networks 194, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. What intervention most directly restores the intended routing or switching behavior? Check label advertisements for the FEC and restore a valid LDP downstream binding. Correct the SID assignment and confirm the intended segment path resolves to that node. Configure supported loop protection where appropriate and test loss-of-BPDU behavior. Align route resolution and LSP preference with the documented transport service intent. ExplanationCorrect Answer D:Align route resolution and LSP preference with the documented transport service intent. The selected service resolves over the intended RSVP LSP and follows engineered hops. LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. Incorrect Answers A:Check label advertisements for the FEC and restore a valid LDP downstream binding. This could help if an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop, but not when a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. B:Correct the SID assignment and confirm the intended segment path resolves to that node. This relates to a case where a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation; the current situation is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. C:Configure supported loop protection where appropriate and test loss-of-BPDU behavior. It is useful for situations where a blocked redundant link unexpectedly starts forwarding when BPDUs cease on a faulty remote bridge; the reported fault, though, is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change.
Question 774In a separate fictional JNCIS-SP lab review for Eastbridge Networks 194, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. Which networking principle explains why the proposed correction is appropriate? MPLS ingress typically pushes a label, transit nodes swap, and egress behavior may remove it. Penultimate-hop popping can remove the outer transport label before the final LSR. LAG availability depends on traffic being redirected to healthy active members after failure. LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. ExplanationCorrect Answer D:LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. The selected service resolves over the intended RSVP LSP and follows engineered hops. Align route resolution and LSP preference with the documented transport service intent. Incorrect Answers A:MPLS ingress typically pushes a label, transit nodes swap, and egress behavior may remove it. It is relevant if a network test expects the ingress PE to swap a label that it should actually impose, but the reported issue is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. B:Penultimate-hop popping can remove the outer transport label before the final LSR. This could help if an operator sees the transport label removed near the egress and flags a failure despite the design allowing PHP, but not when a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. C:LAG availability depends on traffic being redirected to healthy active members after failure. This relates to a case where a provider assumes a two-member LAG is redundant but has never checked forwarding when one member fails; the current situation is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change.
Question 775In a separate fictional JNCIS-SP lab review for Eastbridge Networks 194, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. Which validation result would confirm the design is now functioning? The target prefix SID resolves to the planned node and the corresponding SR LSP is active. The active label operation now uses the recovered egress next hop. OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. The selected service resolves over the intended RSVP LSP and follows engineered hops. ExplanationCorrect Answer D:The selected service resolves over the intended RSVP LSP and follows engineered hops. Align route resolution and LSP preference with the documented transport service intent. LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. Incorrect Answers A:The target prefix SID resolves to the planned node and the corresponding SR LSP is active. This is applicable when a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation; the present condition is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. B:The active label operation now uses the recovered egress next hop. It is relevant if after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device, but the reported issue is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. C:OSPFv3 neighbors are established and the remote inet6 table contains the expected prefix. This could help if an IPv6 prefix is missing across a point-to-point link because OSPFv2 was configured but OSPFv3 was omitted, but not when a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change.
Question 776In a separate fictional JNCIS-SP lab review for Eastbridge Networks 194, a carrier-edge and core routing team, following a backbone resilience drill, engineers find: A tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. What likely service impact does this condition create? The engineered service remains unavailable or overcommits transit capacity. Labeled packets are discarded at the affected core node. Customers can inject unapproved Layer 2 traffic into the provider bridge. Traffic bypasses an approved low-latency or protected path. ExplanationCorrect Answer D:Traffic bypasses an approved low-latency or protected path. Align route resolution and LSP preference with the documented transport service intent. LDP distributes reachability labels while RSVP-TE can enforce explicit traffic-engineering paths. Incorrect Answers A:The engineered service remains unavailable or overcommits transit capacity. That could help when an RSVP LSP setup fails after requested bandwidth exceeds available reservable capacity on a transit link; here, a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. B:Labeled packets are discarded at the affected core node. This is applicable when an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing; the present condition is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. C:Customers can inject unapproved Layer 2 traffic into the provider bridge. It is relevant if an interface permits every customer VLAN tag despite a contract listing only two approved VLANs, but the reported issue is that a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change.
Question 777At fictional Orchard Link 195, a regional service-provider network, during a preproduction design validation, operations observes: Traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. Which configuration or operational correction most directly addresses this failure? Perform controlled LSP validation and only then switch the authorized service resolution. Correct the SID assignment and confirm the intended segment path resolves to that node. Interpret MPLS TTL and traceroute behavior using the configured transport model. Set deliberate interface priorities and confirm the DR and BDR roles after a controlled election. ExplanationCorrect Answer C:Interpret MPLS TTL and traceroute behavior using the configured transport model. MPLS TTL handling can affect the hop visibility of path diagnostics. Forwarding tables and controlled trace results agree with documented TTL behavior. Incorrect Answers A:Perform controlled LSP validation and only then switch the authorized service resolution. This could matter when a new MPLS LSP is provisioned and traffic is moved before its end-to-end reachability has been tested. In this case, traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. B:Correct the SID assignment and confirm the intended segment path resolves to that node. That could help when a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation; here, traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. D:Set deliberate interface priorities and confirm the DR and BDR roles after a controlled election. It is relevant if an unplanned access router becomes designated router after its interface receives an unexpectedly high priority, but the reported issue is that traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut.
Question 778At fictional Orchard Link 195, a regional service-provider network, during a preproduction design validation, operations observes: Traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. Which Junos forwarding or control-plane rule applies to this case? Protocol adjacency health does not prove every required MPLS forwarding entry exists. RSVP-TE bandwidth admission constrains whether an LSP can reserve the requested resources. MPLS TTL handling can affect the hop visibility of path diagnostics. IS-IS routers need consistent flooded LSP information for reliable SPF results. ExplanationCorrect Answer C:MPLS TTL handling can affect the hop visibility of path diagnostics. Interpret MPLS TTL and traceroute behavior using the configured transport model. Forwarding tables and controlled trace results agree with documented TTL behavior. Incorrect Answers A:Protocol adjacency health does not prove every required MPLS forwarding entry exists. It addresses a different problem: Monitoring checks only LDP adjacency state and never detects missing forwarding labels for a critical PE loopback. Here, traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. B:RSVP-TE bandwidth admission constrains whether an LSP can reserve the requested resources. This could matter when an RSVP LSP setup fails after requested bandwidth exceeds available reservable capacity on a transit link. In this case, traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. D:IS-IS routers need consistent flooded LSP information for reliable SPF results. This is applicable when a remote PE misses a new loopback route because IS-IS link-state flooding is incomplete after an adjacency reset; the present condition is that traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut.
Question 779At fictional Orchard Link 195, a regional service-provider network, during a preproduction design validation, operations observes: Traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. What operational evidence best establishes successful remediation? Packet capture and forwarding state show the intended outgoing transport label. A controlled packet trace follows the intended segment program under the chosen IGP topology. The authorized inet6 routes are accepted while prohibited IPv6 prefixes remain blocked. Forwarding tables and controlled trace results agree with documented TTL behavior. ExplanationCorrect Answer D:Forwarding tables and controlled trace results agree with documented TTL behavior. MPLS TTL handling can affect the hop visibility of path diagnostics. Interpret MPLS TTL and traceroute behavior using the configured transport model. Incorrect Answers A:Packet capture and forwarding state show the intended outgoing transport label. That option concerns operations assumes a packet is plain IP because the capture display does not decode its MPLS shim header. The problem here is different: Traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. B:A controlled packet trace follows the intended segment program under the chosen IGP topology. It addresses a different problem: A team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path. Here, traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. C:The authorized inet6 routes are accepted while prohibited IPv6 prefixes remain blocked. This could matter when a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. In this case, traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut.
Question 780At fictional Orchard Link 195, a regional service-provider network, during a preproduction design validation, operations observes: Traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. Which operational harm would persist without the intended correction? Healthy MPLS transport is disrupted by a false fault diagnosis. Transport LSPs are absent despite healthy basic IP routing. An incorrect topology conclusion prompts needless routing changes. Unnecessary route changes mask a switching defect and prolong the outage. ExplanationCorrect Answer C:An incorrect topology conclusion prompts needless routing changes. MPLS TTL handling can affect the hop visibility of path diagnostics. Interpret MPLS TTL and traceroute behavior using the configured transport model. Incorrect Answers A:Healthy MPLS transport is disrupted by a false fault diagnosis. The choice would be appropriate if an operator sees the transport label removed near the egress and flags a failure despite the design allowing PHP. Here, traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. B:Transport LSPs are absent despite healthy basic IP routing. That option concerns two core routers cannot form an LDP session even though they discover one another on the connected link. The problem here is different: Traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. D:Unnecessary route changes mask a switching defect and prolong the outage. This could matter when an operator adds an IP route to fix traffic that never leaves a local bridge domain because its destination MAC is unknown. In this case, traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut.