McAfee Secured

Exam Code: JN0-364

Exam Name: Service Provider Routing and Switching, Specialist (JNCIS-SP)

Certification Provider: Juniper

100% Juniper JN0-364 Guaranteed Success With Testking Training Materials

Get Real JN0-364 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

69 Questions & Answers with Testing Engine

"Service Provider Routing and Switching, Specialist (JNCIS-SP) Exam", also known as JN0-364 exam, is a Juniper certification exam.

Pass your tests with the always up-to-date JN0-364 Exam Engine. Your JN0-364 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Juniper JN0-364 Practice Test 15

Question 140

At fictional Fairhaven Broadband 035, a regional service-provider network, during a preproduction design validation, operations observes: Two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. Which operational harm would persist without the intended correction?

  1. Duplicate identity produces unstable topology and confusing route calculations.
  2. Sites in different areas cannot exchange business traffic reliably.
  3. The IGP cannot distribute transit reachability over the circuit.
  4. Repeated flooding and customer frame loss continue despite healthy routes.

Explanation

Correct Answer

A:

Duplicate identity produces unstable topology and confusing route calculations. The OSPF router ID uniquely identifies a router in link-state advertisements. Assign unique stable router IDs and safely reestablish affected OSPF adjacencies.

Incorrect Answers

B:

Sites in different areas cannot exchange business traffic reliably. This is applicable when a site advertises internal prefixes inside one area, but a remote OSPF area cannot learn them because the area border configuration is incomplete; the present condition is that two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

C:

The IGP cannot distribute transit reachability over the circuit. It is relevant if two provider routers on a point-to-point circuit cannot form an OSPF adjacency because their interfaces use different area IDs, but the reported issue is that two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

D:

Repeated flooding and customer frame loss continue despite healthy routes. This could help if a MAC moves rapidly among provider ports after a cabling change, yet troubleshooting focuses only on IP routing tables, but not when two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

Question 141

In a separate fictional JNCIS-SP lab review for Cedarwater Transit 036, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: Two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. What should the Junos specialist change first to resolve this specific fault?

  1. Review planned OSPF costs in both directions and correct the traffic-engineering values.
  2. Assign unique stable router IDs and safely reestablish affected OSPF adjacencies.
  3. Inspect database-exchange state and repair the adjacency rather than editing unrelated route preferences.
  4. Check transit MPLS forwarding state and repair the missing label operation.

Explanation

Correct Answer

B:

Assign unique stable router IDs and safely reestablish affected OSPF adjacencies. Each device shows a distinct router ID and neighbors exchange consistent LSDB entries. The OSPF router ID uniquely identifies a router in link-state advertisements.

Incorrect Answers

A:

Review planned OSPF costs in both directions and correct the traffic-engineering values. This could matter when provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. In this case, two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

C:

Inspect database-exchange state and repair the adjacency rather than editing unrelated route preferences. This is applicable when two supposed adjacent routers have different views of a backbone link because database synchronization never completes; the present condition is that two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

D:

Check transit MPLS forwarding state and repair the missing label operation. It is relevant if an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing, but the reported issue is that two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

Question 142

In a separate fictional JNCIS-SP lab review for Cedarwater Transit 036, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: Two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. What technical principle underlies the right remedy?

  1. A passive interface can advertise connected reachability without sending OSPF hellos to customers.
  2. OSPF SPF computes least-cost paths using the advertised topology metrics.
  3. The OSPF router ID uniquely identifies a router in link-state advertisements.
  4. IBGP connects peers within an AS while EBGP represents inter-AS exchange with different policy expectations.

Explanation

Correct Answer

C:

The OSPF router ID uniquely identifies a router in link-state advertisements. Each device shows a distinct router ID and neighbors exchange consistent LSDB entries. Assign unique stable router IDs and safely reestablish affected OSPF adjacencies.

Incorrect Answers

A:

A passive interface can advertise connected reachability without sending OSPF hellos to customers. It addresses a different problem: A provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only. Here, two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

B:

OSPF SPF computes least-cost paths using the advertised topology metrics. This could matter when provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. In this case, two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

D:

IBGP connects peers within an AS while EBGP represents inter-AS exchange with different policy expectations. This is applicable when an operator configures an internal route-reflector session as EBGP and introduces an unintended AS boundary; the present condition is that two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

Question 143

In a separate fictional JNCIS-SP lab review for Cedarwater Transit 036, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: Two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. Which acceptance finding demonstrates the affected service has recovered?

  1. The circuit forms the expected point-to-point adjacency without an unwanted DR election.
  2. Each device shows a distinct router ID and neighbors exchange consistent LSDB entries.
  3. The approved prefix is present as an external OSPF route and unauthorized prefixes remain absent.
  4. Representative large overlay packets cross the complete GRE path without loss.

Explanation

Correct Answer

B:

Each device shows a distinct router ID and neighbors exchange consistent LSDB entries. Assign unique stable router IDs and safely reestablish affected OSPF adjacencies. The OSPF router ID uniquely identifies a router in link-state advertisements.

Incorrect Answers

A:

The circuit forms the expected point-to-point adjacency without an unwanted DR election. That option concerns OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology. The problem here is different: Two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

C:

The approved prefix is present as an external OSPF route and unauthorized prefixes remain absent. This could matter when a static service prefix is missing from OSPF because the export policy was attached but does not match it. In this case, two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

D:

Representative large overlay packets cross the complete GRE path without loss. That could help when large packets fail on an overlay while small probes work because encapsulation overhead exceeds path MTU; here, two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

Question 144

In a separate fictional JNCIS-SP lab review for Cedarwater Transit 036, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: Two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template. What is the direct residual network risk if the fault remains unresolved?

  1. The IGP cannot distribute transit reachability over the circuit.
  2. Duplicate identity produces unstable topology and confusing route calculations.
  3. Routing connectivity fails or a poorly scoped workaround weakens control-plane trust.
  4. IPv6 traffic is entirely lost due to an unsuitable policy match.

Explanation

Correct Answer

B:

Duplicate identity produces unstable topology and confusing route calculations. Assign unique stable router IDs and safely reestablish affected OSPF adjacencies. The OSPF router ID uniquely identifies a router in link-state advertisements.

Incorrect Answers

A:

The IGP cannot distribute transit reachability over the circuit. The choice would be appropriate if two provider routers on a point-to-point circuit cannot form an OSPF adjacency because their interfaces use different area IDs. Here, two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

C:

Routing connectivity fails or a poorly scoped workaround weakens control-plane trust. It addresses a different problem: A newly hardened OSPF transit link stops exchanging neighbors because its authentication parameters do not agree. Here, two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

D:

IPv6 traffic is entirely lost due to an unsuitable policy match. This could matter when a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish. In this case, two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template.

Question 145

At fictional Riverstone Networks 037, a regional service-provider network, during a core-routing acceptance test, operations observes: On a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure. Which targeted remediation best fits the reported behavior?

  1. Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes.
  2. Confirm the DR and BDR election and distinguish the required adjacency state for each neighbor relationship.
  3. Fix the OSPF export policy's precise match and validate external route origination.
  4. Enable and verify supported nonstop active routing with required redundancy prerequisites.

Explanation

Correct Answer

B:

Confirm the DR and BDR election and distinguish the required adjacency state for each neighbor relationship. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. Expected DR and BDR peers are Full while the relevant non-DR relationship can legitimately remain 2-Way.

Incorrect Answers

A:

Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. This addresses a situation in which an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets; however, on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

C:

Fix the OSPF export policy's precise match and validate external route origination. That option concerns a static service prefix is missing from OSPF because the export policy was attached but does not match it. The problem here is different: On a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

D:

Enable and verify supported nonstop active routing with required redundancy prerequisites. It addresses a different problem: Traffic briefly vanishes after a Routing Engine failure because the backup does not maintain protocol state. Here, on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

Question 146

At fictional Riverstone Networks 037, a regional service-provider network, during a core-routing acceptance test, operations observes: On a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure. Why is this particular correction the best fit for the stated defect?

  1. A calculated OSPF path is not a substitute for functional packet forwarding validation.
  2. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other.
  3. OSPF shortest-path calculations rely on consistent synchronized link-state information within an area.
  4. Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery.

Explanation

Correct Answer

B:

On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. Confirm the DR and BDR election and distinguish the required adjacency state for each neighbor relationship. Expected DR and BDR peers are Full while the relevant non-DR relationship can legitimately remain 2-Way.

Incorrect Answers

A:

A calculated OSPF path is not a substitute for functional packet forwarding validation. That relates to circumstances in which an engineer sees an OSPF route in the routing table and closes the incident without testing the egress path. Here the problem is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

C:

OSPF shortest-path calculations rely on consistent synchronized link-state information within an area. The choice would be appropriate if two supposed adjacent routers have different views of a backbone link because database synchronization never completes. Here, on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

D:

Graceful restart relies on appropriate protocol and neighbor support to retain forwarding through control-plane recovery. That option concerns a provider assumes graceful restart will work during a routing process restart without considering neighbor support. The problem here is different: On a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

Question 147

At fictional Riverstone Networks 037, a regional service-provider network, during a core-routing acceptance test, operations observes: On a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure. What direct observation would prove the corrective action worked?

  1. Customer subnet is visible in the IGP but no neighbor session forms on the LAN.
  2. Route detail and controlled traffic testing select the documented primary path.
  3. The target prefix SID resolves to the planned node and the corresponding SR LSP is active.
  4. Expected DR and BDR peers are Full while the relevant non-DR relationship can legitimately remain 2-Way.

Explanation

Correct Answer

D:

Expected DR and BDR peers are Full while the relevant non-DR relationship can legitimately remain 2-Way. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. Confirm the DR and BDR election and distinguish the required adjacency state for each neighbor relationship.

Incorrect Answers

A:

Customer subnet is visible in the IGP but no neighbor session forms on the LAN. It is useful for situations where a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only; the reported fault, though, is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

B:

Route detail and controlled traffic testing select the documented primary path. That relates to circumstances in which provider traffic takes a long backup path because OSPF interface costs were changed inconsistently. Here the problem is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

C:

The target prefix SID resolves to the planned node and the corresponding SR LSP is active. This addresses a situation in which a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation; however, on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

Question 148

At fictional Riverstone Networks 037, a regional service-provider network, during a core-routing acceptance test, operations observes: On a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure. Which failure consequence follows most closely from ignoring this issue?

  1. A correct broadcast network is disrupted by unnecessary configuration changes.
  2. Duplicate identity produces unstable topology and confusing route calculations.
  3. The IGP cannot distribute transit reachability over the circuit.
  4. Customer switching devices can influence provider spanning-tree topology.

Explanation

Correct Answer

A:

A correct broadcast network is disrupted by unnecessary configuration changes. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. Confirm the DR and BDR election and distinguish the required adjacency state for each neighbor relationship.

Incorrect Answers

B:

Duplicate identity produces unstable topology and confusing route calculations. It is useful for situations where two routers in the same routing domain advertise the same OSPF router ID after cloning a lab template; the reported fault, though, is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

C:

The IGP cannot distribute transit reachability over the circuit. That relates to circumstances in which two provider routers on a point-to-point circuit cannot form an OSPF adjacency because their interfaces use different area IDs. Here the problem is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

D:

Customer switching devices can influence provider spanning-tree topology. This addresses a situation in which a subscriber accidentally connects a switch that sends BPDUs into a provider edge expected to accept endpoints only; however, on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

Question 149

In a separate fictional JNCIS-SP lab review for Windmere Fiber 038, a carrier-edge and core routing team, following a monitored network change window, engineers find: On a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure. What intervention most directly restores the intended routing or switching behavior?

  1. Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement.
  2. Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes.
  3. Confirm the DR and BDR election and distinguish the required adjacency state for each neighbor relationship.
  4. Confirm MED comparison applicability and use a suitable local outbound policy if needed.

Explanation

Correct Answer

C:

Confirm the DR and BDR election and distinguish the required adjacency state for each neighbor relationship. Expected DR and BDR peers are Full while the relevant non-DR relationship can legitimately remain 2-Way. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other.

Incorrect Answers

A:

Use passive OSPF operation on the customer-facing interface while retaining intended prefix advertisement. This could help if a provider PE inadvertently attempts to form an OSPF adjacency on a customer LAN that should advertise reachability only, but not when on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

B:

Stabilize the underlying neighbor relationship and verify refreshed LSA lifetimes. This relates to a case where an OSPF route vanishes intermittently because a neighbor cannot refresh topology information after repeated link resets; the current situation is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

D:

Confirm MED comparison applicability and use a suitable local outbound policy if needed. That relates to circumstances in which a network expects MED to control all outbound peer choices even when comparing routes learned from unrelated neighboring autonomous systems. Here the problem is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

Question 150

In a separate fictional JNCIS-SP lab review for Windmere Fiber 038, a carrier-edge and core routing team, following a monitored network change window, engineers find: On a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure. Which networking principle explains why the proposed correction is appropriate?

  1. OSPF interface network type influences neighbor discovery and DR behavior.
  2. OSPF shortest-path calculations rely on consistent synchronized link-state information within an area.
  3. On multiaccess links, not all OSPF neighbors must become fully adjacent to each other.
  4. An established BGP session does not by itself establish which received path will be preferred.

Explanation

Correct Answer

C:

On multiaccess links, not all OSPF neighbors must become fully adjacent to each other. Expected DR and BDR peers are Full while the relevant non-DR relationship can legitimately remain 2-Way. Confirm the DR and BDR election and distinguish the required adjacency state for each neighbor relationship.

Incorrect Answers

A:

OSPF interface network type influences neighbor discovery and DR behavior. It is relevant if OSPF adjacency setup fails on a network whose configured link type does not reflect point-to-point topology, but the reported issue is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

B:

OSPF shortest-path calculations rely on consistent synchronized link-state information within an area. This could help if two supposed adjacent routers have different views of a backbone link because database synchronization never completes, but not when on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

D:

An established BGP session does not by itself establish which received path will be preferred. It is useful for situations where a prefix switches BGP best paths and operators cannot explain the result because only peer state is monitored; the reported fault, though, is that on a broadcast segment, one non-designated router shows a peer at 2-Way and an operator incorrectly treats it as a failure.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests