Question 700At fictional Glenwood Connectivity 175, a regional service-provider network, during a preproduction design validation, operations observes: An MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. Which operational harm would persist without the intended correction? Packets cannot travel the intended MPLS transport path. Traffic bypasses an approved low-latency or protected path. Labeled packets are discarded at the affected core node. Misdiagnosis delays restoration because absent control-plane information is overlooked. ExplanationCorrect Answer A:Packets cannot travel the intended MPLS transport path. LDP distributes label mappings needed for label-switched forwarding paths. Check label advertisements for the FEC and restore a valid LDP downstream binding. Incorrect Answers B:Traffic bypasses an approved low-latency or protected path. It is useful for situations where a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change; the reported fault, though, is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. C:Labeled packets are discarded at the affected core node. That relates to circumstances in which an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing. Here the problem is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. D:Misdiagnosis delays restoration because absent control-plane information is overlooked. This addresses a situation in which operators expect a customer prefix from another area but only inspect local interface counters and never examine link-state advertisements; however, an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop.
Question 701In a separate fictional JNCIS-SP lab review for Hillside Transit 176, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. What should the Junos specialist change first to resolve this specific fault? Inspect RSVP signaling errors and hop-level LSP state to isolate the path failure. Recalculate the supported reservation and link bandwidth design before retrying. Check label advertisements for the FEC and restore a valid LDP downstream binding. Account for GRE and outer-IP overhead and implement a supported MTU or fragmentation strategy. ExplanationCorrect Answer C:Check label advertisements for the FEC and restore a valid LDP downstream binding. All transit hops display usable label bindings for the target FEC. LDP distributes label mappings needed for label-switched forwarding paths. Incorrect Answers A:Inspect RSVP signaling errors and hop-level LSP state to isolate the path failure. This could help if an RSVP LSP stays down but engineers only examine the ingress router's IP default route, but not when an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. B:Recalculate the supported reservation and link bandwidth design before retrying. This relates to a case where an RSVP LSP setup fails after requested bandwidth exceeds available reservable capacity on a transit link; the current situation is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. D:Account for GRE and outer-IP overhead and implement a supported MTU or fragmentation strategy. That relates to circumstances in which large packets fail on an overlay while small probes work because encapsulation overhead exceeds path MTU. Here the problem is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop.
Question 702In a separate fictional JNCIS-SP lab review for Hillside Transit 176, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. What technical principle underlies the right remedy? Protocol adjacency health does not prove every required MPLS forwarding entry exists. A prefix SID normally expresses reachability to a node or prefix along the underlying shortest path. MSTP topology calculations depend on compatible region identity and instance membership. LDP distributes label mappings needed for label-switched forwarding paths. ExplanationCorrect Answer D:LDP distributes label mappings needed for label-switched forwarding paths. All transit hops display usable label bindings for the target FEC. Check label advertisements for the FEC and restore a valid LDP downstream binding. Incorrect Answers A:Protocol adjacency health does not prove every required MPLS forwarding entry exists. It is relevant if monitoring checks only LDP adjacency state and never detects missing forwarding labels for a critical PE loopback, but the reported issue is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. B:A prefix SID normally expresses reachability to a node or prefix along the underlying shortest path. This could help if a team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path, but not when an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. C:MSTP topology calculations depend on compatible region identity and instance membership. This relates to a case where two interconnected switches place the same VLAN in different MSTP instances, leading to inconsistent blocking behavior; the current situation is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop.
Question 703In a separate fictional JNCIS-SP lab review for Hillside Transit 176, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. Which acceptance finding demonstrates the affected service has recovered? The target prefix SID resolves to the planned node and the corresponding SR LSP is active. A targeted incoming label maps to the intended outgoing label and interface. All transit hops display usable label bindings for the target FEC. A correctly sized customer frame traverses the entire provider handoff without drops. ExplanationCorrect Answer C:All transit hops display usable label bindings for the target FEC. Check label advertisements for the FEC and restore a valid LDP downstream binding. LDP distributes label mappings needed for label-switched forwarding paths. Incorrect Answers A:The target prefix SID resolves to the planned node and the corresponding SR LSP is active. This is applicable when a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation; the present condition is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. B:A targeted incoming label maps to the intended outgoing label and interface. It is relevant if an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing, but the reported issue is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. D:A correctly sized customer frame traverses the entire provider handoff without drops. This relates to a case where a service-provider QinQ link carries small frames but drops customer frames when the extra VLAN header exceeds the link MTU; the current situation is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop.
Question 704In a separate fictional JNCIS-SP lab review for Hillside Transit 176, a carrier-edge and core routing team, following a maintenance rollback review, engineers find: An MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. What is the direct residual network risk if the fault remains unresolved? The engineered service remains unavailable or overcommits transit capacity. A premium customer service traverses a congested or disallowed link. Packets cannot travel the intended MPLS transport path. Intermittent route loss causes repeated customer outages. ExplanationCorrect Answer C:Packets cannot travel the intended MPLS transport path. Check label advertisements for the FEC and restore a valid LDP downstream binding. LDP distributes label mappings needed for label-switched forwarding paths. Incorrect Answers A:The engineered service remains unavailable or overcommits transit capacity. That could help when an RSVP LSP setup fails after requested bandwidth exceeds available reservable capacity on a transit link; here, an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. B:A premium customer service traverses a congested or disallowed link. This is applicable when an RSVP-signaled LSP follows a congested transit hop instead of the approved engineered route; the present condition is that an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop. D:Intermittent route loss causes repeated customer outages. This could help if an upstream prefix repeatedly withdraws and returns but the operations view shows only the current best route, but not when an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop.
Question 705At fictional Westbridge Exchange 177, a regional service-provider network, during a core-routing acceptance test, operations observes: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. Which targeted remediation best fits the reported behavior? Align route resolution and LSP preference with the documented transport service intent. Check label advertisements for the FEC and restore a valid LDP downstream binding. Apply the supported LDP and IGP synchronization design and verify staged activation. Investigate Layer 2 topology, bridge membership and possible loop before route-policy changes. ExplanationCorrect Answer C:Apply the supported LDP and IGP synchronization design and verify staged activation. MPLS traffic can fail if shortest-path selection moves onto a link without ready label forwarding. The link carries protected MPLS traffic only after the required label state is available. Incorrect Answers A:Align route resolution and LSP preference with the documented transport service intent. This could matter when a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. In this case, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. B:Check label advertisements for the FEC and restore a valid LDP downstream binding. That could help when an MPLS service route is reachable at IP level but its LDP label binding is missing on one hop; here, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. D:Investigate Layer 2 topology, bridge membership and possible loop before route-policy changes. It is relevant if a MAC moves rapidly among provider ports after a cabling change, yet troubleshooting focuses only on IP routing tables, but the reported issue is that a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage.
Question 706At fictional Westbridge Exchange 177, a regional service-provider network, during a core-routing acceptance test, operations observes: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. Why is this particular correction the best fit for the stated defect? MPLS traffic can fail if shortest-path selection moves onto a link without ready label forwarding. A route's presence is insufficient if its selected MPLS transport next hop is unusable. MPLS label forwarding must follow the current resolved transport topology. IBGP connects peers within an AS while EBGP represents inter-AS exchange with different policy expectations. ExplanationCorrect Answer A:MPLS traffic can fail if shortest-path selection moves onto a link without ready label forwarding. Apply the supported LDP and IGP synchronization design and verify staged activation. The link carries protected MPLS traffic only after the required label state is available. Incorrect Answers B:A route's presence is insufficient if its selected MPLS transport next hop is unusable. This could matter when a service path references an LSP that is down, but its IP route remains visible in the route table. In this case, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. C:MPLS label forwarding must follow the current resolved transport topology. That could help when after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device; here, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. D:IBGP connects peers within an AS while EBGP represents inter-AS exchange with different policy expectations. This is applicable when an operator configures an internal route-reflector session as EBGP and introduces an unintended AS boundary; the present condition is that a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage.
Question 707At fictional Westbridge Exchange 177, a regional service-provider network, during a core-routing acceptance test, operations observes: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. What direct observation would prove the corrective action worked? A controlled packet trace follows the intended segment program under the chosen IGP topology. The link carries protected MPLS traffic only after the required label state is available. The selected service resolves over the intended RSVP LSP and follows engineered hops. The route table and forwarding lookup show the expected metric-driven next hop. ExplanationCorrect Answer B:The link carries protected MPLS traffic only after the required label state is available. MPLS traffic can fail if shortest-path selection moves onto a link without ready label forwarding. Apply the supported LDP and IGP synchronization design and verify staged activation. Incorrect Answers A:A controlled packet trace follows the intended segment program under the chosen IGP topology. That option concerns a team assumes an SR prefix segment guarantees a strict hop-by-hop explicit path, but traffic follows the current IGP shortest path. The problem here is different: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. C:The selected service resolves over the intended RSVP LSP and follows engineered hops. This could matter when a tunnel intended for RSVP engineering instead uses unconstrained LDP forwarding after a route-resolution change. In this case, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. D:The route table and forwarding lookup show the expected metric-driven next hop. That could help when the IS-IS session reports established but a core prefix still follows an unexpected path after a circuit metric change; here, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage.
Question 708At fictional Westbridge Exchange 177, a regional service-provider network, during a core-routing acceptance test, operations observes: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. Which failure consequence follows most closely from ignoring this issue? A partial label-distribution failure persists without an alert. MPLS traffic remains broken despite restored IGP neighbors. The interprovider route exchange remains unavailable. Traffic is briefly blackholed during normal network convergence. ExplanationCorrect Answer D:Traffic is briefly blackholed during normal network convergence. MPLS traffic can fail if shortest-path selection moves onto a link without ready label forwarding. Apply the supported LDP and IGP synchronization design and verify staged activation. Incorrect Answers A:A partial label-distribution failure persists without an alert. The choice would be appropriate if monitoring checks only LDP adjacency state and never detects missing forwarding labels for a critical PE loopback. Here, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. B:MPLS traffic remains broken despite restored IGP neighbors. That option concerns after an IGP reconvergence, an old MPLS label still points to a failed interface on one transit device. The problem here is different: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. C:The interprovider route exchange remains unavailable. It addresses a different problem: An external BGP session never reaches Established because the local peer definition uses the wrong remote AS. Here, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage.
Question 709In a separate fictional JNCIS-SP lab review for Crestland Networks 178, a carrier-edge and core routing team, following a monitored network change window, engineers find: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. What intervention most directly restores the intended routing or switching behavior? Apply the supported LDP and IGP synchronization design and verify staged activation. Check transit MPLS forwarding state and repair the missing label operation. Interpret MPLS TTL and traceroute behavior using the configured transport model. Use distinct virtual-switch or bridge-domain contexts with explicit interface membership. ExplanationCorrect Answer A:Apply the supported LDP and IGP synchronization design and verify staged activation. The link carries protected MPLS traffic only after the required label state is available. MPLS traffic can fail if shortest-path selection moves onto a link without ready label forwarding. Incorrect Answers B:Check transit MPLS forwarding state and repair the missing label operation. The choice would be appropriate if an MPLS LSP is reported as configured but the expected outgoing label swap entry is missing. Here, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. C:Interpret MPLS TTL and traceroute behavior using the configured transport model. That option concerns traceroute across an MPLS core shows fewer visible routers than expected and engineers assume the packets are taking a forbidden shortcut. The problem here is different: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. D:Use distinct virtual-switch or bridge-domain contexts with explicit interface membership. It addresses a different problem: Two customer VLANs merge unexpectedly after a virtual-switch template is copied across separate services. Here, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage.
Question 710In a separate fictional JNCIS-SP lab review for Crestland Networks 178, a carrier-edge and core routing team, following a monitored network change window, engineers find: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. Which networking principle explains why the proposed correction is appropriate? Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. MPLS traffic can fail if shortest-path selection moves onto a link without ready label forwarding. Protocol adjacency health does not prove every required MPLS forwarding entry exists. GRE encapsulates inner packets in outer IP packets that must reach the remote tunnel endpoint. ExplanationCorrect Answer B:MPLS traffic can fail if shortest-path selection moves onto a link without ready label forwarding. The link carries protected MPLS traffic only after the required label state is available. Apply the supported LDP and IGP synchronization design and verify staged activation. Incorrect Answers A:Segment routing uses advertised segment identifiers to steer packets across an MPLS topology. That relates to circumstances in which a provider uses MPLS segment routing but a node advertises a prefix SID inconsistent with the intended domain allocation. Here the problem is that a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. C:Protocol adjacency health does not prove every required MPLS forwarding entry exists. The choice would be appropriate if monitoring checks only LDP adjacency state and never detects missing forwarding labels for a critical PE loopback. Here, a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage. D:GRE encapsulates inner packets in outer IP packets that must reach the remote tunnel endpoint. That option concerns a configured GRE tunnel stays unusable after the remote outer IP endpoint changes. The problem here is different: A new core link attracts IP routes before its LDP labels are ready, causing a transient service outage.