Question 40In a separate fictional JNCIS-SP lab review for Fairhaven Broadband 010, a carrier-edge and core routing team, following a new customer connectivity turn-up, engineers find: A router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing. What likely service impact does this condition create? A false fix redirects a customer subnet onto an inappropriate aggregate route. Packets to the customer prefix are dropped despite the static route statement being present. Invalid or unintended address space can enter forwarding decisions and misdirect traffic. IPv6 traffic is entirely lost due to an unsuitable policy match. ExplanationCorrect Answer C:Invalid or unintended address space can enter forwarding decisions and misdirect traffic. Review Junos martian-route behavior and explicit exceptions before accepting the suspect prefix. Martian route handling protects the routing table from addresses that should not be treated as normally reachable. Incorrect Answers A:A false fix redirects a customer subnet onto an inappropriate aggregate route. This relates to a case where an operator changes route preference to make a broader prefix override a healthy more-specific prefix; the current situation is that a router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing. B:Packets to the customer prefix are dropped despite the static route statement being present. It is useful for situations where a provider edge has a static route for a customer prefix, but its next hop resolves only through a disconnected interface; the reported fault, though, is that a router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing. D:IPv6 traffic is entirely lost due to an unsuitable policy match. This addresses a situation in which a prefix-list filter written for IPv4 is applied conceptually to IPv6 routing, and all intended IPv6 routes vanish; however, a router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing.
Question 41At fictional Cedarwater Transit 011, a regional service-provider network, during a planned PE-to-core handoff, operations observes: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. Which configuration or operational correction most directly addresses this failure? Review Junos martian-route behavior and explicit exceptions before accepting the suspect prefix. Inspect the aggregate route contributors and align the summary with the intended component prefixes. Align the intended OSPF area on both endpoints and inspect neighbor state. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. ExplanationCorrect Answer D:Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Independent routing instances provide logically isolated route resolution and forwarding contexts. Each tenant's route lookup uses its own instance table and reaches only authorized customer next hops. Incorrect Answers A:Review Junos martian-route behavior and explicit exceptions before accepting the suspect prefix. This could help if a router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing, but not when customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. B:Inspect the aggregate route contributors and align the summary with the intended component prefixes. This relates to a case where a summary prefix is advertised even though operators have not confirmed which customer specifics contribute to it; the current situation is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. C:Align the intended OSPF area on both endpoints and inspect neighbor state. It is useful for situations where two provider routers on a point-to-point circuit cannot form an OSPF adjacency because their interfaces use different area IDs; the reported fault, though, is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table.
Question 42At fictional Cedarwater Transit 011, a regional service-provider network, during a planned PE-to-core handoff, operations observes: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. Which Junos forwarding or control-plane rule applies to this case? Independent routing instances provide logically isolated route resolution and forwarding contexts. Route lookup and default selection occur within the configured routing-instance context. Equal-cost candidate routes alone do not prove that forwarding uses multiple next hops. IS-IS authentication parameters must match for participating routers to exchange protocol information. ExplanationCorrect Answer A:Independent routing instances provide logically isolated route resolution and forwarding contexts. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Each tenant's route lookup uses its own instance table and reaches only authorized customer next hops. Incorrect Answers B:Route lookup and default selection occur within the configured routing-instance context. This could help if a route lookup for a management instance falls back to the global default, which the design prohibits, but not when customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. C:Equal-cost candidate routes alone do not prove that forwarding uses multiple next hops. This relates to a case where a provider expects two equal-cost links to share traffic, but forwarding consistently chooses one because the second next hop was not installed; the current situation is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. D:IS-IS authentication parameters must match for participating routers to exchange protocol information. It is useful for situations where a provider IS-IS circuit stops forming neighbors after the authentication key is changed on only one end; the reported fault, though, is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table.
Question 43At fictional Cedarwater Transit 011, a regional service-provider network, during a planned PE-to-core handoff, operations observes: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. What operational evidence best establishes successful remediation? The customer route is active in the routing table and its forwarding next hop points to the reachable transit interface. Each tenant's route lookup uses its own instance table and reaches only authorized customer next hops. The route detail identifies the intended contributing prefixes and the summary is active only in the planned circumstances. Both client sessions stabilize and expected reflected routes reach peers. ExplanationCorrect Answer B:Each tenant's route lookup uses its own instance table and reaches only authorized customer next hops. Independent routing instances provide logically isolated route resolution and forwarding contexts. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Incorrect Answers A:The customer route is active in the routing table and its forwarding next hop points to the reachable transit interface. This is applicable when a provider edge has a static route for a customer prefix, but its next hop resolves only through a disconnected interface; the present condition is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. C:The route detail identifies the intended contributing prefixes and the summary is active only in the planned circumstances. This could help if a summary prefix is advertised even though operators have not confirmed which customer specifics contribute to it, but not when customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. D:Both client sessions stabilize and expected reflected routes reach peers. This relates to a case where an internal client learns routes from another client only intermittently after the route-reflector peering address changes; the current situation is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table.
Question 44At fictional Cedarwater Transit 011, a regional service-provider network, during a planned PE-to-core handoff, operations observes: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. Which operational harm would persist without the intended correction? Traffic crosses a customer boundary and violates contractual segmentation. Sensitive application traffic bypasses the required upstream inspection or transit path. An inappropriate summary attracts packets for destinations the provider cannot actually reach. Traffic is briefly blackholed during normal network convergence. ExplanationCorrect Answer A:Traffic crosses a customer boundary and violates contractual segmentation. Independent routing instances provide logically isolated route resolution and forwarding contexts. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Incorrect Answers B:Sensitive application traffic bypasses the required upstream inspection or transit path. This is applicable when a traffic class should be steered into an alternate routing instance but the firewall filter maps it to the default route lookup; the present condition is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. C:An inappropriate summary attracts packets for destinations the provider cannot actually reach. It is relevant if a summary prefix is advertised even though operators have not confirmed which customer specifics contribute to it, but the reported issue is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. D:Traffic is briefly blackholed during normal network convergence. This could help if a new core link attracts IP routes before its LDP labels are ready, causing a transient service outage, but not when customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table.
Question 45In a separate fictional JNCIS-SP lab review for Riverstone Networks 012, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. What should the Junos specialist change first to resolve this specific fault? Compare protocol route state with the active route and forwarding-table next-hop installation. Correct the static next hop to a reachable transit address and confirm the selected route can resolve. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Check MAC aging and traffic timing before adding disruptive forwarding restrictions. ExplanationCorrect Answer C:Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Each tenant's route lookup uses its own instance table and reaches only authorized customer next hops. Independent routing instances provide logically isolated route resolution and forwarding contexts. Incorrect Answers A:Compare protocol route state with the active route and forwarding-table next-hop installation. This could matter when an engineer reports recovery because a route appears in protocol output, but the hardware forwarding table still lacks a usable next hop. In this case, customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. B:Correct the static next hop to a reachable transit address and confirm the selected route can resolve. That could help when a provider edge has a static route for a customer prefix, but its next hop resolves only through a disconnected interface; here, customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. D:Check MAC aging and traffic timing before adding disruptive forwarding restrictions. It is relevant if a customer observes occasional unknown-unicast flooding after long inactivity and assumes every flood is a loop, but the reported issue is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table.
Question 46In a separate fictional JNCIS-SP lab review for Riverstone Networks 012, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. What technical principle underlies the right remedy? Equal-cost candidate routes alone do not prove that forwarding uses multiple next hops. Routing policy terms should match only their explicitly intended routes before altering route attributes. Independent routing instances provide logically isolated route resolution and forwarding contexts. Junos BGP exports only routes accepted by the applicable export policy. ExplanationCorrect Answer C:Independent routing instances provide logically isolated route resolution and forwarding contexts. Each tenant's route lookup uses its own instance table and reaches only authorized customer next hops. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Incorrect Answers A:Equal-cost candidate routes alone do not prove that forwarding uses multiple next hops. It addresses a different problem: A provider expects two equal-cost links to share traffic, but forwarding consistently chooses one because the second next hop was not installed. Here, customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. B:Routing policy terms should match only their explicitly intended routes before altering route attributes. This could matter when a broad routing policy term changes preference for all imported prefixes instead of only the intended test network. In this case, customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. D:Junos BGP exports only routes accepted by the applicable export policy. This is applicable when a customer prefix is not advertised to an upstream peer because the outbound routing policy does not permit it; the present condition is that customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table.
Question 47In a separate fictional JNCIS-SP lab review for Riverstone Networks 012, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. Which acceptance finding demonstrates the affected service has recovered? The customer route is active in the routing table and its forwarding next hop points to the reachable transit interface. Matched traffic uses the alternate instance, while unmatched packets retain the default lookup. Local hosts reach the IRB gateway and authorized routed subnets beyond it. Each tenant's route lookup uses its own instance table and reaches only authorized customer next hops. ExplanationCorrect Answer D:Each tenant's route lookup uses its own instance table and reaches only authorized customer next hops. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Independent routing instances provide logically isolated route resolution and forwarding contexts. Incorrect Answers A:The customer route is active in the routing table and its forwarding next hop points to the reachable transit interface. That option concerns a provider edge has a static route for a customer prefix, but its next hop resolves only through a disconnected interface. The problem here is different: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. B:Matched traffic uses the alternate instance, while unmatched packets retain the default lookup. It addresses a different problem: A traffic class should be steered into an alternate routing instance but the firewall filter maps it to the default route lookup. Here, customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. C:Local hosts reach the IRB gateway and authorized routed subnets beyond it. This could matter when customers on a bridged VLAN can exchange Layer 2 frames but cannot reach other subnets because the IRB gateway is absent. In this case, customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table.
Question 48In a separate fictional JNCIS-SP lab review for Riverstone Networks 012, a carrier-edge and core routing team, following an audit of service-provider handoff behavior, engineers find: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. What is the direct residual network risk if the fault remains unresolved? An inappropriate summary attracts packets for destinations the provider cannot actually reach. Invalid or unintended address space can enter forwarding decisions and misdirect traffic. Traffic crosses a customer boundary and violates contractual segmentation. Duplicate identity creates conflicting LSPs and unstable route computation. ExplanationCorrect Answer C:Traffic crosses a customer boundary and violates contractual segmentation. Put each tenant's interfaces and routes into the intended routing instances and verify separate lookups. Independent routing instances provide logically isolated route resolution and forwarding contexts. Incorrect Answers A:An inappropriate summary attracts packets for destinations the provider cannot actually reach. The choice would be appropriate if a summary prefix is advertised even though operators have not confirmed which customer specifics contribute to it. Here, customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. B:Invalid or unintended address space can enter forwarding decisions and misdirect traffic. That option concerns a router accepts reachability information for an address range the service-provider design treats as invalid for ordinary routing. The problem here is different: Customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table. D:Duplicate identity creates conflicting LSPs and unstable route computation. This could matter when a device cloned from a lab template has the same IS-IS system ID as a production router. In this case, customer A traffic resolves through Customer B's route because both tenants were inadvertently configured in the same routing table.
Question 49At fictional Windmere Fiber 013, a regional service-provider network, during a two-site transit migration, operations observes: A route intended for a monitoring routing table is missing because the RIB group does not include the recipient table. Which targeted remediation best fits the reported behavior? Restrict the discard summary and verify that intended specific routes win for live destinations. Correct the RIB-group import/export table membership and verify only the intended route exchange. Inspect the aggregate route contributors and align the summary with the intended component prefixes. Inspect BGP update history, peer flaps and policy events before changing transit selection. ExplanationCorrect Answer B:Correct the RIB-group import/export table membership and verify only the intended route exchange. A RIB group permits specifically configured routes to be installed into additional routing tables. The target table contains the approved route while unrelated tenant tables remain unchanged. Incorrect Answers A:Restrict the discard summary and verify that intended specific routes win for live destinations. This addresses a situation in which a provider adds a discard summary but accidentally makes it cover reachable customer addresses more specific routes have not yet advertised; however, a route intended for a monitoring routing table is missing because the RIB group does not include the recipient table. C:Inspect the aggregate route contributors and align the summary with the intended component prefixes. That option concerns a summary prefix is advertised even though operators have not confirmed which customer specifics contribute to it. The problem here is different: A route intended for a monitoring routing table is missing because the RIB group does not include the recipient table. D:Inspect BGP update history, peer flaps and policy events before changing transit selection. It addresses a different problem: An upstream prefix repeatedly withdraws and returns but the operations view shows only the current best route. Here, a route intended for a monitoring routing table is missing because the RIB group does not include the recipient table.
Question 50At fictional Windmere Fiber 013, a regional service-provider network, during a two-site transit migration, operations observes: A route intended for a monitoring routing table is missing because the RIB group does not include the recipient table. Why is this particular correction the best fit for the stated defect? Junos directly connected reachability depends on active logical interface configuration and state. Generated routes depend on qualifying routes and their configured policy, not merely on a destination name. Junos BGP exports only routes accepted by the applicable export policy. A RIB group permits specifically configured routes to be installed into additional routing tables. ExplanationCorrect Answer D:A RIB group permits specifically configured routes to be installed into additional routing tables. Correct the RIB-group import/export table membership and verify only the intended route exchange. The target table contains the approved route while unrelated tenant tables remain unchanged. Incorrect Answers A:Junos directly connected reachability depends on active logical interface configuration and state. That relates to circumstances in which a directly connected peering subnet disappears after a logical interface unit is removed during a maintenance template rollout. Here the problem is that a route intended for a monitoring routing table is missing because the RIB group does not include the recipient table. B:Generated routes depend on qualifying routes and their configured policy, not merely on a destination name. This addresses a situation in which a generated default route unexpectedly disappears after the upstream routing policy rejects its contributing route; however, a route intended for a monitoring routing table is missing because the RIB group does not include the recipient table. C:Junos BGP exports only routes accepted by the applicable export policy. The choice would be appropriate if a customer prefix is not advertised to an upstream peer because the outbound routing policy does not permit it. Here, a route intended for a monitoring routing table is missing because the RIB group does not include the recipient table.