McAfee Secured

Exam Code: H12-821

Exam Name: HCIP-Datacom-Core Technology V1.0

Certification Provider: Huawei

100% Huawei H12-821 Guaranteed Success With Testking Training Materials

Get Real H12-821 Exam Questions & Expert Verified Answers as Experienced on the Real Exam!

471 Questions & Answers with Testing Engine

"HCIP-Datacom-Core Technology V1.0 Exam", also known as H12-821 exam, is a Huawei certification exam.

Pass your tests with the always up-to-date H12-821 Exam Engine. Your H12-821 training materials keep you at the head of the pack!

Satisfaction Guaranteed

Money Back Guarantee

Testking provides hassle-free money back guarantee with our products. That is because we have 100% trust in the abilities of our professional and experience product team, and our record is a proof of that.

99.6% PASS RATE
Was: $137.49
Now: $124.99

Huawei H12-821 Practice Test 2

Question 10

The datacom engineering team at a municipal transport operator during a simulated failover test reviews this independent fictional networking case: One router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down. The team applies this remedy: Restore accurate failure detection and re-originate the affected OSPF topology information. Which observation would directly demonstrate that this specific issue is resolved?

  1. ABRs display correct backbone reachability and previously missing interarea routes appear
  2. The ABR default route appears in the stub area and external destinations remain reachable
  3. Authentication error counters stop increasing and a new Full adjacency is established
  4. The relevant LSA changes, SPF runs, and the affected route moves to a healthy alternate

Explanation

Correct Answer

D:

The relevant LSA changes, SPF runs, and the affected route moves to a healthy alternate. This is a directly observable check for the proposed correction: Restore accurate failure detection and re-originate the affected OSPF topology information. The particular failure being investigated is: One router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down.

Incorrect Answers

A:

Two nonbackbone OSPF areas were connected without a valid area 0 path and interarea routes are inconsistent. ABRs display correct backbone reachability and previously missing interarea routes appear. This observation does not prove the correction for the reported defect: One router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down. SPF can only remove unusable paths promptly after their topology state is correctly detected and flooded.

B:

The ABR default route appears in the stub area and external destinations remain reachable. This check belongs to an engineer expects Type-5 external LSAs inside an OSPF stub area and mistakes their absence for a routing fault. The actual defect is different: One router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down. Restore accurate failure detection and re-originate the affected OSPF topology information.

C:

Authentication error counters stop increasing and a new Full adjacency is established. This check belongs to an OSPF adjacency stops forming after a scheduled authentication-key rotation on one end only. The actual defect is different: One router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down. Persistently stale link state can redirect traffic into a dead transport segment.

Question 11

The datacom engineering team at a municipal transport operator during a simulated failover test reviews this independent fictional networking case: One router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down. A proposed remedy is: Restore accurate failure detection and re-originate the affected OSPF topology information. Which technical principle most directly supports this remedy?

  1. ABR summaries reduce LSDB size but overbroad summaries can attract packets for nonexistent destinations
  2. SPF can only remove unusable paths promptly after their topology state is correctly detected and flooded
  3. OSPF shortest-path selection uses cumulative interface cost, not real-time measured bandwidth by itself
  4. ASBR route aggregation reduces external advertisements without replacing ordinary ABR interarea summarization

Explanation

Correct Answer

B:

SPF can only remove unusable paths promptly after their topology state is correctly detected and flooded. This directly explains why the corrective operation is appropriate: Restore accurate failure detection and re-originate the affected OSPF topology information. The observed acceptance evidence should be: The relevant LSA changes, SPF runs, and the affected route moves to a healthy alternate.

Incorrect Answers

A:

ABR summaries reduce LSDB size but overbroad summaries can attract packets for nonexistent destinations. That rule governs a different situation: An area border router advertises a broad summary that includes subnets withdrawn after a site closure. Here, one router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down. SPF can only remove unusable paths promptly after their topology state is correctly detected and flooded.

C:

When after an uplink upgrade, OSPF still prefers a slower backup circuit because interface reference bandwidth and explicit cost settings were not reviewed, OSPF shortest-path selection uses cumulative interface cost, not real-time measured bandwidth by itself. By contrast, one router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down; restore accurate failure detection and re-originate the affected OSPF topology information.

D:

ASBR route aggregation reduces external advertisements without replacing ordinary ABR interarea summarization. That principle is relevant when an ASBR emits hundreds of connected external prefixes individually and overwhelms branch route tables. Here, one router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down; the relevant LSA changes, SPF runs, and the affected route moves to a healthy alternate.

Question 12

The datacom engineering team at a cross-border logistics provider after a monitored link change reviews this independent fictional networking case: Two EVPN leaf devices originate indistinguishable VPN NLRI because the service route identifiers were copied incorrectly. If this issue remains unresolved, what immediate availability or security risk follows most directly?

  1. Uncontrolled source interface selection causes intermittent neighbor resets after link changes
  2. Duplicate route identifiers can obscure independent EVPN path advertisements
  3. A valid-looking iBGP route may be unusable when the external next hop is unresolved
  4. Inbound traffic may continue on an unwanted provider if external policy is not validated

Explanation

Correct Answer

B:

Duplicate route identifiers can obscure independent EVPN path advertisements. Leaving the exact fault unresolved means: Two EVPN leaf devices originate indistinguishable VPN NLRI because the service route identifiers were copied incorrectly. The intended response is: Assign route distinguishers suitable for creating unique originating VPN route identifiers.

Incorrect Answers

A:

Uncontrolled source interface selection causes intermittent neighbor resets after link changes. That risk belongs to a separate condition: Two iBGP speakers configured with loopback neighbor addresses send sessions from unexpected physical interface addresses. Here, two EVPN leaf devices originate indistinguishable VPN NLRI because the service route identifiers were copied incorrectly; route distinguishers distinguish otherwise identical VPN address advertisements; they do not themselves control import permission.

C:

A valid-looking iBGP route may be unusable when the external next hop is unresolved. That risk belongs to a separate condition: An iBGP peer learns external prefixes but cannot install them because the original eBGP next hop is not reachable internally. Here, two EVPN leaf devices originate indistinguishable VPN NLRI because the service route identifiers were copied incorrectly; assign route distinguishers suitable for creating unique originating VPN route identifiers.

D:

When an enterprise wants to influence how some external networks enter its secondary ISP, but it changes local preference inside its own AS instead, inbound traffic may continue on an unwanted provider if external policy is not validated. The present failure is different: Two EVPN leaf devices originate indistinguishable VPN NLRI because the service route identifiers were copied incorrectly. EVPN control-plane entries retain unique per-origin VPN identifiers and remote paths coexist.

Question 13

The datacom engineering team at a local rail transit network while validating change-control evidence reviews this independent fictional networking case: A multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. If this issue remains unresolved, what immediate availability or security risk follows most directly?

  1. Mismatched RPs can partition an otherwise connected multicast domain
  2. Misapplied ASM behavior can select an unintended stream source and undermine access expectations
  3. Persistent shared-tree detours can congest core links and degrade streaming performance
  4. Group delivery becomes erratic when receiver membership is allowed to age silently

Explanation

Correct Answer

A:

Mismatched RPs can partition an otherwise connected multicast domain. Leaving the exact fault unresolved means: A multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. The intended response is: Configure a consistent appropriate rendezvous point mapping and inspect source registration paths.

Incorrect Answers

B:

A receiver requests a specific-source multicast stream but the network treats its membership as ordinary any-source group state. In that situation, misapplied ASM behavior can select an unintended stream source and undermine access expectations. Here instead, a multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. PIM-SM uses an RP to build initial shared-tree reachability for ASM groups.

C:

Persistent shared-tree detours can congest core links and degrade streaming performance. That consequence could follow when a distant receiver continues using a long shared tree after a short direct source path is available and capacity is strained. Here, a multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings; configure a consistent appropriate rendezvous point mapping and inspect source registration paths.

D:

A VLAN with multicast hosts has no functioning IGMP querier after its original gateway moves away. In that situation, group delivery becomes erratic when receiver membership is allowed to age silently. Here instead, a multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. RP mappings agree and receivers establish expected PIM joins with working source traffic.

Question 14

The datacom engineering team at a regional newspaper publisher after an incident review reviews this independent fictional networking case: An engineer expects Type-5 external LSAs inside an OSPF stub area and mistakes their absence for a routing fault. Which corrective engineering action most directly addresses this problem?

  1. Apply appropriately scoped external prefix summarization at the originating ASBR
  2. Evaluate E1 versus E2 external metric behavior and configure the intended metric type consistently
  3. Restore accurate failure detection and re-originate the affected OSPF topology information
  4. Validate stub-area configuration and ensure the ABR advertises the intended default route into the area

Explanation

Correct Answer

D:

Validate stub-area configuration and ensure the ABR advertises the intended default route into the area. This is the specific action that addresses the fictional fault: An engineer expects Type-5 external LSAs inside an OSPF stub area and mistakes their absence for a routing fault. The governing technical reason is: Standard stub areas suppress Type-5 external LSAs and normally rely on an ABR-provided default for external reachability. Verify by checking: The ABR default route appears in the stub area and external destinations remain reachable.

Incorrect Answers

A:

When an ASBR emits hundreds of connected external prefixes individually and overwhelms branch route tables, applying appropriately scoped external prefix summarization at the originating ASBR could be appropriate. Here, an engineer expects Type-5 external LSAs inside an OSPF stub area and mistakes their absence for a routing fault. Standard stub areas suppress Type-5 external LSAs and normally rely on an ABR-provided default for external reachability.

B:

When a remote site incorrectly chooses an external OSPF route that ignores material internal distance to competing exit points, evaluating E1 versus E2 external metric behavior and configuring the intended metric type consistently could be appropriate. Here, an engineer expects Type-5 external LSAs inside an OSPF stub area and mistakes their absence for a routing fault. Validate stub-area configuration and ensure the ABR advertises the intended default route into the area.

C:

One router continues advertising a failed transit link because the local interface reports Up while an intermediate transport component is down. Restoring accurate failure detection and re-originate the affected OSPF topology information can respond to that condition, but it would not correct the reported fault: An engineer expects Type-5 external LSAs inside an OSPF stub area and mistakes their absence for a routing fault. The ABR default route appears in the stub area and external destinations remain reachable.

Question 15

The datacom engineering team at a university research campus while tracing a degraded application flow reviews this independent fictional networking case: A multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. Which corrective engineering action most directly addresses this problem?

  1. Configure compatible SSM group ranges and source-aware membership signalling
  2. Verify the multicast RPF route and correct source reachability or appropriate multicast routing state
  3. Enable and validate snooping with an operative querier and approved multicast router ports
  4. Configure a consistent appropriate rendezvous point mapping and inspect source registration paths

Explanation

Correct Answer

D:

Configure a consistent appropriate rendezvous point mapping and inspect source registration paths. This is the specific action that addresses the fictional fault: A multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. The governing technical reason is: PIM-SM uses an RP to build initial shared-tree reachability for ASM groups. Verify by checking: RP mappings agree and receivers establish expected PIM joins with working source traffic.

Incorrect Answers

A:

Configuring compatible SSM group ranges and source-aware membership signalling is relevant when a receiver requests a specific-source multicast stream but the network treats its membership as ordinary any-source group state. It does not resolve this case: A multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. PIM-SM uses an RP to build initial shared-tree reachability for ASM groups.

B:

When a multicast stream reaches a router from an interface other than its unicast reverse path toward the source and is discarded, verifying the multicast RPF route and correcting source reachability or appropriate multicast routing state could be appropriate. Here, a multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. Configure a consistent appropriate rendezvous point mapping and inspect source registration paths.

C:

Enabling and validating snooping with an operative querier and approved multicast router ports is relevant when a switch floods a high-rate multicast feed to all access ports because no reliable IGMP snooping membership table was built. It does not resolve this case: A multicast source in a sparse-mode domain sends traffic but remote listeners receive nothing because the routers have inconsistent RP mappings. RP mappings agree and receivers establish expected PIM joins with working source traffic.

Question 16

The datacom engineering team at a government service campus after a monitored link change reviews this independent fictional networking case: Clients on a new IPv6 VLAN fail to obtain global addresses because router advertisements lack the intended autonomous prefix information. If this issue remains unresolved, what immediate availability or security risk follows most directly?

  1. Ambiguous link-local next hops can make IPv6 forwarding fail despite apparently valid prefixes
  2. Broken RA configuration leaves clients with only link-local reachability
  3. Duplicate IPv6 addresses create intermittent black holes and service identity confusion
  4. Untested community handling can leak routes outside an intended operational boundary

Explanation

Correct Answer

B:

Broken RA configuration leaves clients with only link-local reachability. Leaving the exact fault unresolved means: Clients on a new IPv6 VLAN fail to obtain global addresses because router advertisements lack the intended autonomous prefix information. The intended response is: Correct router advertisement prefix and flags for the chosen IPv6 addressing design.

Incorrect Answers

A:

Ambiguous link-local next hops can make IPv6 forwarding fail despite apparently valid prefixes. That risk belongs to a separate condition: An IPv6 static route uses a link-local next hop without a meaningful outgoing-interface scope and fails to install correctly. Here, clients on a new IPv6 VLAN fail to obtain global addresses because router advertisements lack the intended autonomous prefix information; SLAAC relies on received router advertisement prefix information and associated address configuration flags.

C:

Duplicate IPv6 addresses create intermittent black holes and service identity confusion. That risk belongs to a separate condition: Two replacement servers are configured with the same IPv6 address and one fails to bring the address online. Here, clients on a new IPv6 VLAN fail to obtain global addresses because router advertisements lack the intended autonomous prefix information; correct router advertisement prefix and flags for the chosen IPv6 addressing design.

D:

When a border router tags specific prefixes but the provider does not apply the expected regional no-export treatment, untested community handling can leak routes outside an intended operational boundary. The present failure is different: Clients on a new IPv6 VLAN fail to obtain global addresses because router advertisements lack the intended autonomous prefix information. Clients form valid unique global addresses and default routes from the expected RA source.

Question 17

The datacom engineering team at an agricultural equipment distributor after an incident review reviews this independent fictional networking case: OSPF retains a dead WAN next hop for too long because default neighbor dead timers dominate failure detection. The team applies this remedy: Enable supported BFD tracking for the OSPF adjacency and validate timer compatibility. Which observation would directly demonstrate that this specific issue is resolved?

  1. During a planned circuit interruption, BFD detects failure and routing reconverges within the operational target
  2. Host neighbor tables resolve to the expected virtual MAC and sessions recover after failover
  3. BFD remains stable under expected CPU load and still detects real test failures within requirement
  4. The planned primary device owns the virtual gateway after recovery and failover still works

Explanation

Correct Answer

A:

During a planned circuit interruption, BFD detects failure and routing reconverges within the operational target. This is a directly observable check for the proposed correction: Enable supported BFD tracking for the OSPF adjacency and validate timer compatibility. The particular failure being investigated is: OSPF retains a dead WAN next hop for too long because default neighbor dead timers dominate failure detection.

Incorrect Answers

B:

Host neighbor tables resolve to the expected virtual MAC and sessions recover after failover. That result could validate a repair when a host keeps sending traffic to the old gateway's MAC after a VRRP switchover because the access LAN fails to update its neighbor cache. Here, OSPF retains a dead WAN next hop for too long because default neighbor dead timers dominate failure detection; BFD provides rapid bidirectional failure detection to subscribed routing protocols.

C:

When a high-load device repeatedly declares a healthy BFD session Down because its interval/multiplier settings are too aggressive for platform scheduling, a result such as this is useful: BFD remains stable under expected CPU load and still detects real test failures within requirement. For the reported fault, OSPF retains a dead WAN next hop for too long because default neighbor dead timers dominate failure detection; enable supported BFD tracking for the OSPF adjacency and validate timer compatibility.

D:

A backup gateway becomes VRRP Master after an unrelated restart despite the primary router being healthy. The planned primary device owns the virtual gateway after recovery and failover still works. This observation does not prove the correction for the reported defect: OSPF retains a dead WAN next hop for too long because default neighbor dead timers dominate failure detection. Slow liveness detection can extend avoidable black-hole duration after link failure.

Question 18

The datacom engineering team at a regional newspaper publisher after an incident review reviews this independent fictional networking case: A security ACL intended to block guest-to-management traffic is applied outbound on the wrong interface and never matches those packets. If this issue remains unresolved, what immediate availability or security risk follows most directly?

  1. Misplaced filters allow an unintended trust-boundary crossing without visible policy errors
  2. Broad early deny rules can remove reachable customer networks with no physical fault
  3. Unnoticed remarking causes traffic to lose its intended service priority across domains
  4. An overbroad mask range can enable unauthorized deaggregation and route leaks

Explanation

Correct Answer

A:

Misplaced filters allow an unintended trust-boundary crossing without visible policy errors. Leaving the exact fault unresolved means: A security ACL intended to block guest-to-management traffic is applied outbound on the wrong interface and never matches those packets. The intended response is: Place the filter on the correct ingress or egress direction based on the observed packet path.

Incorrect Answers

B:

Broad early deny rules can remove reachable customer networks with no physical fault. That risk belongs to a separate condition: A new route-policy reject rule unintentionally blocks all later permitted customer prefixes because the rule order is too broad. Here, a security ACL intended to block guest-to-management traffic is applied outbound on the wrong interface and never matches those packets; ACL matching is evaluated at the attachment point and direction, not according to a rule's descriptive name.

C:

Unnoticed remarking causes traffic to lose its intended service priority across domains. That risk belongs to a separate condition: Delay-sensitive packets leave the campus with voice markings but are remarked to best-effort at a trusted border. Here, a security ACL intended to block guest-to-management traffic is applied outbound on the wrong interface and never matches those packets; place the filter on the correct ingress or egress direction based on the observed packet path.

D:

When a routing filter intended to allow a /24 aggregate accidentally allows unauthorized /25 and /32 subprefixes, an overbroad mask range can enable unauthorized deaggregation and route leaks. The present failure is different: A security ACL intended to block guest-to-management traffic is applied outbound on the wrong interface and never matches those packets. Counters increment for prohibited guest probes and approved management flows remain permitted.

Question 19

The datacom engineering team at a distribution warehouse group during a simulated failover test reviews this independent fictional networking case: A migration team treats controller-based network provisioning and SD-WAN overlay path selection as identical capabilities and omits path-performance validation. The team applies this remedy: Define underlay provisioning and SD-WAN overlay policy separately and verify application steering under link degradation. Which observation would directly demonstrate that this specific issue is resolved?

  1. An architectural test shows isolated broadcast domains and approved routed application flows across the boundary
  2. Capture on both sides confirms expected DSCP values and queue counters reflect the correct class
  3. A staged migration test shows correct policy provisioning and overlay failover when the preferred WAN path degrades
  4. Matching gateway interfaces negotiate one Master and user devices reach the correct virtual address

Explanation

Correct Answer

C:

A staged migration test shows correct policy provisioning and overlay failover when the preferred WAN path degrades. This is a directly observable check for the proposed correction: Define underlay provisioning and SD-WAN overlay policy separately and verify application steering under link degradation. The particular failure being investigated is: A migration team treats controller-based network provisioning and SD-WAN overlay path selection as identical capabilities and omits path-performance validation.

Incorrect Answers

A:

An architectural test shows isolated broadcast domains and approved routed application flows across the boundary. This check belongs to a proposed campus core directly bridges user VLANs into a data-center compute fabric without a clear routing and security boundary. The actual defect is different: A migration team treats controller-based network provisioning and SD-WAN overlay path selection as identical capabilities and omits path-performance validation. SDN-oriented control automation and SD-WAN application-aware path control can complement each other but solve different problems.

B:

When delay-sensitive packets leave the campus with voice markings but are remarked to best-effort at a trusted border, a result such as this is useful: Capture on both sides confirms expected DSCP values and queue counters reflect the correct class. For the reported fault, a migration team treats controller-based network provisioning and SD-WAN overlay path selection as identical capabilities and omits path-performance validation; define underlay provisioning and SD-WAN overlay policy separately and verify application steering under link degradation.

D:

Matching gateway interfaces negotiate one Master and user devices reach the correct virtual address. That result could validate a repair when two gateway routers advertise the same virtual router ID on different VLANs due to a template copy error. Here, a migration team treats controller-based network provisioning and SD-WAN overlay path selection as identical capabilities and omits path-performance validation; conflating control orchestration with data-path steering can leave critical applications on poor WAN links.

Question 20

The datacom engineering team at a pharmaceutical testing firm after a planned hardware refresh reviews this independent fictional networking case: A provider-facing interface accepts unexpected routing-control connections from an unapproved adjacent host. A proposed remedy is: Restrict protocol peers and apply appropriate routing authentication or control-plane filtering. Which technical principle most directly supports this remedy?

  1. Stateful firewalls evaluate sessions against zone-aware policies before permitting new flows
  2. Routing control channels should be limited to trusted neighbors independently of ordinary forwarding
  3. IPsec security associations must cover compatible protected flows even when IKE negotiation is successful
  4. VRFs provide separate routing tables, and cross-VRF reachability must be deliberately controlled

Explanation

Correct Answer

B:

Routing control channels should be limited to trusted neighbors independently of ordinary forwarding. This directly explains why the corrective operation is appropriate: Restrict protocol peers and apply appropriate routing authentication or control-plane filtering. The observed acceptance evidence should be: Unauthorized control attempts are rejected while approved peers remain stable.

Incorrect Answers

A:

When a permitted application remains blocked when crossing the Huawei firewall because the zone pairing and rule match conditions are incorrect, stateful firewalls evaluate sessions against zone-aware policies before permitting new flows. By contrast, a provider-facing interface accepts unexpected routing-control connections from an unapproved adjacent host; routing control channels should be limited to trusted neighbors independently of ordinary forwarding.

C:

Two VPN gateways establish IKE but fail to pass the intended private subnet because their phase-two traffic selectors do not agree. IPsec security associations must cover compatible protected flows even when IKE negotiation is successful. The current condition differs: A provider-facing interface accepts unexpected routing-control connections from an unapproved adjacent host. Restrict protocol peers and apply appropriate routing authentication or control-plane filtering.

D:

VRFs provide separate routing tables, and cross-VRF reachability must be deliberately controlled. That rule governs a different situation: Traffic from two tenants reaches each other after an access service is mistakenly placed in a shared routing instance. Here, a provider-facing interface accepts unexpected routing-control connections from an unapproved adjacent host. Unauthorized control attempts are rejected while approved peers remain stable.

HCIP-Datacom-Core Technology V1.0 (H12-821) Practice Tests