Question 570 A user asks what may happen if the issue is not correctly handled: A desktop contains two matching memory modules but both are fitted in slots reserved for a single channel on its board. Which outcome is best supported? Installing an ECC-labeled module alone does not guarantee active error correction A matching slot shape alone does not establish support for every high-density DRAM layout Two modules do not automatically provide dual-channel bandwidth when placed incorrectly Removing a soldered RAM package as if it were a socketed module can damage the board Explanation Correct Answer C:The motherboard diagram shows the recommended paired slots on separate memory channels, consistent with a dual-channel memory population rules. Incorrect Answers A:The CPU, motherboard and firmware compatibility documents do not confirm ECC operation, consistent with an ecc memory requires supported platform hardware. B:The service manual's supported module density and total capacity are below the installed specification, consistent with a maximum supported memory capacity or density limitation. D:The service manual diagrams onboard memory chips and a single removable socket, consistent with a soldered-onboard ram limits user upgrade options.
Question 571 An office PC with an old chipset does not recognize the full capacity of two high-density DIMMs despite both fitting physically. Which prediction follows from this particular failure mode? A matching slot shape alone does not establish support for every high-density DRAM layout Two modules do not automatically provide dual-channel bandwidth when placed incorrectly Matching advertised capacity does not make a compact laptop module fit a desktop DIMM socket Buying a faster module does not force the memory controller to operate above its limits Explanation Correct Answer A:The service manual's supported module density and total capacity are below the installed specification, consistent with a maximum supported memory capacity or density limitation. Incorrect Answers B:The motherboard diagram shows the recommended paired slots on separate memory channels, consistent with a dual-channel memory population rules. C:The service manual lists SO-DIMM modules while the desktop uses standard DIMM slots, consistent with a sodimm versus full-size dimm form factors. D:Firmware reports the lower negotiated memory rate despite a higher-rated module installed, consistent with a memory clock limited by platform and shared settings.
Question 572 When documenting this incident, a technician notes: A laptop has one replaceable SODIMM but the remaining memory is permanently soldered to the motherboard. Which limitation is most directly relevant? Matching advertised capacity does not make a compact laptop module fit a desktop DIMM socket Installing an ECC-labeled module alone does not guarantee active error correction Removing a soldered RAM package as if it were a socketed module can damage the board Two modules do not automatically provide dual-channel bandwidth when placed incorrectly Explanation Correct Answer C:The service manual diagrams onboard memory chips and a single removable socket, consistent with a soldered-onboard ram limits user upgrade options. Incorrect Answers A:The service manual lists SO-DIMM modules while the desktop uses standard DIMM slots, consistent with a sodimm versus full-size dimm form factors. B:The CPU, motherboard and firmware compatibility documents do not confirm ECC operation, consistent with an ecc memory requires supported platform hardware. D:The motherboard diagram shows the recommended paired slots on separate memory channels, consistent with a dual-channel memory population rules.
Question 573 A system supports a lower DDR data rate than a high-speed module's advertised profile and runs the module at a slower standard frequency. Which risk or behavior would be expected if a superficially attractive but incorrect workaround were used? Buying a faster module does not force the memory controller to operate above its limits A matching slot shape alone does not establish support for every high-density DRAM layout Removing a soldered RAM package as if it were a socketed module can damage the board Different DDR generations are not interchangeable simply because both are RAM Explanation Correct Answer A:Firmware reports the lower negotiated memory rate despite a higher-rated module installed, consistent with a memory clock limited by platform and shared settings. Incorrect Answers B:The service manual's supported module density and total capacity are below the installed specification, consistent with a maximum supported memory capacity or density limitation. C:The service manual diagrams onboard memory chips and a single removable socket, consistent with a soldered-onboard ram limits user upgrade options. D:The motherboard supports DDR5 pinout and electrical requirements while the spare is DDR4, consistent with an incompatible ddr memory generation.
Question 574 In a post-repair discussion, the team reviews: A new workstation needs high random I/O and has an available PCIe-connected M.2 socket; the old SATA SSD saturates the SATA link. Which technical implication should be highlighted? A SATA-only host normally cannot address a SAS drive by changing operating-system drivers Not all M.2 sockets provide the PCIe lanes needed by an NVMe drive RPM affects rotational delay and does not turn a mechanical HDD into solid-state storage An M.2 shape alone does not prove a device supports NVMe rather than SATA signaling Explanation Correct Answer D:Benchmarking shows the existing drive capped near SATA throughput while the board supports NVMe, consistent with a nvme ssd over pcie for high-throughput storage. Incorrect Answers A:The drive connector and controller specifications show SAS disks unsupported by the SATA-only host, consistent with a sas drive requires compatible controller interface. B:The device manual specifies SATA-based M.2 storage while the replacement requires PCIe NVMe, consistent with a m.2 physical form factor is not the storage protocol. C:Both drives use magnetic platters but the faster model rotates at 7200 RPM, consistent with a hdd spindle speed influences rotational latency.
Question 575 A client has a thin laptop with a SATA M.2 slot only and buys an NVMe-only M.2 drive that fits mechanically but is invisible. Which technical consequence or limitation best explains why the problem matters? Not all M.2 sockets provide the PCIe lanes needed by an NVMe drive A SATA-only host normally cannot address a SAS drive by changing operating-system drivers An M.2 shape alone does not prove a device supports NVMe rather than SATA signaling RAID 5 parity is not a substitute for a second-failure resilience design Explanation Correct Answer A:The device manual specifies SATA-based M.2 storage while the replacement requires PCIe NVMe, consistent with a m.2 physical form factor is not the storage protocol. Incorrect Answers B:The drive connector and controller specifications show SAS disks unsupported by the SATA-only host, consistent with a sas drive requires compatible controller interface. C:Benchmarking shows the existing drive capped near SATA throughput while the board supports NVMe, consistent with a nvme ssd over pcie for high-throughput storage. D:The array can operate degraded after one disk failure but cannot tolerate a second concurrent member loss, consistent with a raid 5 single-parity tolerance.
Question 576 A user asks what may happen if the issue is not correctly handled: A workstation uses a 5400 RPM mechanical disk and a user complains about slow seeks compared with a supported 7200 RPM disk. Which outcome is best supported? Mirroring protects availability from one drive failure but does not replace backups RPM affects rotational delay and does not turn a mechanical HDD into solid-state storage An M.2 shape alone does not prove a device supports NVMe rather than SATA signaling A RAID 0 stripe has no surviving complete copy after a member disk fails Explanation Correct Answer B:Both drives use magnetic platters but the faster model rotates at 7200 RPM, consistent with a hdd spindle speed influences rotational latency. Incorrect Answers A:The configuration writes the same blocks to both drives and can run degraded with one member, consistent with a raid 1 mirrored disks. C:Benchmarking shows the existing drive capped near SATA throughput while the board supports NVMe, consistent with a nvme ssd over pcie for high-throughput storage. D:The array stripes data across disks without mirrored or parity redundancy, consistent with a raid 0 provides no disk fault tolerance.
Question 577 Two disks are striped for speed, and the loss of one member makes the entire volume unavailable. Which prediction follows from this particular failure mode? A RAID 0 stripe has no surviving complete copy after a member disk fails RAID 5 parity is not a substitute for a second-failure resilience design Dual parity reduces usable capacity but can survive two member failures Mirroring protects availability from one drive failure but does not replace backups Explanation Correct Answer A:The array stripes data across disks without mirrored or parity redundancy, consistent with a raid 0 provides no disk fault tolerance. Incorrect Answers B:The array can operate degraded after one disk failure but cannot tolerate a second concurrent member loss, consistent with a raid 5 single-parity tolerance. C:The storage specification requires tolerance of any two failed members in the parity set, consistent with a raid 6 dual-parity design. D:The configuration writes the same blocks to both drives and can run degraded with one member, consistent with a raid 1 mirrored disks.
Question 578 When documenting this incident, a technician notes: A two-drive workstation must keep identical copies of data on both drives and tolerate one drive failure. Which limitation is most directly relevant? A RAID 0 stripe has no surviving complete copy after a member disk fails Mirroring protects availability from one drive failure but does not replace backups RAID 5 parity is not a substitute for a second-failure resilience design Dual parity reduces usable capacity but can survive two member failures Explanation Correct Answer B:The configuration writes the same blocks to both drives and can run degraded with one member, consistent with a raid 1 mirrored disks. Incorrect Answers A:The array stripes data across disks without mirrored or parity redundancy, consistent with a raid 0 provides no disk fault tolerance. C:The array can operate degraded after one disk failure but cannot tolerate a second concurrent member loss, consistent with a raid 5 single-parity tolerance. D:The storage specification requires tolerance of any two failed members in the parity set, consistent with a raid 6 dual-parity design.
Question 579 A storage box has four equal drives in a RAID 5 array and one disk fails; reads continue but another failure during rebuild threatens data. Which risk or behavior would be expected if a superficially attractive but incorrect workaround were used? Mirroring protects availability from one drive failure but does not replace backups Dual parity reduces usable capacity but can survive two member failures A RAID 0 stripe has no surviving complete copy after a member disk fails RAID 5 parity is not a substitute for a second-failure resilience design Explanation Correct Answer D:The array can operate degraded after one disk failure but cannot tolerate a second concurrent member loss, consistent with a raid 5 single-parity tolerance. Incorrect Answers A:The configuration writes the same blocks to both drives and can run degraded with one member, consistent with a raid 1 mirrored disks. B:The storage specification requires tolerance of any two failed members in the parity set, consistent with a raid 6 dual-parity design. C:The array stripes data across disks without mirrored or parity redundancy, consistent with a raid 0 provides no disk fault tolerance.
Question 580 In a post-repair discussion, the team reviews: An archival server needs a parity array that can survive two simultaneous disk failures without a mirrored copy of every drive. Which technical implication should be highlighted? Dual parity reduces usable capacity but can survive two member failures Mirroring protects availability from one drive failure but does not replace backups RAID 5 parity is not a substitute for a second-failure resilience design RAID 10 may survive some multiple failures but not failure of both disks in one mirror pair Explanation Correct Answer A:The storage specification requires tolerance of any two failed members in the parity set, consistent with a raid 6 dual-parity design. Incorrect Answers B:The configuration writes the same blocks to both drives and can run degraded with one member, consistent with a raid 1 mirrored disks. C:The array can operate degraded after one disk failure but cannot tolerate a second concurrent member loss, consistent with a raid 5 single-parity tolerance. D:The storage layout combines mirrors with striping across pairs rather than simple parity, consistent with a raid 10 striped mirrors.